Part Number Hot Search : 
MAX9718 0T012 2N1883 BZ5260 XC2VP70 SR10150 MX25L12 UM17735
Product Description
Full Text Search
 

To Download M38043F8FP Datasheet File
  If you can't view the Datasheet, Please click here to try to view without PDF Reader .  
　
 

  Datasheet File OCR Text:
 REJ09B0212-0100Z
8
3804 Group (Spec. H)
User's Manual
RENESAS 8-BIT CISC SINGLE-CHIP MICROCOMPUTER 740 FAMILY / 38000 SERIES
Before using this material, please visit our website to confirm that this is the most current document available.
Rev. 1.00 Revision date: Jan 14, 2005
www.renesas.com
Keep safety first in your circuit designs!
1.
Renesas Technology Corp. puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of nonflammable material or (iii) prevention against any malfunction or mishap.
Notes regarding these materials
1.
2.
3.
4.
5.
6. 7.
8.
These materials are intended as a reference to assist our customers in the selection of the Renesas Technology Corp. product best suited to the customer's application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Renesas Technology Corp. or a third party. Renesas Technology Corp. assumes no responsibility for any damage, or infringement of any third-party's rights, originating in the use of any product data, diagrams, charts, programs, algorithms, or circuit application examples contained in these materials. All information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information on products at the time of publication of these materials, and are subject to change by Renesas Technology Corp. without notice due to product improvements or other reasons. It is therefore recommended that customers contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor for the latest product information before purchasing a product listed herein. The information described here may contain technical inaccuracies or typographical errors. Renesas Technology Corp. assumes no responsibility for any damage, liability, or other loss rising from these inaccuracies or errors. Please also pay attention to information published by Renesas Technology Corp. by various means, including the Renesas Technology Corp. Semiconductor home page (http:// www.renesas.com). When using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and algorithms, please be sure to evaluate all information as a total system before making a final decision on the applicability of the information and products. Renesas Technology Corp. assumes no responsibility for any damage, liability or other loss resulting from the information contained herein. Renesas Technology Corp. semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human life is potentially at stake. Please contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor when considering the use of a product contained herein for any specific purposes, such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use. The prior written approval of Renesas Technology Corp. is necessary to reprint or reproduce in whole or in part these materials. If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government and cannot be imported into a country other than the approved destination. Any diversion or reexport contrary to the export control laws and regulations of Japan and/ or the country of destination is prohibited. Please contact Renesas Technology Corp. for further details on these materials or the products contained therein.
REVISION HISTORY
Rev. Date Page 1.00 Jan 14, 2005 - First edition issued
3804 Group (Spec. H) User's Manual
Description Summary
(1/1)
BEFORE USING THIS USER'S MANUAL
This user's manual consists of the following three chapters. Refer to the chapter appropriate to your conditions, such as hardware design or software development.
1. Organization
q CHAPTER 1 HARDWARE This chapter describes features of the microcomputer and operation of each peripheral function. q CHAPTER 2 APPLICATION This chapter describes usage and application examples of peripheral functions, based mainly on setting examples of relevant registers. q CHAPTER 3 APPENDIX This chapter includes necessary information for systems development using the microcomputer, such as the electrical characteristics, the notes, and the list of registers.
2. Structure of Register
The figure of each register structure describes its functions, contents at reset, and attributes as follows:
(Note 2)
Bits
b7 b6 b5 b4 b3 b2 b1 b0 0
Bit attributes
(Note 1)
Contents immediately after reset release
CPU mode register (CPUM) [Address : 003B16] b 0 1 2 3 4 5 6 7 Stack page selection bit Name Processor mode bits
b1 b0
Functions
0 0 : Single-chip mode 01: 1 0 : Not available 11: 0 : 0 page 1 : 1 page
At reset
RW
0 0 0 0 0 0

Nothing arranged for these bits. These are write disabled bits. When these bits are read out, the contents are "0." Fix this bit to "0. " Main clock division ratio selection bits
0 0 : = XIN/2 (High-speed mode) 0 1 : = XIN/8 (Middle-speed mode) 1 0 : = XIN/8 (Middle-speed mode) 1 1 : = XIN (Double-speed mode)
b7 b6
1 0
: Bit in which nothing is arranged
: Bit that is not used for control of the corresponding function
Notes 1: Contents immediately after reset release 0 ****** "0" at reset release 1 ****** "1" at reset release Undefined ****** Undefined or reset release ******Contents determined by option at reset release 2: Bit attributes******The attributes of control register bits are classified into 3 bytes : read-only, write-only and read and write. In the figure, these attributes are represented as follows : R******Read ******Read enabled ******Read disabled W******Write ******Write enabled ******Write disabled
3. Supplementary
For details of related development tools and documents, refer to web page "3804 Group" on our website (http://www.renesas.com/eng/products/mpumcu/8bit/38000/index.html).
Table of contents 3804 Group (Spec.H)
Table of contents
CHAPTER 1 HARDWARE
DESCRIPTION ................................................................................................................................ 1-2 FEATURES ...................................................................................................................................... 1-2 PIN CONFIGURATION .................................................................................................................. 1-3 FUNCTIONAL BLOCK .................................................................................................................. 1-4 PIN DESCRIPTION ........................................................................................................................ 1-5 PART NUMBERING ....................................................................................................................... 1-6 GROUP EXPANSION .................................................................................................................... 1-7 Memory Size ............................................................................................................................. 1-7 Packages ................................................................................................................................... 1-7 FUNCTIONAL DESCRIPTION ...................................................................................................... 1-8 CENTRAL PROCESSING UNIT (CPU) ................................................................................. 1-8 MEMORY ................................................................................................................................. 1-13 I/O PORTS .............................................................................................................................. 1-15 INTERRUPTS .......................................................................................................................... 1-23 TIMERS ................................................................................................................................... 1-27 SERIAL INTERFACE ............................................................................................................. 1-40 PULSE WIDTH MODULATION (PWM) ................................................................................ 1-54 A/D CONVERTER .................................................................................................................. 1-56 D/A CONVERTER .................................................................................................................. 1-58 WATCHDOG TIMER .............................................................................................................. 1-59 MULTI-MASTER I2C-BUS INTERFACE ............................................................................... 1-60 RESET CIRCUIT .................................................................................................................... 1-74 CLOCK GENERATING CIRCUIT ......................................................................................... 1-76 FLASH MEMORY MODE ...................................................................................................... 1-80 NOTES ON PROGRAMMING ..................................................................................................... 1-99 NOTES ON USAGE ................................................................................................................... 1-100 FUNCTIONAL DESCRIPTION SUPPLEMENT ....................................................................... 1-101 Interrupt ................................................................................................................................. 1-101 Timing After Interrupt ........................................................................................................... 1-102 A/D Converter ....................................................................................................................... 1-103
CHAPTER 2 APPLICATION
2.1 I/O port ..................................................................................................................................... 2-2 2.1.1 Memory map ................................................................................................................... 2-2 2.1.2 Relevant registers .......................................................................................................... 2-3 2.1.3 Port Pi pull-up control register ..................................................................................... 2-5 2.1.4 Terminate unused pins .................................................................................................. 2-5 2.1.5 Notes on I/O port ........................................................................................................... 2-6 2.1.6 Termination of unused pins .......................................................................................... 2-7 2.2 Interrupt ................................................................................................................................... 2-8 2.2.1 Memory map ................................................................................................................... 2-8 2.2.2 Relevant registers .......................................................................................................... 2-8 2.2.3 Interrupt source ............................................................................................................ 2-12 2.2.4 Interrupt operation ........................................................................................................ 2-13
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
i
Table of contents 3804 Group (Spec.H)
2.2.5 Interrupt control ............................................................................................................ 2-16 2.2.6 INT interrupt .................................................................................................................. 2-19 2.2.7 Notes on interrupts ...................................................................................................... 2-20 2.3 Timer ....................................................................................................................................... 2-22 2.3.1 Memory map ................................................................................................................. 2-22 2.3.2 Relevant registers ........................................................................................................ 2-23 2.3.3 Timer application examples ........................................................................................ 2-32 2.3.4 Notes on timer .............................................................................................................. 2-45 2.4 Serial interface ..................................................................................................................... 2-47 2.4.1 Memory map ................................................................................................................. 2-47 2.4.2 Relevant registers ........................................................................................................ 2-48 2.4.3 Serial I/O connection examples ................................................................................. 2-56 2.4.4 Setting of serial I/O transfer data format ................................................................. 2-58 2.4.5 Serial I/O1, serial I/O3 operation: stop and initialize .............................................. 2-59 2.4.6 Serial I/O pin function and selection method ........................................................... 2-60 2.4.7 Serial I/O application examples ................................................................................. 2-61 2.4.8 Notes on serial interface ............................................................................................. 2-81 2.5 Multi-master I 2C-BUS interface ......................................................................................... 2-84 2.5.1 Memory map ................................................................................................................. 2-84 2.5.2 Relevant registers ........................................................................................................ 2-85 2.5.3 I 2C-BUS overview ......................................................................................................... 2-94 2.5.4 Communication format ................................................................................................. 2-95 2.5.5 Synchronization and arbitration lost .......................................................................... 2-96 2.5.6 SMBUS communication usage example ................................................................... 2-98 2.5.7 Notes on multi-master I 2C-BUS interface ............................................................... 2-114 2.5.8 Notes on programming for SMBUS interface ......................................................... 2-117 2.6 PWM ...................................................................................................................................... 2-118 2.6.1 Memory map ............................................................................................................... 2-118 2.6.2 Relevant registers ...................................................................................................... 2-118 2.6.3 PWM output circuit application example ................................................................. 2-120 2.6.4 Notes on PWM ........................................................................................................... 2-122 2.7 A/D converter ..................................................................................................................... 2-123 2.7.1 Memory map ............................................................................................................... 2-123 2.7.2 Relevant registers ...................................................................................................... 2-123 2.7.3 A/D converter application examples ........................................................................ 2-127 2.7.4 Notes on A/D converter ............................................................................................ 2-131 2.8 D/A Converter ..................................................................................................................... 2-132 2.8.1 Memory map ............................................................................................................... 2-132 2.8.2 Relevant registers ...................................................................................................... 2-133 2.8.3 D/A converter application example .......................................................................... 2-135 2.8.4 Notes on D/A converter ............................................................................................ 2-138 2.9 Watchdog timer .................................................................................................................. 2-139 2.9.1 Memory map ............................................................................................................... 2-139 2.9.2 Relevant registers ...................................................................................................... 2-139 2.9.3 Watchdog timer application examples ..................................................................... 2-141 2.9.4 Notes on watchdog timer .......................................................................................... 2-142 2.10 Reset .................................................................................................................................. 2-143 2.10.1 Connection example of reset IC ............................................................................ 2-143 ____________ 2.10.2 Notes on RESET pin ............................................................................................... 2-144 2.11 Clock generating circuit ................................................................................................ 2-145 2.11.1 Relevant registers .................................................................................................... 2-145 2.11.2 Clock generating circuit application example ....................................................... 2-146
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
ii
Table of contents 3804 Group (Spec.H)
2.12 Standby function ............................................................................................................. 2-149 2.12.1 Stop mode ................................................................................................................. 2-149 2.12.2 Wait mode ................................................................................................................. 2-153 2.13 Flash memory mode ....................................................................................................... 2-156 2.13.1 Overview .................................................................................................................... 2-156 2.13.2 Memory map ............................................................................................................. 2-156 2.13.3 Relevant registers .................................................................................................... 2-157 2.13.4 Parallel I/O mode ..................................................................................................... 2-159 2.13.5 Standard serial I/O mode ........................................................................................ 2-159 2.13.6 CPU rewrite mode ................................................................................................... 2-160 2.13.7 Flash memory mode application examples .......................................................... 2-162 2.13.8 Notes on CPU rewrite mode .................................................................................. 2-166
CHAPTER 3 APPENDIX
3.1 ELECTRICAL CHARACTERISTICS ...................................................................................... 3-2 3.1.1 Absolute maximum ratings ............................................................................................ 3-2 3.1.2 Recommended operating conditions ............................................................................ 3-3 3.1.3 Electrical characteristics ................................................................................................ 3-6 3.1.4 A/D converter characteristics ........................................................................................ 3-8 3.1.5 D/A converter characteristics ........................................................................................ 3-8 3.1.6 Power source circuit timing characteristics ................................................................ 3-8 3.1.7 Timing requirements and switching characteristics ................................................... 3-9 3.1.8 Multi-master I 2C-BUS bus line characteristics .......................................................... 3-14 3.2 Standard characteristics .................................................................................................... 3-15 3.2.1 Power source current standard characteristics ........................................................ 3-15 3.2.2 Port standard characteristics ...................................................................................... 3-19 3.2.3 A/D conversion standard characteristics ................................................................... 3-22 3.2.4 D/A conversion standard characteristics ................................................................... 3-26 3.3 Notes on use ........................................................................................................................ 3-27 3.3.1 Notes on input and output ports ................................................................................ 3-27 3.3.2 Termination of unused pins ........................................................................................ 3-28 3.3.3 Notes on interrupts ...................................................................................................... 3-29 3.3.4 Notes on 8-bit timer (timer 1, 2, X, Y) ..................................................................... 3-30 3.3.5 Notes on 16-bit timer (timer Z) .................................................................................. 3-30 3.3.6 Notes on serial interface ............................................................................................. 3-32 3.3.7 Notes on multi-master I 2C-BUS interface ................................................................. 3-34 3.3.8 Notes on programming for SMBUS interface ........................................................... 3-36 3.3.9 Notes on PWM ............................................................................................................. 3-37 3.3.10 Notes on A/D converter ............................................................................................ 3-37 3.3.11 Notes on D/A converter ............................................................................................ 3-38 3.3.12 Notes on watchdog timer .......................................................................................... 3-38 ____________ 3.3.13 Notes on RESET pin ................................................................................................. 3-38 3.3.14 Notes on low-speed operation mode ...................................................................... 3-38 3.3.15 Quartz-crystal oscillator ............................................................................................. 3-39 3.3.16 Notes on restarting oscillation .................................................................................. 3-39 3.3.17 Notes on using stop mode ....................................................................................... 3-39 3.3.18 Notes on wait mode .................................................................................................. 3-40 3.3.19 Notes on CPU rewrite mode .................................................................................... 3-40 3.3.20 Notes on programming .............................................................................................. 3-40 3.3.21 Notes on flash memory version ............................................................................... 3-42
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
iii
Table of contents 3804 Group (Spec.H)
3.3.22 Notes on electric characteristic differences between mask ROM and flash nemory version MCUs ............................................................................................................. 3-42 3.3.23 Notes on handling of power source pins ............................................................... 3-42 3.3.24 Power Source Voltage ............................................................................................... 3-42 3.4 Countermeasures against noise ...................................................................................... 3-43 3.4.1 Shortest wiring length .................................................................................................. 3-43 3.4.2 Connection of bypass capacitor across VSS line and VCC line ............................... 3-45 3.4.3 Wiring to analog input pins ........................................................................................ 3-46 3.4.4 Oscillator concerns ....................................................................................................... 3-47 3.4.5 Setup for I/O ports ....................................................................................................... 3-48 3.4.6 Providing of watchdog timer function by software .................................................. 3-49 3.5 Control registers .................................................................................................................. 3-50 3.6 Package outline ................................................................................................................... 3-80 3.7 Machine instructions .......................................................................................................... 3-82 3.8 List of instruction code ..................................................................................................... 3-93 3.9 SFR memory map ................................................................................................................ 3-94 3.10 Pin configurations ............................................................................................................. 3-95
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
iv
List of figures 3804 Group (Spec.H)
List of figures
CHAPTER 1 HARDWARE
Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. 1 3804 group (Spec. H) pin configuration ........................................................................ 1-3 2 3804 group (Spec. H) pin configuration ........................................................................ 1-3 3 Functional block diagram ................................................................................................. 1-4 4 Part numbering .................................................................................................................. 1-6 5 Memory expansion plan ................................................................................................... 1-7 6 740 Family CPU register structure ................................................................................. 1-8 7 Register push and pop at interrupt generation and subroutine call .......................... 1-9 8 Structure of CPU mode register ................................................................................... 1-11 9 Structure of MISRG ........................................................................................................ 1-12 10 Memory map diagram ................................................................................................... 1-13 11 Memory map of special function register (SFR) ...................................................... 1-14 12 Port block diagram (1) ................................................................................................. 1-16 13 Port block diagram (2) ................................................................................................. 1-17 14 Port block diagram (3) ................................................................................................. 1-18 15 Structure of port pull-up control register (1) ............................................................. 1-19 16 Structure of port pull-up control register (2) ............................................................. 1-20 17 Structure of port pull-up control register (3) ............................................................. 1-21 18 Structure of port pull-up control register (4) ............................................................. 1-22 19 Interrupt control ............................................................................................................. 1-25 20 Structure of interrupt-related registers ....................................................................... 1-26 21 Block diagram of timer X, timer Y, timer 1, and timer 2 ........................................ 1-29 22 Structure of timer XY mode register .......................................................................... 1-30 23 Structure of timer 12, X and timer Y, Z count source selection registers ........... 1-31 24 Block diagram of timer Z ............................................................................................. 1-35 25 Structure of timer Z mode register ............................................................................. 1-36 26 Timing chart of timer/event counter mode ................................................................ 1-37 27 Timing chart of pulse output mode ............................................................................ 1-37 28 Timing chart of pulse period measurement mode (Measuring term between two rising edges) .. 1-38 29 Timing chart of pulse width measurement mode (Measuring "L" term) ................ 1-38 30 Timing chart of programmable waveform generating mode ................................... 1-39 31 Timing chart of programmable one-shot generating mode ("H" one-shot pulse generating) ... 1-39 32 Block diagram of clock synchronous serial I/O1 ...................................................... 1-40 33 Operation of clock synchronous serial I/O1 .............................................................. 1-40 34 Block diagram of UART serial I/O1 ............................................................................ 1-41 35 Operation of UART serial I/O1 ................................................................................... 1-41 36 Structure of serial I/O1 control registers ................................................................... 1-43 37 Structure of serial I/O2 control register ..................................................................... 1-46 38 Block diagram of serial I/O2 ....................................................................................... 1-46 39 Timing of serial I/O2 ..................................................................................................... 1-47 40 Block diagram of clock synchronous serial I/O3 ...................................................... 1-48 41 Operation of clock synchronous serial I/O3 .............................................................. 1-48 42 Block diagram of UART serial I/O3 ............................................................................ 1-49 43 Operation of UART serial I/O3 ................................................................................... 1-49 44 Structure of serial I/O3 control registers ................................................................... 1-51 45 Timing of PWM period ................................................................................................. 1-54 46 Block diagram of PWM function ................................................................................. 1-54
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
v
List of figures 3804 Group (Spec.H)
Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig.
47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96
Structure of PWM control register .............................................................................. 1-55 PWM output timing when PWM register or PWM prescaler is changed .............. 1-55 Structure of AD/DA control register ........................................................................... 1-56 Structure of 10-bit A/D mode reading ........................................................................ 1-56 Block diagram of A/D converter .................................................................................. 1-57 Block diagram of D/A converter .................................................................................. 1-58 Equivalent connection circuit of D/A converter (DA1) ............................................. 1-58 Block diagram of Watchdog timer .............................................................................. 1-59 Structure of Watchdog timer control register ............................................................ 1-59 Block diagram of multi-master I 2C-BUS interface .................................................... 1-60 Structure of I 2C slave address registers 0 to 2 ....................................................... 1-61 Structure of I 2C clock control register ........................................................................ 1-62 Structure of I 2C control register .................................................................................. 1-63 Structure of I2C status register ................................................................................... 1-65 Interrupt request signal generating timing ................................................................. 1-65 START condition generating timing diagram ............................................................ 1-66 STOP condition generating timing diagram ............................................................... 1-66 START/STOP condition detecting timing diagram .................................................... 1-67 STOP condition detecting timing diagram ................................................................. 1-67 Structure of I2C START/STOP condition control register ........................................ 1-68 Structure of I 2C special mode status register ........................................................... 1-69 Structure of I 2C special mode control register ......................................................... 1-70 Address data communication format .......................................................................... 1-71 Reset circuit example ................................................................................................... 1-74 Reset sequence ............................................................................................................ 1-74 Internal status at reset ................................................................................................. 1-75 Ceramic resonator circuit ............................................................................................. 1-77 External clock input circuit .......................................................................................... 1-77 System clock generating circuit block diagram ........................................................ 1-78 State transitions of system clock ................................................................................ 1-79 Block diagram of built-in flash memory ..................................................................... 1-81 Structure of flash memory control register 0 ............................................................ 1-82 Structure of flash memory control register 1 ............................................................ 1-82 Structure of flash memory control register 2 ............................................................ 1-83 CPU rewrite mode set/release flowchart ................................................................... 1-83 Program flowchart ......................................................................................................... 1-85 Erase flowchart .............................................................................................................. 1-86 Full status check flowchart and remedial procedure for errors ............................. 1-88 Structure of ROM code protect control address ...................................................... 1-89 ID code store addresses .............................................................................................. 1-90 Connection for standard serial I/O mode 1 (M38049FFHFP/HP/KP) .................... 1-94 Connection for standard serial I/O mode 2 (M38049FFHFP/HP/KP) .................... 1-95 Connection for standard serial I/O mode 1 (M38049FFHSP) ................................ 1-96 Connection for standard serial I/O mode 2 (M38049FFHSP) ................................ 1-97 Operating waveform for standard serial I/O mode 1 ............................................... 1-98 Operating waveform for standard serial I/O mode 2 ............................................... 1-98 Timing chart after an interrupt occurs ..................................................................... 1-102 Time up to execution of the interrupt processing routine ..................................... 1-102 A/D conversion equivalent circuit ............................................................................. 1-104 A/D conversion timing chart ...................................................................................... 1-105
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
vi
List of figures 3804 Group (Spec.H)
CHAPTER 2 APPLICATION
Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. 2.1.1 Memory map of I/O port relevant registers .............................................................. 2-2 2.1.2 Structure of Port Pi (i = 0 to 6) ................................................................................. 2-3 2.1.3 Structure of Port Pi direction register (i = 0 to 6) .................................................. 2-3 2.1.4 Structure of Port Pi pull-up control register (i = 0, 1, 2, 4, 5, 6) ......................... 2-4 2.1.5 Structure of Port P3 pull-up control register ............................................................ 2-4 2.2.1 Memory map of registers relevant to interrupt ........................................................ 2-8 2.2.2 Structure of Interrupt source selection register ....................................................... 2-8 2.2.3 Structure of Interrupt edge selection register .......................................................... 2-9 2.2.4 Structure of Interrupt request register 1 ................................................................... 2-9 2.2.5 Structure of Interrupt request register 2 ................................................................. 2-10 2.2.6 Structure of Interrupt control register 1 .................................................................. 2-10 2.2.7 Structure of Interrupt control register 2 .................................................................. 2-11 2.2.8 Interrupt operation diagram ....................................................................................... 2-13 2.2.9 Changes of stack pointer and program counter upon acceptance of interrupt request .... 2-14 2.2.10 Time up to execution of interrupt processing routine ......................................... 2-15 2.2.11 Timing chart after acceptance of interrupt request ............................................. 2-15 2.2.12 Interrupt control diagram ......................................................................................... 2-16 2.2.13 Example of multiple interrupts ................................................................................ 2-18 2.2.14 Sequence of changing relevant register ............................................................... 2-20 2.2.15 Sequence of check of interrupt request bit .......................................................... 2-21 2.3.1 Memory map of registers relevant to timers .......................................................... 2-22 2.3.2 Structure of Prescaler 12, Prescaler X, Prescaler Y ............................................ 2-23 2.3.3 Structure of Timer 1 .................................................................................................. 2-23 2.3.4 Structure of Timer 2, Timer X, Timer Y ................................................................. 2-24 2.3.5 Structure of Timer Z (low-order, high-order) .......................................................... 2-24 2.3.6 Structure of Timer XY mode register ...................................................................... 2-25 2.3.7 Structure of Timer Z mode register ......................................................................... 2-26 2.3.8 Structure of Timer 12, X count source selection register .................................... 2-28 2.3.9 Structure of Timer Y, Z count source selection register ...................................... 2-28 2.3.10 Structure of Interrupt source selection register ................................................... 2-29 2.3.11 Structure of Interrupt request register 1 ............................................................... 2-30 2.3.12 Structure of Interrupt request register 2 ............................................................... 2-30 2.3.13 Structure of Interrupt control register 1 ................................................................ 2-31 2.3.14 Structure of Interrupt control register 2 ................................................................ 2-31 2.3.15 Timers connection and setting of division ratios ................................................. 2-33 2.3.16 Relevant registers setting ....................................................................................... 2-33 2.3.17 Control procedure ..................................................................................................... 2-34 2.3.18 Peripheral circuit example ....................................................................................... 2-35 2.3.19 Timers connection and setting of division ratios ................................................. 2-35 2.3.20 Relevant registers setting ....................................................................................... 2-36 2.3.21 Control procedure ..................................................................................................... 2-37 2.3.22 Judgment method of valid/invalid of input pulses ............................................... 2-38 2.3.23 Relevant registers setting ....................................................................................... 2-39 2.3.24 Control procedure ..................................................................................................... 2-40 2.3.25 Timers connection and setting of division ratios ................................................. 2-41 2.3.26 Relevant registers setting ....................................................................................... 2-42 2.3.27 Control procedure (1) .............................................................................................. 2-43 2.3.28 Control procedure (2) .............................................................................................. 2-44 2.4.1 Memory map of registers relevant to Serial I/O .................................................... 2-47 2.4.2 Structure of Transmit/Receive buffer register 1 and Transmit/Receive buffer register 3 .. 2-48
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
vii
List of figures 3804 Group (Spec.H)
Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig.
2.4.3 Structure of Serial I/O1 status register and Serial I/O3 status register ............. 2-48 2.4.4 Structure of Serial I/O1 control register .................................................................. 2-49 2.4.5 Structure of Serial I/O3 control register .................................................................. 2-50 2.4.6 Structure of UART1 control register ........................................................................ 2-51 2.4.7 Structure of UART3 control register ........................................................................ 2-51 2.4.8 Structure of Baud rate generator 1 and Baud rate generator 3 ......................... 2-52 2.4.9 Structure of Serial I/O2 control register .................................................................. 2-52 2.4.10 Structure of Serial I/O2 register ............................................................................. 2-53 2.4.11 Structure of Interrupt source selection register ................................................... 2-53 2.4.12 Structure of Interrupt request register 1 ............................................................... 2-54 2.4.13 Structure of Interrupt request register 2 ............................................................... 2-54 2.4.14 Structure of Interrupt control register 1 ................................................................ 2-55 2.4.15 Structure of Interrupt control register 2 ................................................................ 2-55 2.4.16 Serial I/O connection examples (1) ....................................................................... 2-56 2.4.17 Serial I/O connection examples (2) ....................................................................... 2-57 2.4.18 Serial I/O transfer data format ............................................................................... 2-58 2.4.19 Connection diagram ................................................................................................. 2-61 2.4.20 Timing chart (using clock synchronous serial I/O) .............................................. 2-61 2.4.21 Registers setting relevant to transmitting side ..................................................... 2-62 2.4.22 Registers setting relevant to receiving side ......................................................... 2-63 2.4.23 Control procedure of transmitting side .................................................................. 2-64 2.4.24 Control procedure of receiving side ...................................................................... 2-65 2.4.25 Connection diagrams ............................................................................................... 2-66 2.4.26 Timing chart (serial I/O1) ........................................................................................ 2-66 2.4.27 Registers setting relevant to serial I/O1 ............................................................... 2-67 2.4.28 Setting of serial I/O1 transmission data ............................................................... 2-67 2.4.29 Control procedure of serial I/O1 ............................................................................ 2-68 2.4.30 Registers setting relevant to serial I/O2 ............................................................... 2-69 2.4.31 Setting of serial I/O2 transmission data ............................................................... 2-69 2.4.32 Control procedure of serial I/O2 ............................................................................ 2-70 2.4.33 Connection diagram ................................................................................................. 2-71 2.4.34 Timing chart .............................................................................................................. 2-72 2.4.35 Relevant registers setting ....................................................................................... 2-72 2.4.36 Control procedure of master unit ........................................................................... 2-73 2.4.37 Control procedure of slave unit ............................................................................. 2-74 2.4.38 Connection diagram (Communication using UART) ............................................ 2-75 2.4.39 Timing chart (using UART) ..................................................................................... 2-75 2.4.40 Registers setting relevant to transmitting side ..................................................... 2-77 2.4.41 Registers setting relevant to receiving side ......................................................... 2-78 2.4.42 Control procedure of transmitting side .................................................................. 2-79 2.4.43 Control procedure of receiving side ...................................................................... 2-80 2.4.44 Sequence of setting serial I/Oi (i = 1, 3) control register again ....................... 2-82 2.5.1 Memory map of registers relevant to I2C-BUS interface ...................................... 2-84 2.5.2 Structure of MISRG ................................................................................................... 2-85 2.5.3 Structure of I2C data shift register ........................................................................... 2-85 2.5.4 Structure of I 2C special mode status register ........................................................ 2-86 2.5.5 Structure of I 2C status register ................................................................................. 2-87 2.5.6 Structure of I2C control register ............................................................................... 2-88 2.5.7 Structure of I2C clock control register ..................................................................... 2-89 2.5.8 Structure of I2C START/STOP condition control register ..................................... 2-90 2.5.9 Structure of I 2C special mode control register ....................................................... 2-90 2.5.10 Structure of I2C slave address register i (i = 0 to 2) ......................................... 2-91
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
viii
List of figures 3804 Group (Spec.H)
Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig.
2.5.11 Structure of Interrupt source selection register ................................................... 2-91 2.5.12 Structure of Interrupt request register 1 ............................................................... 2-92 2.5.13 Structure of Interrupt request register 2 ............................................................... 2-92 2.5.14 Structure of Interrupt control register 1 ................................................................ 2-93 2.5.15 Structure of Interrupt control register 2 ................................................................ 2-93 2.5.16 I2C-BUS connection structure ................................................................................. 2-94 2.5.17 I2C-BUS communication format example .............................................................. 2-95 2.5.18 RESTART condition of master reception .............................................................. 2-96 2.5.19 SCL waveforms when synchronizing clocks ......................................................... 2-97 2.5.20 Initial setting example for SMBUS communication .............................................. 2-99 2.5.21 Read Word protocol communication as SMBUS master device ..................... 2-100 2.5.22 Generating of START condition and transmission process of slave address + write bit ... 2-101 2.5.23 Transmission process of command ..................................................................... 2-102 2.5.24 Transmission process of RESTART condition and slave address + read bit ... 2-103 2.5.25 Reception process of lower data ......................................................................... 2-104 2.5.26 Reception process of upper data ........................................................................ 2-105 2.5.27 Generating of STOP condition ............................................................................. 2-106 2.5.28 Communication example as SMBUS slave device ............................................ 2-107 2.5.29 Reception process of START condition and slave address ............................ 2-108 2.5.30 Reception process of command ........................................................................... 2-109 2.5.31 Reception process of RESTART condition and slave address ....................... 2-110 2.5.32 Transmission process of lower data .................................................................... 2-111 2.5.33 Transmission process of upper data ................................................................... 2-112 2.5.34 Reception of STOP condition ............................................................................... 2-113 2.6.1 Memory map of registers relevant to PWM ......................................................... 2-118 2.6.2 Structure of PWM control register ......................................................................... 2-118 2.6.3 Structure of PWM prescaler ................................................................................... 2-119 2.6.4 Structure of PWM register ...................................................................................... 2-119 2.6.5 Connection diagram ................................................................................................. 2-120 2.6.6 PWM output timing ................................................................................................... 2-120 2.6.7 Setting of relevant registers ................................................................................... 2-121 2.6.8 PWM output .............................................................................................................. 2-121 2.6.9 Control procedure ..................................................................................................... 2-122 2.7.1 Memory map of registers relevant to A/D converter ........................................... 2-123 2.7.2 Structure of AD/DA control register ....................................................................... 2-123 2.7.3 Structure of AD conversion register 1 .................................................................. 2-124 2.7.4 Structure of AD conversion register 2 .................................................................. 2-124 2.7.5 Structure of Interrupt source selection register ................................................... 2-125 2.7.6 Structure of Interrupt request register 2 ............................................................... 2-126 2.7.7 Structure of Interrupt control register 2 ................................................................ 2-126 2.7.8 Connection diagram ................................................................................................. 2-127 2.7.9 Relevant registers setting ....................................................................................... 2-127 2.7.10 Control procedure (10-bit A/D mode) .................................................................. 2-128 2.7.11 Connection diagram ............................................................................................... 2-129 2.7.12 Relevant registers setting ..................................................................................... 2-129 2.7.13 Control procedure (8-bit A/D mode) .................................................................... 2-130 2.8.1 Memory map of registers relevant to D/A converter ........................................... 2-132 2.8.2 Structure of Port P5 direction register .................................................................. 2-133 2.8.3 Structure of AD/DA control register ....................................................................... 2-133 2.8.4 Structure of DAi converter register ........................................................................ 2-134 2.8.5 Peripheral circuit example ....................................................................................... 2-135 2.8.6 Speaker output example ......................................................................................... 2-135
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
ix
List of figures 3804 Group (Spec.H)
Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig.
2.8.7 Relevant registers setting ....................................................................................... 2-136 2.8.8 Control procedure ..................................................................................................... 2-137 2.9.1 Memory map of registers relevant to watchdog timer ........................................ 2-139 2.9.2 Structure of Watchdog timer control register ....................................................... 2-139 2.9.3 Structure of CPU mode register ............................................................................ 2-140 2.9.4 Watchdog timer connection and division ratio setting ........................................ 2-141 2.9.5 Relevant registers setting ....................................................................................... 2-142 2.9.6 Control procedure ..................................................................................................... 2-142 2.10.1 Example of poweron reset circuit ........................................................................ 2-143 2.10.2 RAM backup system .............................................................................................. 2-143 2.11.1 Structure of CPU mode register .......................................................................... 2-145 2.11.2 Connection diagram ............................................................................................... 2-146 2.11.3 Status transition diagram during power failure .................................................. 2-146 2.11.4 Setting of relevant registers ................................................................................. 2-147 2.11.5 Control procedure ................................................................................................... 2-148 2.12.1 Oscillation stabilizing time at restoration by reset input .................................. 2-150 2.12.2 Execution sequence example at restoration by occurrence of INT0 interrupt request ... 2-152 2.12.3 Reset input time ..................................................................................................... 2-154 2.13.1 Memory map of M38049FFHSP/FP/HP/KP ........................................................ 2-156 2.13.2 Memory map of registers relevant to flash memory ......................................... 2-157 2.13.3 Structure of Flash memory control register 0 .................................................... 2-157 2.13.4 Structure of Flash memory control register 1 .................................................... 2-158 2.13.5 Structure of Flash memory control register 2 .................................................... 2-158 2.13.6 Rewrite example of built-in flash memory in standard serial I/O mode ......... 2-162 2.13.7 Connection example in standard serial I/O mode (1) ....................................... 2-163 2.13.8 Connection example in standard serial I/O mode (2) ....................................... 2-163 2.13.9 Connection example in standard serial I/O mode (3) ....................................... 2-164 2.13.10 Example of rewrite system for built-in flash memory in CPU rewrite mode (singlechip mode) ............................................................................................................ 2-165
CHAPTER 3 APPENDIX
Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Circuit for measuring output switching characteristics (1) ................................... 3-12 Circuit for measuring output switching characteristics (2) ................................... 3-12 Timing diagram (in single-chip mode) ..................................................................... 3-13 Timing diagram of multi-master I 2C-BUS ................................................................ 3-14 Power source current standard characteristics (in high-speed mode) ............... 3-15 Power source current standard characteristics (in middle-speed mode) ........... 3-15 Power source current standard characteristics (in low-speed mode) ................. 3-16 Power source current standard characteristics (in high-speed mode, f(XIN) = 16.8 MHz, WAIT state) ....................................................................................................... 3-16 3.2.5 Power source current standard characteristics (in middle-speed mode, f(XIN) = 16.8 MHz, WAIT state) ....................................................................................................... 3-17 3.2.6 Power source current standard characteristics (in low-speed mode, WAIT state) ...... 3-17 3.2.7 Power source current standard characteristics (in high-speed mode, f(XIN) = 16.8 MHz, A/D converter operating) ................................................................................. 3-18 3.2.8 Power source current standard characteristics (at oscillation stopping) ............ 3-18 3.2.9 CMOS output port P-channel side characteristics (Ta = 25 C) ......................... 3-19 3.2.10 CMOS output port N-channel side characteristics (Ta = 25 C) ...................... 3-19 3.2.11 N-channel open-drain output port N-channel side characteristics (Ta = 25 C) .... 3-20 3.2.12 CMOS large current output port N-channel side characteristics (Ta = 25 C) .... 3-20 3.2.13 CMOS input port at pull-up characteristics (Ta = 25 C) .................................. 3-21 3.1.1 3.1.2 3.1.3 3.1.4 3.2.1 3.2.2 3.2.3 3.2.4
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
x
List of figures 3804 Group (Spec.H)
Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig.
3.2.14 A/D conversion standard characteristics (f(XIN) = 8 MHz) ................................. 3-23 3.2.15 A/D conversion standard characteristics (f(XIN) = 12 MHz) ............................... 3-24 3.2.16 A/D conversion standard characteristics (f(XIN) = 16 MHz) ............................... 3-25 3.2.17 D/A conversion standard characteristics ............................................................... 3-26 3.3.1 Sequence of changing relevant register ................................................................. 3-29 3.3.2 Sequence of check of interrupt request bit ............................................................ 3-30 3.3.3 Sequence of setting serial I/Oi (i = 1, 3) control register again ......................... 3-33 3.3.4 Ceramic resonator circuit .......................................................................................... 3-38 3.3.5 Initialization of processor status register ................................................................ 3-40 3.3.6 Sequence of PLP instruction execution .................................................................. 3-41 3.3.7 Stack memory contents after PHP instruction execution ..................................... 3-41 3.3.8 Status flag at decimal calculations .......................................................................... 3-41 _____________ 3.4.1 Wiring for the RESET pin ......................................................................................... 3-43 3.4.2 Wiring for clock I/O pins ........................................................................................... 3-44 3.4.3 Wiring for CNVSS pin .................................................................................................. 3-44 3.4.4 Bypass capacitor across the VSS line and the VCC line ........................................ 3-45 3.4.5 Analog signal line and a resistor and a capacitor ................................................ 3-46 3.4.6 Wiring for a large current signal line ...................................................................... 3-47 3.4.7 Wiring of signal lines where potential levels change frequently ......................... 3-47 3.4.8 VSS pattern on the underside of an oscillator ........................................................ 3-48 3.4.9 Setup for I/O ports ..................................................................................................... 3-48 3.4.10 Watchdog timer by software ................................................................................... 3-49 3.5.1 Structure of Port Pi .................................................................................................... 3-50 3.5.2 Structure of Port Pi direction register ..................................................................... 3-50 3.5.3 Structure of Timer 12, X count source selection register .................................... 3-51 3.5.4 Structure of Timer Y, Z count source selection register ...................................... 3-52 3.5.5 Structure of MISRG ................................................................................................... 3-53 3.5.6 Structure of I2C data shift register ........................................................................... 3-53 3.5.7 Structure of I2C special mode status register ........................................................ 3-54 3.5.8 Structure of I2C status register................................................................................. 3-55 3.5.9 Structure of I2C control register ............................................................................... 3-56 3.5.10 Structure of I2C clock control register ................................................................... 3-57 3.5.11 Structure of I2C START/STOP condition control register ................................... 3-58 3.5.12 Structure of I2C special mode control register ..................................................... 3-58 3.5.13 Structure of Transmit/Receive buffer register 1, Transmit/Receive buffer register 3 .... 3-59 3.5.14 Structure of Serial I/O1 status register, Serial I/O3 status register ................. 3-59 3.5.15 Structure of Serial I/O1 control register ................................................................ 3-60 3.5.16 Structure of UART1 control register ...................................................................... 3-61 3.5.17 Structure of Baud rate generator i ........................................................................ 3-61 3.5.18 Structure of Serial I/O2 control register ................................................................ 3-62 3.5.19 Structure of Watchdog timer control register ....................................................... 3-62 3.5.20 Structure of Serial I/O2 register ............................................................................. 3-63 3.5.21 Structure of Prescaler 12, Prescaler X, Prescaler Y .......................................... 3-63 3.5.22 Structure of Timer 1 ................................................................................................ 3-64 3.5.23 Structure of Timer 2, Timer X, Timer Y ............................................................... 3-64 3.5.24 Structure of Timer XY mode register .................................................................... 3-65 3.5.25 Structure of Timer Z low-order, Timer Z high-order ........................................... 3-66 3.5.26 Structure of Timer Z mode register ....................................................................... 3-66 3.5.27 Structure of PWM control register ......................................................................... 3-68 3.5.28 Structure of PWM prescaler ................................................................................... 3-68 3.5.29 Structure of PWM register ...................................................................................... 3-68 3.5.30 Structure of Serial I/O3 control register ................................................................ 3-69
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
xi
List of figures 3804 Group (Spec.H)
Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig. Fig.
3.5.31 3.5.32 3.5.33 3.5.34 3.5.35 3.5.36 3.5.37 3.5.38 3.5.39 3.5.40 3.5.41 3.5.42 3.5.43 3.5.44 3.5.45 3.5.46 3.5.47 3.5.48
Structure Structure Structure Structure Structure Structure Structure Structure Structure Structure Structure Structure Structure Structure Structure Structure Structure Structure
of of of of of of of of of of of of of of of of of of
UART3 control register ...................................................................... 3-70 AD/DA control register ....................................................................... 3-70 AD conversion register 1 .................................................................. 3-71 DAi conversion register (i = 1, 2) .................................................... 3-71 AD conversion register 2 .................................................................. 3-71 Interrupt source selection register ................................................... 3-72 Interrupt edge selection register ...................................................... 3-73 CPU mode register ............................................................................ 3-73 Interrupt request register 1 ............................................................... 3-74 Interrupt request register 2 ............................................................... 3-74 Interrupt control register 1 ................................................................ 3-75 Interrupt control register 2 ................................................................ 3-75 Flash memory control register 0 ...................................................... 3-76 Flash memory control register 1 ...................................................... 3-77 Flash memory control register 2 ...................................................... 3-77 Port Pi pull-up control register (i = 0 to 2, 4 to 6) ....................... 3-78 Port P3 pull-up control register ........................................................ 3-78 I2C slave address register i (i = 0 to 2) ......................................... 3-79
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
xii
List of tables 3804 Group (Spec.H)
List of tables
CHAPTER 1 HARDWARE
Table Table Table Table Table Table Table Table Table Table Table Table Table Table Table Table Table Table Table Table Table Table Table 1 Support products ............................................................................................................ 1-2 2 Pin description ................................................................................................................ 1-5 3 Push and pop instructions of accumulator or processor status register ............... 1-9 4 Set and clear instructions of each bit of processor status register ..................... 1-10 5 I/O port function ........................................................................................................... 1-15 6 Interrupt vector addresses and priority ..................................................................... 1-24 7 Multi-master I2C-BUS interface functions .................................................................. 1-60 8 Set values of I 2C clock control register and SCL frequency ................................. 1-62 9 START condition generating timing table ................................................................. 1-66 10 STOP condition generating timing table ................................................................. 1-66 11 START condition/STOP condition detecting conditions ........................................ 1-67 12 Recommended set value to START/STOP condition set bits (SSC4-SSC0) for each oscillation frequency .................................................................................................. 1-68 13 Summary of 3804 group (spec. H) ......................................................................... 1-80 14 State of E/W inhibition function ............................................................................... 1-83 15 List of software commands (CPU rewrite mode) .................................................. 1-85 16 Definition of each bit in status register .................................................................. 1-87 17 Description of pin function (Flash Memory Serial I/O Mode 1) .......................... 1-93 18 Description of pin function (Flash Memory Serial I/O Mode 2) .......................... 1-93 19 Interrupt sources, vector addresses and priority ................................................. 1-101 20 Relative formula for a reference voltage VREF of A/D converter and Vref (at 10-bit A/ D mode) .................................................................................................................... 1-103 21 Relative formula for a reference voltage VREF of A/D converter and Vref (at 8-bit A/ D mode) .................................................................................................................... 1-103 22 Change of AD conversion register during A/D conversion (at 10-bit A/D mode) . 1-103 23 Change of AD conversion register during A/D conversion (at 8-bit A/D mode) ... 1-104
CHAPTER 2 APPLICATION
Table Table Table Table Table Table Table Table Table Table Table Table 2.1.1 Termination of unused pins (in single-chip mode) ............................................... 2-5 2.2.1 Interrupt sources, vector addresses and priority .............................................. 2-12 2.2.2 List of interrupt bits according to interrupt source ............................................. 2-17 2.3.1 CNTR0/CNTR1 active edge switch bit function .................................................... 2-25 2.3.2 CNTR2 active edge switch bit function ................................................................ 2-27 2.4.1 Pin function in clock synchronous serial I/O mode ............................................ 2-60 2.4.2 Pin function in UART mode ................................................................................... 2-60 2.4.3 Pin function in clock synchronous serial I/O mode ............................................ 2-60 2.4.4 Setting examples of Baud rate generator (BRG) values and transfer bit rate values ... 2-76 2.12.1 State in stop mode ............................................................................................. 2-149 2.12.2 State in wait mode .............................................................................................. 2-153 2.13.1 Parallel unit when parallel programming (when using EFP-I provided by Suisei Electronics System Co., Ltd.) ............................................................................ 2-159 Table 2.13.2 Connection example to programmer when serial programming (4 wires) .. 2-159
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
xiii
List of tables 3804 Group (Spec.H)
CHAPTER 3 APPENDIX
Table Table Table Table Table Table Table Table Table Table Table Table Table Table Table Table 3.1.1 Absolute maximum ratings ....................................................................................... 3-2 3.1.2 Recommended operating conditions (1) ................................................................ 3-3 3.1.3 Recommended operating conditions (2) ................................................................ 3-4 3.1.4 Recommended operating conditions (3) ............................................................... .3-5 3.1.5 Electrical characteristics (1) ..................................................................................... 3-6 3.1.6 Electrical characteristics (2) ..................................................................................... 3-7 3.1.7 A/D converter recommended operating conditions ............................................... 3-8 3.1.8 A/D converter characteristics ................................................................................... 3-8 3.1.9 D/A converter characteristics ................................................................................... 3-8 3.1.10 Power source circuit timing characteristics ......................................................... 3-8 3.1.11 Timing requirements (1) ......................................................................................... 3-9 3.1.12 Timing requirements (2) ....................................................................................... 3-10 3.1.13 Switching characteristics ...................................................................................... 3-11 3.1.14 Multi-master I 2C-BUS bus line characteristics .................................................. 3-14 3.5.1 CNTR0/CNTR1 active edge switch bit function .................................................... 3-65 3.5.2 CNTR2 active edge switch bit function ................................................................ 3-67
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
xiv
CHAPTER 1 HARDWARE
DESCRIPTION FEATURES PIN CONFIGURATION FUNCTIONAL BLOCK PIN DESCRIPTION PART NUMBERING GROUP EXPANSION FUNCTIONAL DESCRIPTION NOTES ON PROGRAMMING NOTES ON USAGE DATA REQUIRED FOR MASK ORDERS FUNCTIONAL DESCRIPTION SUPPLEMENT
HARDWARE 3804 Group (Spec.H) DESCRIPTION/FEATURES
DESCRIPTION
The 3804 group (Spec. H) is the 8-bit microcomputer based on the 740 family core technology. The 3804 group (Spec. H) is designed for household products, office automation equipment, and controlling systems that require analog signal processing, including the A/D converter and D/A converters.
FEATURES
q Basic machine-language instructions ...................................... 71 q Minimum instruction execution time ................................ 0.24 s (at 16.8 MHz oscillation frequency) q Memory size Flash memory .............................................................. 60 K bytes RAM ............................................................................ 2048 bytes q Programmable input/output ports ............................................ 56 q Software pull-up resistors ................................................. Built-in q Interrupts 21 sources, 16 vectors ................................................................. (external 8, internal 12, software 1) q Timers ........................................................................... 16-bit 1 8-bit 4 (with 8-bit prescaler) q Watchdog timer ............................................................ 16-bit 1 q Serial interface Serial I/O1, 3 ............... 8-bit 2 (UART or Clock-synchronized) Serial I/O2 ................................... 8-bit 1 (Clock-synchronized) q PWM ............................................ 8-bit 1 (with 8-bit prescaler) q Multi-master I2C-BUS interface ................................... 1 channel q A/D converter ............................................. 10-bit 16 channels (8-bit reading enabled) q D/A converter .................................................. 8-bit 2 channels q LED direct drive port .................................................................. 8 q Clock generating circuit ..................................... Built-in 2 circuits (connect to external ceramic resonator or quartz-crystal oscillator)
qPower source voltage In high-speed mode At 16.8 MHz oscillation frequency ............................ 4.5 to 5.5 V At 12.5 MHz oscillation frequency ............................ 4.0 to 5.5 V At 8.4 MHz oscillation frequency) ............................. 2.7 to 5.5 V In middle-speed mode At 16.8 MHz oscillation frequency ............................ 4.5 to 5.5 V At 12.5 MHz oscillation frequency ............................ 2.7 to 5.5 V In low-speed mode At 32 kHz oscillation frequency ................................. 2.7 to 5.5 V qPower dissipation In high-speed mode ............................................. 27.5 mW (typ.) (at 16.8 MHz oscillation frequency, at 5 V power source voltage) In low-speed mode ............................................... 1200 W (typ.) (at 32 kHz oscillation frequency, at 3 V power source voltage) qOperating temperature range .................................... -20 to 85C qPackages SP .................................................. 64P4B (64-pin 750 mil SDIP) FP ....................................... 64P6N-A (64-pin 14 14 mm QFP) HP ..................................... 64P6Q-A (64-pin 10 10 mm LQFP) KP ..................................... 64P6U-A (64-pin 14 14 mm LQFP) qPower source voltage ...................................... Vcc = 2.7 to 5.5 V qProgram/Erase voltage .................................... Vcc = 2.7 to 5.5 V qProgramming method ...................... Programming in unit of byte qErasing method ...................................................... Block erasing qProgram/Erase control by software command qNumber of times for programming/erasing ............................ 100 sNotes Cannot be used for application embedded in the MCU card.
Currently support products are listed below. Table 1 Support products Product name M38049FFHSP M38049FFHFP M38049FFHHP M38049FFHKP Flash memory size (bytes) RAM size (bytes) Package 64P4B 64P6N-A 64P6Q-A 64P6U-A Remarks
61440
2048
Vcc = 2.7 to 5.5 V
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-2
HARDWARE 3804 Group (Spec.H) PIN CONFIGURATION
PIN CONFIGURATION (TOP VIEW)
P01/AN9 P02/AN10 P07/AN15 P10/INT41 P11/INT01 P03/AN11 P04/AN12 P00/AN8 P05/AN13 P06/AN14 P13 P14 P15 35 P16 34 P12 P17 33
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17
44
40
41
45
48
P37/SRDY3 P36/SCLK3 P35/TXD3 P34/RXD3 P33/SCL P32/SDA P31/DA2 P30/DA1 VCC VREF AVSS P67/AN7 P66/AN6 P65/AN5 P64/AN4 P63/AN3
49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64
47
46
43
42
39
38
37
36
P20(LED0) P21(LED1) P22(LED2) P23(LED3) P24(LED4) P25(LED5) P26(LED6) P27(LED7) VSS XOUT XIN P40/INT40/XCOUT P41/INT00/XCIN RESET CNVSS P42/INT1
M38049FFHFP/HP/KP
13
12
P62/AN2
P60/AN0
P56/PWM
P54/CNTR0
P51/SOUT2
10
11
P55/CNTR1
P53/SRDY2
P52/SCLK2
P45/TXD1
P57/INT3
P61/AN1
P50/SIN2
14
15 P44/RXD1
P47/SRDY1/CNTR2
Package type : 64P6N-A/64P6Q-A/64P6U-A
Fig. 1 3804 group (Spec. H) pin configuration
PIN CONFIGURATION (TOP VIEW)
VCC VREF AVSS P67/AN7 P66/AN6 P65/AN5 P64/AN4 P63/AN3 P62/AN2 P61/AN1 P60/AN0 P57/INT3 P56/PWM P55/CNTR1 P54/CNTR0 P53/SRDY2 P52/SCLK2 P51/SOUT2 P50/SIN2 P47/SRDY1/CNTR2 P46/SCLK1 P45/TXD1 P44/RXD1 P43/INT2 P42/INT1 CNVSS RESET P41/INT00/XCIN P40/INT40/XCOUT XIN XOUT VSS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 P30/DA1 P31/DA2 P32/SDA P33/SCL P34/RXD3 P35/TXD3 P36/SCLK3 P37/SRDY3 P00/AN8 P01/AN9 P02/AN10 P03/AN11 P04/AN12 P05/AN13 P06/AN14 P07/AN15 P10/INT41 P11/INT01 P12 P13 P14 P15 P16 P17 P20(LED0) P21(LED1) P22(LED2) P23(LED3) P24(LED4) P25(LED5) P26(LED6) P27(LED7)
Package type : 64P4B
Fig. 2 3804 group (Spec. H) pin configuration
P46/SCLK1
P43/INT2
16
5
4
1
3
2
6
7
8
9
M38049FFHSP
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-3
FUNCTIONAL BLOCK DIAGRAM (Package: 64P4B)
Clock Clock Sub-clock Sub-clock input output input output Reset input
X IN X OUT X CIN X COUT V SS V CC RESET CNVSS
26 27 1 32
3804 Group (Spec.H)
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
Data bus CPU Timer 1 (8) A X Y
Prescaler X (8) Prescaler 12 (8)
FUNCTIONAL BLOCK
Fig. 3 Functional block diagram
30
31
28
29
Clock generating circuit
RAM ROM
Timer 2 (8) Timer X (8)
S
CNTR0
PC H PS
PCL
CNTR1
Prescaler Y (8)
Timer Y (8)
Timer Z (16)
CNTR2
A/D converter (10)
PWM(8) SI/O2(8) SI/O1(8)
D/A D/A converter converter 2 (8) 1 (8)
SI/O3(8)
IC
2
INT3
INT00 INT1 INT2 INT40
INT01 INT41
P6(8) P5(8)
P4(8)
P3(8)
P2(8)
P1(8)
P0(8)
2
3
4 5 6 7 8 9 10 11
12 13 14 15 16 17 18 19
20 21 22 23 24 25 28 29
57 58 59 60 61 62 63 64
33 34 35 36 37 38 39 40
41 42 43 44 45 46 47 48
49 50 51 52 53 54 55 56
VREF AVSS
FUNCTIONAL BLOCK
HARDWARE
I/O port P6
I/O port P5
I/O port P4
I/O port P3
I/O port P2 (LED drive)
I/O port P1
I/O port P0
1-4
HARDWARE 3804 Group (Spec.H) PIN DESCRIPTION
PIN DESCRIPTION
Table 2 Pin description Pin VCC, VSS CNVSS VREF AVSS RESET XIN XOUT Name Power source CNVSS input Reference voltage Analog power source Reset input Clock input Clock output Functions *Apply voltage of 2.7 V-5.5 V to Vcc, and 0 V to Vss. *This pin controls the operation mode of the chip. *Normally connected to VSS. *Reference voltage input pin for A/D and D/A converters. *Analog power source input pin for A/D and D/A converters. *Connect to VSS. *Reset input pin for active "L". *Input and output pins for the clock generating circuit. *Connect a ceramic resonator or quartz-crystal oscillator between the XIN and XOUT pins to set the oscillation frequency. *When an external clock is used, connect the clock source to the XIN pin and leave the XOUT pin open. P00/AN8- P07/AN15 P10/INT41 P11/INT01 P12-P17 P20-P27 P30/DA1 P31/DA2 P32/SDA P33/SCL P34/RxD3 P35/TxD3 P36/SCLK3 P37/SRDY3 I/O port P0 I/O port P1 *8-bit CMOS I/O port. *A/D converter input pin *I/O direction register allows each pin to be individually programmed as either input or output. *Interrupt input pin *CMOS compatible input level. *CMOS 3-state output structure. *Pull-up control is enabled in a bit unit. *P20-P27 are enabled to output large current for LED drive. I/O port P3 *8-bit CMOS I/O port. *D/A converter input pin *I/O direction register allows each pin to be individually programmed as either input or output. *I2C-BUS interface function pins *CMOS compatible input level. *P32 to P33 can be switched between CMOS compat- *Serial I/O3 function pin ible input level or SMBUS input level in the I2C-BUS interface function. *P30, P31, P34-P37 are CMOS 3-state output structure. *P32, P33 are N-channel open-drain output structure. *Pull-up control of P30, P31, P34-P37 is enabled in a bit unit. P40/INT40/ XCOUT P41/INT00/ XCIN P42/INT1 P43/INT2 P44/RxD1 P45/TxD1 P46/SCLK1 P47/SRDY1 /CNTR2 P50/SIN2 P51/SOUT2 P52/SCLK2 P53/SRDY2 P54/CNTR0 P55/CNTR1 P56/PWM P57/INT3 P60/AN0- P67/AN7 I/O port P6 I/O port P4 *8-bit CMOS I/O port. *Interrupt input pin *I/O direction register allows each pin to be individually *Sub-clock generating I/O pin programmed as either input or output. (resonator connected) *CMOS compatible input level. *Interrupt input pin *CMOS 3-state output structure. *Pull-up control is enabled in a bit unit. *Serial I/O1 function pin
Function except a port function
I/O port P2
*Serial I/O1, timer Z function pin I/O port P5 *8-bit CMOS I/O port. *I/O direction register allows each pin to be individually programmed as either input or output. *CMOS compatible input level. *CMOS 3-state output structure. *Pull-up control is enabled in a bit unit. *Timer X function pin *Timer Y function pin *PWM output pin *Interrupt input pin *A/D converter input pin *Serial I/O2 function pin
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-5
HARDWARE 3804 Group (Spec.H) PART NUMBERING
PART NUMBERING
Product name
M3804 9
F
F
H
SP
Package type SP : 64P4B FP : 64P6N-A HP : 64P6Q-A KP : 64P6U-A
: standard H : Minner spec. change product
ROM/PROM size 9 : 36864 bytes 1 : 4096 bytes A: 40960 bytes 2 : 8192 bytes B: 45056 bytes 3 : 12288 bytes C: 49152 bytes 4 : 16384 bytes D: 53248 bytes 5 : 20480 bytes E: 57344 bytes 6 : 24576 bytes F : 61440 bytes 7 : 28672 bytes 8 : 32768 bytes
Memory type F : Flash memory version
RAM size 0 : 192 bytes 1 : 256 bytes 2 : 384 bytes 3 : 512 bytes 4 : 640 bytes
5 : 768 bytes 6 : 896 bytes 7 : 1024 bytes 8 : 1536 bytes 9 : 2048 bytes
Fig. 4 Part numbering
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-6
HARDWARE 3804 Group (Spec.H) GROUP EXPANSION
GROUP EXPANSION
Renesas plans to expand the 3804 group (Spec. H) as follows.
Packages
64P4B ......................................... 64-pin shrink plastic-molded DIP 64P6N-A .................................... 0.8 mm-pitch plastic molded QFP 64P6Q-A .................................. 0.5 mm-pitch plastic molded LQFP 64P6U-A .................................. 0.8 mm-pitch plastic molded LQFP
Memory Size
Flash memory size ......................................................... 60 K bytes RAM size ....................................................................... 2048 bytes
Memory Expansion Plan
ROM size (bytes)
: Under development
: Mass production
As of Dec. 2004
60K
M38049FFH M38049FF
48K 32K 28K 24K 20K 16K 12K 8K
384
512
640
768
896
1024
1152
1280
1408
1536
2048
3072
4032
RAM size (bytes)
Fig. 5 Memory expansion plan
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-7
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
FUNCTIONAL DESCRIPTION CENTRAL PROCESSING UNIT (CPU)
The 3804 group (Spec. H) uses the standard 740 Family instruction set. Refer to the table of 740 Family addressing modes and machine instructions or the 740 Family Software Manual for details on the instruction set. Machine-resident 740 Family instructions are as follows: The FST and SLW instructions cannot be used. The STP, WIT, MUL, and DIV instructions can be used.
[Stack Pointer (S)]
The stack pointer is an 8-bit register used during subroutine calls and interrupts. This register indicates start address of stored area (stack) for storing registers during subroutine calls and interrupts. The low-order 8 bits of the stack address are determined by the contents of the stack pointer. The high-order 8 bits of the stack address are determined by the stack page selection bit. If the stack page selection bit is "0" , the high-order 8 bits becomes "0016". If the stack page selection bit is "1", the high-order 8 bits becomes "0116". The operations of pushing register contents onto the stack and popping them from the stack are shown in Figure 7. Store registers other than those described in Figure 6 with program when the user needs them during interrupts or subroutine calls (see Table 3).
[Accumulator (A)]
The accumulator is an 8-bit register. Data operations such as data transfer, etc. are executed mainly through the accumulator.
[Index Register X (X)]
The index register X is an 8-bit register. In the index addressing modes, the value of the OPERAND is added to the contents of register X and specifies the real address.
[Program Counter (PC)]
The program counter is a 16-bit counter consisting of two 8-bit registers PCH and PCL. It is used to indicate the address of the next instruction to be executed.
[Index Register Y (Y)]
The index register Y is an 8-bit register. In partial instruction, the value of the OPERAND is added to the contents of register Y and specifies the real address.
b7 A b7 X b7 Y b7 S b15 PCH b7 b7 PCL
b0 Accumulator b0 Index register X b0 Index register Y b0 Stack pointer b0 Program counter b0 Processor status register (PS) Carry flag Zero flag Interrupt disable flag Decimal mode flag Break flag Index X mode flag Overflow flag Negative flag
NVTBD I ZC
Fig. 6 740 Family CPU register structure
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-8
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
On-going Routine
Interrupt request (Note) Execute JSR M (S) Push return address on stack (S) M (S) (S) (PCH) (S) - 1 (PCL) (S)- 1
M (S) (S) M (S) (S) M (S) (S)
(PCH) (S) - 1 (PCL) (S) - 1 (PS) (S) - 1 Push contents of processor status register on stack Push return address on stack
Subroutine Execute RTS POP return address from stack (S) (PCL) (S) (PCH) (S) + 1 M (S) (S) + 1 M (S)
Interrupt Service Routine
Execute RTI (S) (PS) (S) (PCL) (S) (PCH) (S) + 1 M (S) (S) + 1 M (S) (S) + 1 M (S)
I Flag is set from "0" to "1" Fetch the jump vector POP contents of processor status register from stack
POP return address from stack
Note: Condition for acceptance of an interrupt
Interrupt enable flag is "1" Interrupt disable flag is "0"
Fig. 7 Register push and pop at interrupt generation and subroutine call Table 3 Push and pop instructions of accumulator or processor status register Push instruction to stack Accumulator Processor status register PHA PHP Pop instruction from stack PLA PLP
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-9
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
*Bit 4: Break flag (B) The B flag is used to indicate that the current interrupt was generated by the BRK instruction. The BRK flag in the processor status register is always "0". When the BRK instruction is used to generate an interrupt, the processor status register is pushed onto the stack with the break flag set to "1". *Bit 5: Index X mode flag (T) When the T flag is "0", arithmetic operations are performed between accumulator and memory. When the T flag is "1", direct arithmetic operations and direct data transfers are enabled between memory locations. *Bit 6: Overflow flag (V) The V flag is used during the addition or subtraction of one byte of signed data. It is set if the result exceeds +127 to -128. When the BIT instruction is executed, bit 6 of the memory location operated on by the BIT instruction is stored in the overflow flag. *Bit 7: Negative flag (N) The N flag is set if the result of an arithmetic operation or data transfer is negative. When the BIT instruction is executed, bit 7 of the memory location operated on by the BIT instruction is stored in the negative flag.
[Processor status register (PS)]
The processor status register is an 8-bit register consisting of 5 flags which indicate the status of the processor after an arithmetic operation and 3 flags which decide MCU operation. Branch operations can be performed by testing the Carry (C) flag , Zero (Z) flag, Overflow (V) flag, or the Negative (N) flag. In decimal mode, the Z, V, N flags are not valid. *Bit 0: Carry flag (C) The C flag contains a carry or borrow generated by the arithmetic logic unit (ALU) immediately after an arithmetic operation. It can also be changed by a shift or rotate instruction. *Bit 1: Zero flag (Z) The Z flag is set if the result of an immediate arithmetic operation or a data transfer is "0", and cleared if the result is anything other than "0". *Bit 2: Interrupt disable flag (I) The I flag disables all interrupts except for the interrupt generated by the BRK instruction. Interrupts are disabled when the I flag is "1". *Bit 3: Decimal mode flag (D) The D flag determines whether additions and subtractions are executed in binary or decimal. Binary arithmetic is executed when this flag is "0"; decimal arithmetic is executed when it is "1". Decimal correction is automatic in decimal mode. Only the ADC and SBC instructions can execute decimal arithmetic.
Table 4 Set and clear instructions of each bit of processor status register C flag Set instruction Clear instruction SEC CLC Z flag - - I flag SEI CLI D flag SED CLD B flag - - T flag SET CLT V flag - CLV N flag - -
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-10
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
[CPU Mode Register (CPUM)] 003B16
The CPU mode register contains the stack page selection bit, etc. The CPU mode register is allocated at address 003B16.
b7 1
b0
CPU mode register
(CPUM : address 003B16)
Processor mode bits b1 b0 0 0 : Single-chip mode 0 1: 1 0 : Not available 1 1: Stack page selection bit 0 : 0 page 1 : 1 page Fix this bit to "1". Port XC switch bit 0 : I/O port function (stop oscillating) 1 : XCIN-XCOUT oscillating function Main clock (XIN-XOUT) stop bit 0 : Oscillating 1 : Stopped Main clock division ratio selection bits b7 b6 0 0 : = f(XIN)/2 (high-speed mode) 0 1 : = f(XIN)/8 (middle-speed mode) 1 0 : = f(XCIN)/2 (low-speed mode) 1 1 : Not available
Fig. 8 Structure of CPU mode register
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-11
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
qMiddle-speed mode automatic switch by SCL/SDA Interrupt The SCL/SDA interrupt source enables an automatic switch when the middle-speed mode automatic switch set bit (bit 1) of MISRG (address 001016) is set to "1". The conditions for an automatic switch execution depend on the settings of bits 5 and 6 of the I2C START/STOP condition control register (address 001616). Bit 5 is the SCL/SDA interrupt pin polarity selection bit and bit 6 is the SCL/SDA interrupt pin selection bit. The main clock oscillation stabilizing time can also be selected by middle-speed mode automatic switch wait time set bit (bit 2) of the MISRG. qMiddle-speed mode automatic switch by program The middle-speed mode can also be automatically switched by program while operating in low-speed mode. By setting the middle-speed automatic switch start bit (bit 3) of MISRG (address 001016) to "1" in the condition that the middle-speed mode automatic switch set bit is "1" while operating in low-speed mode, the MCU will automatically switch to middle-speed mode. In this case, the oscillation stabilizing time of the main clock can be selected by the middle-speed automatic switch wait time set bit (bit 2) of MISRG (address 001016).
MISRG
(1) Bit 0 of address 001016: Oscillation stabilizing time set after STP instruction released bit When the MCU stops the clock oscillation by the STP instruction and the STP instruction has been released by an external interrupt source, usually, the fixed values of Timer 1 and Prescaler 12 (Timer 1 = 0116, Prescaler 12 = FF16) are automatically reloaded in order for the oscillation to stabilize. The user can inhibit the automatic setting by setting "1" to bit 0 of MISRG (address 001016). However, by setting this bit to "1", the previous values, set just before the STP instruction was executed, will remain in Timer 1 and Prescaler 12. Therefore, you will need to set an appropriate value to each register, in accordance with the oscillation stabilizing time, before executing the STP instruction. Figure 9 shows the structure of MISRG. (2) Bits 1, 2, 3 of address 001016: Middle-speed Mode Automatic Switch Function In order to switch the clock mode of an MCU which has a subclock, the following procedure is necessary: set CPU mode register (003B16) --> start main clock oscillation --> wait for oscillation stabilization --> switch to middle-speed mode (or high-speed mode). However, the 3804 group (Spec. H) has the built-in function which automatically switches from low to middle-speed mode either by the SCL/SDA interrupt or by program.
b7
b0
MISRG (MISRG : address 001016) Oscillation stabilizing time set after STP instruction released bit 0: Automatically set "0116" to Timer 1, "FF16" to Prescaler 12 1: Automatically set disabled Middle-speed mode automatic switch set bit 0: Not set automatically 1: Automatic switching enabled (Note1, 2) Middle-speed mode automatic switch wait time set bit 0: 4.5 to 5.5 machine cycles 1: 6.5 to 7.5 machine cycles Middle-speed mode automatic switch start bit (Depending on program) 0: Invalid 1: Automatic switch start (Note1) Not used (return "0" when read) (Do not write "1" to this bit) Note 1: During operation in low-speed mode, it is possible automatically to switch to middle-speed mode owing to SCL/SDA interrupt. 2: When automatic switch to middle-speed mode from low-speed mode occurs, the values of CPU mode register (003B16) change.
Fig. 9 Structure of MISRG
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-12
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
MEMORY Special Function Register (SFR) Area
The Special Function Register area in the zero page contains control registers such as I/O ports and timers.
Interrupt Vector Area
The interrupt vector area contains reset and interrupt vectors.
Zero Page
Access to this area with only 2 bytes is possible in the zero page addressing mode.
RAM
The RAM is used for data storage and for stack area of subroutine calls and interrupts.
Special Page
Access to this area with only 2 bytes is possible in the special page addressing mode.
ROM
The ROM area can program/erase.
RAM area
RAM size (bytes) Address XXXX16
000016 SFR area 004016 010016 RAM Zero page
192 256 384 512 640 768 896 1024 1536 2048
00FF16 013F16 01BF16 023F16 02BF16 033F16 03BF16 043F16 063F16 083F16
XXXX16 Not used 0FF016 0FFF16 SFR area Not used
ROM area
ROM size (bytes) Address YYYY16
YYYY16
4096 8192 12288 16384 20480 24576 28672 32768 36864 40960 45056 49152 53248 57344 61440
F00016 E00016 D00016 C00016 B00016 A00016 900016 800016 700016 600016 500016 400016 300016 200016 100016
ROM FF0016 FFDC16 Interrupt vector area FFFE16 FFFF16 Special page
Fig. 10 Memory map diagram
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-13
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
000016 000116 000216 000316 000416 000516 000616 000716 000816 000916 000A16 000B16 000C16 000D16 000E16 000F16 001016 001116 001216 001316 001416 001516 001616 001716 001816 001916 001A16 001B16 001C16 001D16 001E16 001F16
Port P0 (P0) Port P0 direction register (P0D) Port P1 (P1) Port P1 direction register (P1D) Port P2 (P2) Port P2 direction register (P2D) Port P3 (P3) Port P3 direction register (P3D) Port P4 (P4) Port P4 direction register (P4D) Port P5 (P5) Port P5 direction register (P5D) Port P6 (P6) Port P6 direction register (P6D) Timer 12, X count source selection register (T12XCSS) Timer Y, Z count source selection register (TYZCSS) MISRG I2C data shift register (S0) I2C special mode status register (S3) I2C status register (S1) I2C control register (S1D) I2C clock control register (S2) I2C START/STOP condition control register (S2D) I2C special mode control register (S3D) Transmit/Receive buffer register 1 (TB1/RB1) Serial I/O1 status register (SIO1STS) Serial I/O1 control register (SIO1CON) UART1 control register (UART1CON) Baud rate generator 1 (BRG1) Serial I/O2 control register (SIO2CON) Watchdog timer control register (WDTCON) Serial I/O2 register (SIO2)
002016 002116 002216 002316 002416 002516 002616 002716 002816 002916 002A16 002B16 002C16 002D16 002E16 002F16 003016 003116 003216 003316 003416 003516 003616 003716 003816 003916 003A16 003B16 003C16 003D16 003E16 003F16
Prescaler 12 (PRE12) Timer 1 (T1) Timer 2 (T2) Timer XY mode register (TM) Prescaler X (PREX) Timer X (TX) Prescaler Y (PREY) Timer Y (TY) Timer Z low-order (TZL) Timer Z high-order (TZH) Timer Z mode register (TZM) PWM control register (PWMCON) PWM prescaler (PREPWM) PWM register (PWM)
Baud rate generator 3 (BRG3) Transmit/Receive buffer register 3 (TB3/RB3) Serial I/O3 status register (SIO3STS) Serial I/O3 control register (SIO3CON) UART3 control register (UART3CON) AD/DA control register (ADCON) AD conversion register 1 (AD1) DA1 conversion register (DA1) DA2 conversion register (DA2) AD conversion register 2 (AD2) Interrupt source selection register (INTSEL) Interrupt edge selection register (INTEDGE) CPU mode register (CPUM) Interrupt request register 1 (IREQ1) Interrupt request register 2 (IREQ2) Interrupt control register 1 (ICON1) Interrupt control register 2 (ICON2)
0FE016 0FE116 0FE216 0FE316 0FE416 0FE516 0FE616 0FE716 0FE816 0FE916 0FEA16 0FEB16 0FEC16 0FED16 0FEE16 0FEF16
Flash memory control register 0 (FMCR0) Flash memory control register 1 (FMCR1) Flash memory control register 2 (FMCR2) Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved
0FF016 0FF116 0FF216 0FF316 0FF416 0FF516 0FF616 0FF716 0FF816 0FF916
Port P0 pull-up control register (PULL0) Port P1 pull-up control register (PULL1) Port P2 pull-up control register (PULL2) Port P3 pull-up control register (PULL3) Port P4 pull-up control register (PULL4) Port P5 pull-up control register (PULL5) Port P6 pull-up control register (PULL6) I2C slave address register 0 (S0D0) I2C slave address register 1 (S0D1) I2C slave address register 2 (S0D2)
Reserved area: Do not write any data to these addresses, because these areas are reserved.
Fig. 11 Memory map of special function register (SFR)
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-14
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
comes an input pin. When "1" is written to that bit, that pin becomes an output pin. If data is read from a pin which is set to output, the value of the port output latch is read, not the value of the pin itself. Pins set to input are floating. If a pin set to input is written to, only the port output latch is written to and the pin remains floating.
I/O PORTS
The I/O ports have direction registers which determine the input/ output direction of each individual pin. Each bit in a direction register corresponds to one pin, and each pin can be set to be input port or output port. When "0" is written to the bit corresponding to a pin, that pin beTable 5 I/O port function Pin P00/AN8-P07/AN15 P10/INT41 P11/INT01 P12-P17 P20/LED0- P27/LED7 P30/DA1 P31/DA2 P32/SDA P33/SCL Name Port P0 Port P1 I/O Structure CMOS compatible input level CMOS 3-state output
Non-Port Function A/D converter input External interrupt input
Related SFRs AD/DA control register Interrupt edge selection register
Ref.No. (1) (2) (3)
Port P2 Port P3 CMOS compatible input level CMOS 3-state output CMOS compatible input level N-channel open-drain output CMOS/SMBUS input level (when selecting I2C-BUS interface function) CMOS compatible input level CMOS 3-state output D/A converter output I2C-BUS interface function I/O AD/DA control register I2C control register (4) (5)
P34/RxD3 P35/TxD3 P36/SCLK3 P37/SRDY3 P40/INT40/XCIN P41/INT00/XCOUT P42/INT1 P43/INT2 P44/RxD1 P45/TxD1 P46/SCLK1 P47/SRDY1/CNTR2
Serial I/O3 function I/O
Serial I/O3 control register UART3 control register Interrupt edge selection register CPU mode register Interrupt edge selection register Serial I/O1 control register UART1 control register Serial I/O1 control register Timer Z mode register Serial I/O2 control register
(6) (7) (8) (9) (10) (11) (2) (6) (7) (8) (12)
Port P4
CMOS compatible input level CMOS 3-state output
External interrupt input Sub-clock generating circuit External interrupt input Serial I/O1 function I/O
Serial I/O1 function I/O Timer Z function I/O Port P5 CMOS compatible input level CMOS 3-state output Serial I/O2 function I/O
P50/SIN2 P51/SOUT2 P52/SCLK2 P53/SRDY2 P54/CNTR0 P55/CNTR1 P56/PWM P57/INT3 P60/AN0-P67/AN7
Timer X, Y function I/O PWM output External interrupt input Port P6 CMOS compatible input level CMOS 3-state output A/D converter input
Timer XY mode register PWM control register Interrupt edge selection register AD/DA control register
(13) (14) (15) (16) (17) (18) (2) (1)
Notes 1: Refer to the applicable sections how to use double-function ports as function I/O ports. 2: Make sure that the input level at each pin is either 0 V or VCC during execution of the STP instruction. When an input level is at an intermediate potential, a current will flow from VCC to VSS through the input-stage gate.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-15
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
(1) Ports P0, P6
Pull-up control bit
(2) Ports P10, P11, P42, P43, P57
Pull-up control bit Direction register Direction register
Data bus
Port latch Data bus Port latch
A/D converter input Analog input pin selection bit Interrupt input
(3) Ports P12 to P17, P2
Pull-up control bit Direction register
(4) Ports P30, P31
Pull-up control bit Direction register
Data bus
Port latch
Data bus
Port latch
D/A converter output DA1 output enable (P30) DA2 output enable (P31)
(5) Ports P32, P33
I2C-BUS interface enable bit Direction register
(6) Ports P34, P44
Pull-up control bit Serial I/O enable bit Receive enable bit Direction register Port latch Data bus Port latch
Data bus
SDA output SCL output
SDA input SCL input Serial I/O input
(7) Ports P35, P45
Pull-up control bit Serial I/O enable bit Transmit enable bit Direction register P-channel output disable bit
(8) Ports P36, P46
Serial I/O synchronous clock selection bit
Pull-up control bit
Serial I/O enable bit Serial I/O mode selection bit Serial I/O enable bit Direction register
Data bus
Port latch
Data bus
Port latch
Serial I/O output
Serial I/O clock output Serial I/O external clock input
Fig. 12 Port block diagram (1)
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-16
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
(9) Port P37
Pull-up control bit Serial I/O3 mode selection bit Serial I/O3 enable bit SRDY3 output enable bit Direction register
(10) Port P40
Pull-up control bit
Port XC switch bit Direction register
Data bus
Port latch
Data bus
Port latch
INT40 interrupt input Serial I/O3 ready output Port P41 Port XC switch bit Oscillator
(11) Port P41
Pull-up control bit
(12) Port P47
Timer Z operating mode bits Bit 2 Bit 1 Bit 0 Serial I/O1 mode selection bit Serial I/O1 enable bit SRDY1 output enable bit Direction register Pull-up control bit
Port XC switch bit Direction register
Data bus
Port latch
Data bus
Port latch
INT00 interrupt input Sub-clock generating circuit input Timer output Serial I/O1 ready output CNTR2 interrupt input
(13) Port P50
Pull-up control bit
(14) Port P51
Pull-up control bit
Serial I/O2 transmit completion signal Serial I/O2 port selection bit Direction register Direction register Data bus Port latch
P-channel output disable bit
Data bus
Port latch
Serial I/O2 input Serial I/O2 output
Fig. 13 Port block diagram (2)
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-17
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
(15) Port P52
Pull-up control bit
Serial I/O2 synchronous clock selection bit
(16) Port P53
Pull-up control bit
Serial I/O2 port selection bit
SRDY2 enable bit Direction register
Direction register Data bus Data bus Port latch
Port latch
Serial I/O2 ready output Serial I/O2 clock output Serial I/O2 external clock input
(17) Ports P54, P55
(18) Port P56
Pull-up control bit
Pull-up control bit
PWM output enable bit Direction register Direction register
Data bus
Port latch
Data bus
Port latch
Pulse output mode Timer output
PWM output
CNTR interrupt input
Fig. 14 Port block diagram (3)
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-18
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
b7
b0 Port P0 pull-up control register (PULL0: address 0FF016) P00 pull-up control bit 0: No pull-up 1: Pull-up P01 pull-up control bit 0: No pull-up 1: Pull-up P02 pull-up control bit 0: No pull-up 1: Pull-up P03 pull-up control bit 0: No pull-up 1: Pull-up P04 pull-up control bit 0: No pull-up 1: Pull-up P05 pull-up control bit 0: No pull-up 1: Pull-up P06 pull-up control bit 0: No pull-up 1: Pull-up P07 pull-up control bit 0: No pull-up 1: Pull-up
Note: Pull-up control is valid when the corresponding bit of the port direction register is "0" (input). When that bit is "1" (output), pull-up cannot be set to the port of which pull-up is selected.
b7
b0 Port P1 pull-up control register (PULL1: address 0FF116) P10 pull-up control bit 0: No pull-up 1: Pull-up P11 pull-up control bit 0: No pull-up 1: Pull-up P12 pull-up control bit 0: No pull-up 1: Pull-up P13 pull-up control bit 0: No pull-up 1: Pull-up P14 pull-up control bit 0: No pull-up 1: Pull-up P15 pull-up control bit 0: No pull-up 1: Pull-up P16 pull-up control bit 0: No pull-up 1: Pull-up P17 pull-up control bit 0: No pull-up 1: Pull-up
Note: Pull-up control is valid when the corresponding bit of the port direction register is "0" (input). When that bit is "1" (output), pull-up cannot be set to the port of which pull-up is selected.
Fig. 15 Structure of port pull-up control register (1)
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-19
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
b7
b0 Port P2 pull-up control register (PULL2: address 0FF216) P20 pull-up control bit 0: No pull-up 1: Pull-up P21 pull-up control bit 0: No pull-up 1: Pull-up P22 pull-up control bit 0: No pull-up 1: Pull-up P23 pull-up control bit 0: No pull-up 1: Pull-up P24 pull-up control bit 0: No pull-up 1: Pull-up P25 pull-up control bit 0: No pull-up 1: Pull-up P26 pull-up control bit 0: No pull-up 1: Pull-up P27 pull-up control bit 0: No pull-up 1: Pull-up
Note: Pull-up control is valid when the corresponding bit of the port direction register is "0" (input). When that bit is "1" (output), pull-up cannot be set to the port of which pull-up is selected.
b7
b0 Port P3 pull-up control register (PULL3: address 0FF316) P30 pull-up control bit 0: No pull-up 1: Pull-up P31 pull-up control bit 0: No pull-up 1: Pull-up Not used (return "0" when read) P34 pull-up control bit 0: No pull-up 1: Pull-up P35 pull-up control bit 0: No pull-up 1: Pull-up P36 pull-up control bit 0: No pull-up 1: Pull-up P37 pull-up control bit 0: No pull-up 1: Pull-up
Note: Pull-up control is valid when the corresponding bit of the port direction register is "0" (input). When that bit is "1" (output), pull-up cannot be set to the port of which pull-up is selected.
Fig. 16 Structure of port pull-up control register (2)
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-20
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
b7
b0 Port P4 pull-up control register (PULL4: address 0FF416) P40 pull-up control bit 0: No pull-up 1: Pull-up P41 pull-up control bit 0: No pull-up 1: Pull-up P42 pull-up control bit 0: No pull-up 1: Pull-up P43 pull-up control bit 0: No pull-up 1: Pull-up P44 pull-up control bit 0: No pull-up 1: Pull-up P45 pull-up control bit 0: No pull-up 1: Pull-up P46 pull-up control bit 0: No pull-up 1: Pull-up P47 pull-up control bit 0: No pull-up 1: Pull-up
Note: Pull-up control is valid when the corresponding bit of the port direction register is "0" (input). When that bit is "1" (output), pull-up cannot be set to the port of which pull-up is selected.
b7
b0 Port P5 pull-up control register (PULL5: address 0FF516) P50 pull-up control bit 0: No pull-up 1: Pull-up P51 pull-up control bit 0: No pull-up 1: Pull-up P52 pull-up control bit 0: No pull-up 1: Pull-up P53 pull-up control bit 0: No pull-up 1: Pull-up P54 pull-up control bit 0: No pull-up 1: Pull-up P55 pull-up control bit 0: No pull-up 1: Pull-up P56 pull-up control bit 0: No pull-up 1: Pull-up P57 pull-up control bit 0: No pull-up 1: Pull-up
Note: Pull-up control is valid when the corresponding bit of the port direction register is "0" (input). When that bit is "1" (output), pull-up cannot be set to the port of which pull-up is selected.
Fig. 17 Structure of port pull-up control register (3)
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-21
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
b7
b0 Port P6 pull-up control register (PULL6: address 0FF616) P60 pull-up control bit 0: No pull-up 1: Pull-up P61 pull-up control bit 0: No pull-up 1: Pull-up P62 pull-up control bit 0: No pull-up 1: Pull-up P63 pull-up control bit 0: No pull-up 1: Pull-up P64 pull-up control bit 0: No pull-up 1: Pull-up P65 pull-up control bit 0: No pull-up 1: Pull-up P66 pull-up control bit 0: No pull-up 1: Pull-up P67 pull-up control bit 0: No pull-up 1: Pull-up
Note: Pull-up control is valid when the corresponding bit of the port direction register is "0" (input). When that bit is "1" (output), pull-up cannot be set to the port of which pull-up is selected.
Fig. 18 Structure of port pull-up control register (4)
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-22
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
INTERRUPTS
The 3804 group (Spaec. H)'s interrupts are a type of vector and occur by 16 sources among 23 sources: nine external, thirteen internal, and one software.
s Notes
When setting the followings, the interrupt request bit may be set to "1". *When setting external interrupt active edge Related register: Interrupt edge selection register (address 003A16) Timer XY mode register (address 002316) Timer Z mode register (address 002A16) I2C START/STOP condition control register (address 001616) *When switching interrupt sources of an interrupt vector address where two or more interrupt sources are allocated Related register: Interrupt source selection register (address 003916) When not requiring for the interrupt occurrence synchronized with these setting, take the following sequence. Set the corresponding interrupt enable bit to "0" (disabled). Set the interrupt edge select bit or the interrupt source select bit to "1". Set the corresponding interrupt request bit to "0" after 1 or more instructions have been executed. {Set the corresponding interrupt enable bit to "1" (enabled).
Interrupt Control
Each interrupt is controlled by an interrupt request bit, an interrupt enable bit, and the interrupt disable flag except for the software interrupt set by the BRK instruction. An interrupt occurs if the corresponding interrupt request and enable bits are "1" and the interrupt disable flag is "0". Interrupt enable bits can be set or cleared by software. Interrupt request bits can be cleared by software, but cannot be set by software. The reset and the BRK instruction cannot be disabled with any flag or bit. The I (interrupt disable) flag disables all interrupts except the reset and the BRK instruction interrupt. When several interrupt requests occur at the same time, the interrupts are received according to priority.
Interrupt Operation
By acceptance of an interrupt, the following operations are automatically performed: 1. The contents of the program counter and the processor status register are automatically pushed onto the stack. 2. The interrupt disable flag is set and the corresponding interrupt request bit is cleared. 3. The interrupt jump destination address is read from the vector table into the program counter.
Interrupt Source Selection
Which of each combination of the following interrupt sources can be selected by the interrupt source selection register (address 003916). 1. INT0 or Timer Z 2. Serial I/O1 transmission or SCL, SDA 3. CNTR0 or SCL, SDA 4. CNTR1 or Serial I/O3 reception 5. Serial I/O2 or Timer Z 6. INT2 or I2C 7. INT4 or CNTR2 8. A/D converter or serial I/O3 transmission
External Interrupt Pin Selection
The occurrence sources of the external interrupt INT0 and INT4 can be selected from either input from INT00 and INT40 pin, or input from INT01 and INT41 pin by the INT0, INT4 interrupt switch bit of interrupt edge selection register (bit 6 of address 003A16).
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-23
HARDWARE 3804 Group (Spec.H)
Table 6 Interrupt vector addresses and priority Interrupt Source Reset (Note 2) INT0 Timer Z INT1 Serial I/O1 reception Serial I/O1 transmission SCL, SDA Timer X Timer Y Timer 1 Timer 2 CNTR0 SCL, SDA CNTR1 Serial I/O3 reception Serial I/O2 Timer Z INT2 I 2C INT3 INT4 CNTR2 A/D converter Serial I/O3 transmission BRK instruction 16 FFDF16 FFDE16 11 FFE916 FFE816 6 7 8 9 10 FFF316 FFF116 FFEF16 FFED16 FFEB16 FFF216 FFF016 FFEE16 FFEC16 FFEA16 Priority 1 2 Vector Addresses (Note 1) High Low FFFD16 FFFC16 FFFB16 FFFA16 Interrupt Request Generating Conditions At reset At detection of either rising or falling edge of INT0 input At timer Z underflow At detection of either rising or falling edge of INT1 input At completion of serial I/O1 data reception At completion of serial I/O1 transmission shift or when transmission buffer is empty At detection of either rising or falling edge of SCL or SDA At timer X underflow At timer Y underflow At timer 1 underflow At timer 2 underflow At detection of either rising or falling edge of CNTR0 input At detection of either rising or falling edge of SCL or SDA At detection of either rising or falling edge of CNTR1 input At completion of serial I/O3 data reception At completion of serial I/O2 data transmission or reception At timer Z underflow 13 FFE516 FFE416 At detection of either rising or falling edge of INT2 input At completion of data transfer At detection of either rising or falling edge of INT3 input At detection of either rising or falling edge of INT4 input At detection of either rising or falling edge of CNTR2 input At completion of A/D conversion At completion of serial I/O3 transmission shift or when transmission buffer is empty 17 FFDD16 FFDC16 At BRK instruction execution Valid when serial I/O3 is selected External interrupt (active edge selectable) External interrupt (active edge selectable) External interrupt (active edge selectable) External interrupt (active edge selectable) External interrupt (active edge selectable) External interrupt (active edge selectable) External interrupt (active edge selectable) Valid when serial I/O3 is selected Valid when serial I/O2 is selected STP release timer underflow Remarks Non-maskable External interrupt (active edge selectable) External interrupt (active edge selectable) Valid when serial I/O1 is selected Valid when serial I/O1 is selected
FUNCTIONAL DESCRIPTION
3 4 5
FFF916 FFF716 FFF516
FFF816 FFF616 FFF416
External interrupt (active edge selectable)
12
FFE716
FFE616
14 15
FFE316 FFE116
FFE216 FFE016
Non-maskable software interrupt
Notes 1: Vector addresses contain interrupt jump destination addresses. 2: Reset function in the same way as an interrupt with the highest priority.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-24
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
Interrupt request bit Interrupt enable bit
Interrupt disable flag (I)
BRK instruction Reset
Interrupt request
Fig. 19 Interrupt control
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-25
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
b7
b0
Interrupt edge selection register (INTEDGE : address 003A16) INT0 active edge selection bit INT1 active edge selection bit Not used (returns "0" when read) INT2 active edge selection bit INT3 active edge selection bit INT4 active edge selection bit INT0, INT4 interrupt switch bit 0 : INT00, INT40 interrupt 1 : INT01, INT41 interrupt Not used (returns "0" when read) 0 : Falling edge active 1 : Rising edge active 0 : Falling edge active 1 : Rising edge active
b7
b0
Interrupt request register 1 (IREQ1 : address 003C16) INT0/Timer Z interrupt request bit INT1 interrupt request bit Serial I/O1 receive interrupt request bit Serial I/O1 transmit/SCL, SDA interrupt request bit Timer X interrupt request bit Timer Y interrupt request bit Timer 1 interrupt request bit Timer 2 interrupt request bit
b7
b0
Interrupt request register 2 (IREQ2 : address 003D16)
CNTR0/SCL, SDA interrupt request bit CNTR1/Serial I/O3 receive interrupt request bit Serial I/O2/Timer Z interrupt request bit INT2/I2C interrupt request bit INT3 interrupt request bit INT4/CNTR2 interrupt request bit AD converter/Serial I/O3 transmit interrupt request bit Not used (returns "0" when read) 0 : No interrupt request issued 1 : Interrupt request issued b7 b0 Interrupt control register 2 (ICON2 : address 003F16) CNTR0/SCL, SDA interrupt enable bit CNTR1/Serial I/O3 receive interrupt enable bit Serial I/O2/Timer Z interrupt enable bit INT2/I2C interrupt enable bit INT3 interrupt enable bit INT4/CNTR2 interrupt enable bit AD converter/Serial I/O3 transmit interrupt enable bit Not used (returns "0" when read) 0 : Interrupts disabled 1 : Interrupts enabled
b7
b0
Interrupt control register 1 (ICON1 : address 003E16) INT0/Timer Z interrupt enable bit INT1 interrupt enable bit Serial I/O1 receive interrupt enable bit Serial I/O1 transmit/SCL, SDA interrupt enable bit Timer X interrupt enable bit Timer Y interrupt enable bit Timer 1 interrupt enable bit Timer 2 interrupt enable bit
b7
b0
Interrupt source selection register (INTSEL: address 003916) INT0/Timer Z interrupt source selection bit 0 : INT0 interrupt 1 : Timer Z interrupt (Do not write "1" to these bits simultaneously.) Serial I/O2/Timer Z interrupt source selection bit 0 : Serial I/O2 interrupt 1 : Timer Z interrupt Serial I/O1 transmit/SCL, SDA interrupt source selection bit 0 : Serial I/O1 transmit interrupt 1 : SCL, SDA interrupt (Do not write "1" to these bits simultaneously.) CNTR0/SCL, SDA interrupt source selection bit 0 : CNTR0 interrupt 1 : SCL, SDA interrupt INT4/CNTR2 interrupt source selection bit 0 : INT4 interrupt 1 : CNTR2 interrupt INT2/I2C interrupt source selection bit 0 : INT2 interrupt 1 : I2C interrupt CNTR1/Serial I/O3 receive interrupt source selection bit 0 : CNTR1 interrupt 1 : Serial I/O3 receive interrupt AD converter/Serial I/O3 transmit interrupt source selection bit 0 : A/D converter interrupt 1 : Serial I/O3 transmit interrupt
Fig. 20 Structure of interrupt-related registers
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-26
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
TIMERS q8-bit Timers
The 3804 group (Spec. H) has four 8-bit timers: timer 1, timer 2, timer X, and timer Y. The timer 1 and timer 2 use one prescaler in common, and the timer X and timer Y use each prescaler. Those are 8-bit prescalers. Each of the timers and prescalers has a timer latch or a prescaler latch. The division ratio of each timer or prescaler is given by 1/(n + 1), where n is the value in the corresponding timer or prescaler latch. All timers are down-counters. When the timer reaches "0016", an underflow occurs at the next count pulse and the contents of the corresponding timer latch are reloaded into the timer and the count is continued. When the timer underflows, the interrupt request bit corresponding to that timer is set to "1". qTimer divider The divider count source is switched by the main clock division ratio selection bits of CPU mode register (bits 7 and 6 at address 003B16). When these bits are "00" (high-speed mode) or "01" (middle-speed mode), XIN is selected. When these bits are"10" (low-speed mode), XCIN is selected. qPrescaler 12 The prescaler 12 counts the output of the timer divider. The count source is selected by the timer 12, X count source selection register among 1/2, 1/4, 1/8, 1/16, 1/32, 1/64, 1/128, 1/256, 1/512, 1/1024 of f(XIN) or f(XCIN).
Timer X and Timer Y
The timer X and timer Y can each select one of four operating modes by setting the timer XY mode register (address 002316).
(1) Timer mode
qMode selection This mode can be selected by setting "00" to the timer X operating mode bits (bits 1 and 0) and the timer Y operating mode bits (bits 5 and 4) of the timer XY mode register (address 002316). qExplanation of operation The timer count operation is started by setting "0" to the timer X count stop bit (bit 3) and the timer Y count stop bit (bit 7) of the timer XY mode register (address 002316). When the timer reaches "0016", an underflow occurs at the next count pulse and the contents of timer latch are reloaded into the timer and the count is continued.
(2) Pulse output mode
qMode selection This mode can be selected by setting "01" to the timer X operating mode bits (bits 1 and 0) and the timer Y operating mode bits (bits 5 and 4) of the timer XY mode register (address 002316). qExplanation of operation The operation is the same as the timer mode's. Moreover the pulse which is inverted each time the timer underflows is output from CNTR0/CNTR1 pin. Regardless of the timer counting or not the output of CNTR0/CNTR1 pin is initialized to the level of specified by their active edge switch bits when writing to the timer. When the CNTR0 active edge switch bit (bit 2) and the CNTR1 active edge switch bit (bit 6) of the timer XY mode register (address 002316) is "0", the output starts with "H" level. When it is "1", the output starts with "L" level. Switching the CNTR0 or CNTR1 active edge switch bit will reverse the output level of the corresponding CNTR0 or CNTR1 pin. sPrecautions Set the double-function port of CNTR0/CNTR1 pin and port P54/ P55 to output in this mode.
Timer 1 and Timer 2
The timer 1 and timer 2 counts the output of prescaler 12 and periodically set the interrupt request bit. qPrescaler X and prescaler Y The prescaler X and prescaler Y count the output of the timer divider or f(XCIN). The count source is selected by the timer 12, X count source selection register (address 000E16) and the timer Y, Z count source selection register (address 000F16) among 1/2, 1/4, 1/8, 1/16, 1/32, 1/64, 1/128, 1/256, 1/512, and 1/1024 of f(XIN) or f(XCIN); and f(XCIN).
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-27
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
(3) Event counter mode
qMode selection This mode can be selected by setting "10" to the timer X operating mode bits (bits 1 and 0) and the timer Y operating mode bits (bits 5 and 4) of the timer XY mode register (address 002316). qExplanation of operation The operation is the same as the timer mode's except that the timer counts signals input from the CNTR0 or CNTR1 pin. The valid edge for the count operation depends on the CNTR0 active edge switch bit (bit 2) or the CNTR1 active edge switch bit (bit 6) of the timer XY mode register (address 002316). When it is "0", the rising edge is valid. When it is "1", the falling edge is valid. sPrecautions Set the double-function port of CNTR0/CNTR1 pin and port P54/ P55 to input in this mode.
(4) Pulse width measurement mode
qMode selection This mode can be selected by setting "11" to the timer X operating mode bits (bits 1 and 0) and the timer Y operating mode bits (bits 5 and 4) of the timer XY mode register (address 002316). qExplanation of operation When the CNTR0 active edge switch bit (bit 2) or the CNTR1 active edge switch bit (bit 6) of the timer XY mode register (address 002316) is "1", the timer counts during the term of one falling edge of CNTR0/CNTR1 pin input until the next rising edge of input ("L" term). When it is "0", the timer counts during the term of one rising edge input until the next falling edge input ("H" term). sPrecautions Set the double-function port of CNTR0/CNTR1 pin and port P54/ P55 to input in this mode. The count operation can be stopped by setting "1" to the timer X count stop bit (bit 3) and the timer Y count stop bit (bit 7) of the timer XY mode register (address 002316). The interrupt request bit is set to "1" each time the timer underflows. *Precautions when switching count source When switching the count source by the timer 12, X and Y count source selection bits, the value of timer count is altered in inconsiderable amount owing to generating of thin pulses on the count input signals. Therefore, select the timer count source before setting the value to the prescaler and the timer.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-28
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
XIN
"00" "01"
(1/2, 1/4, 1/8, 1/16, 1/32, 1/64, 1/128, 1/256, 1/512, 1/1024) Divider Count source selection bit Data bus
XCIN
Clock for timer 12 Clock for timer Y
Main clock division ratio selection bits
Clock for timer X
"10"
Prescaler X latch (8) f(XCIN) Pulse width measurement mode Timer mode Pulse output mode Prescaler X (8) CNTR0 active edge switch bit "0" "1 " CNTR0 active edge switch bit "1" Q Q Event counter mode Timer X count stop bit
Timer X latch (8)
Timer X (8)
To timer X interrupt request bit
P54/CNTR0
To CNTR0 interrupt request bit
Toggle flip-flop T R Timer X latch write pulse Pulse output mode
Port P54 direction register
Port P54 latch
"0"
Pulse output mode Data bus Count source selection bit
Clock for timer Y f(XCIN) Pulse width measurement mode
Prescaler Y latch (8) Timer mode Pulse output mode Prescaler Y (8)
Timer Y latch (8)
Timer Y (8)
P55/CNTR1
CNTR1 active edge switch bit "0" "1"
To timer Y interrupt request bit
Event counter mode
Timer Y count stop bit To CNTR1 interrupt request bit
CNTR1 active edge switch bit "1"
Q Toggle flip-flop T Q R Timer Y latch write pulse Pulse output mode
Port P55 direction register
Port P55 latch
"0"
Pulse output mode Data bus
Prescaler 12 latch (8)
Timer 1 latch (8)
Timer 2 latch (8)
Clock for timer 12
Prescaler 12 (8)
Timer 1 (8)
Timer 2 (8)
To timer 2 interrupt request bit
To timer 1 interrupt request bit
Fig. 21 Block diagram of timer X, timer Y, timer 1, and timer 2
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-29
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
b7
b0
Timer XY mode register (TM : address 002316) Timer X operating mode bits b1 b0 0 0 : Timer mode 0 1 : Pulse output mode 1 0 : Event counter mode 1 1 : Pulse width measurement mode CNTR0 active edge switch bit 0 : Interrupt at falling edge Count at rising edge in event counter mode 1 : Interrupt at rising edge Count at falling edge in event counter mode Timer X count stop bit 0 : Count start 1 : Count stop Timer Y operating mode bits b5 b4 0 0 : Timer mode 0 1 : Pulse output mode 1 0 : Event counter mode 1 1 : Pulse width measurement mode CNTR1 active edge switch bit 0 : Interrupt at falling edge Count at rising edge in event counter mode 1 : Interrupt at rising edge Count at falling edge in event counter mode Timer Y count stop bit 0 : Count start 1 : Count stop
Fig. 22 Structure of timer XY mode register
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-30
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
b7
b0
Timer 12, X count source selection register (T12XCSS : address 000E16) Timer 12 count source selection bits b3b2b1b0 1010 : 0 0 0 0 : f(XIN)/2 or f(XCIN)/2 1011 : 0 0 0 1 : f(XIN)/4 or f(XCIN)/4 1100 : 0 0 1 0 : f(XIN)/8 or f(XCIN)/8 1101 : 0 0 1 1 : f(XIN)/16 or f(XCIN)/16 1110 : 0 1 0 0 : f(XIN)/32 or f(XCIN)/32 1111 : 0 1 0 1 : f(XIN)/64 or f(XCIN)/64 0 1 1 0 : f(XIN)/128 or f(XCIN)/128 0 1 1 1 : f(XIN)/256 or f(XCIN)/256 1 0 0 0 : f(XIN)/512 or f(XCIN)/512 1 0 0 1 : f(XIN)/1024 or f(XCIN)/1024 Timer X count source selection bits b7b6b5b4 0 0 0 0 : f(XIN)/2 or f(XCIN)/2 0 0 0 1 : f(XIN)/4 or f(XCIN)/4 0 0 1 0 : f(XIN)/8 or f(XCIN)/8 0 0 1 1 : f(XIN)/16 or f(XCIN)/16 0 1 0 0 : f(XIN)/32 or f(XCIN)/32 0 1 0 1 : f(XIN)/64 or f(XCIN)/64 0 1 1 0 : f(XIN)/128 or f(XCIN)/128 0 1 1 1 : f(XIN)/256 or f(XCIN)/256 1 0 0 0 : f(XIN)/512 or f(XCIN)/512 1 0 0 1 : f(XIN)/1024 or f(XCIN)/1024 1 0 1 0 : f(XCIN)
b7 b0
Not used
1011 : 1100 : 1101 : 1110 : 1111 :
Not used
Timer Y, Z count source selection register (TYZCSS : address 000F16) Timer Y count source selection bits b3b2b1b0 0 0 0 0 : f(XIN)/2 or f(XCIN)/2 1011 : 0 0 0 1 : f(XIN)/4 or f(XCIN)/4 1100 : 0 0 1 0 : f(XIN)/8 or f(XCIN)/8 1101 : 0 0 1 1 : f(XIN)/16 or f(XCIN)/16 1110 : 0 1 0 0 : f(XIN)/32 or f(XCIN)/32 1111 : 0 1 0 1 : f(XIN)/64 or f(XCIN)/64 0 1 1 0 : f(XIN)/128 or f(XCIN)/128 0 1 1 1 : f(XIN)/256 or f(XCIN)/256 1 0 0 0 : f(XIN)/512 or f(XCIN)/512 1 0 0 1 : f(XIN)/1024 or f(XCIN)/1024 1 0 1 0 : f(XCIN) Timer Z count source selection bits b7b6b5b4 0 0 0 0 : f(XIN)/2 or f(XCIN)/2 0 0 0 1 : f(XIN)/4 or f(XCIN)/4 0 0 1 0 : f(XIN)/8 or f(XCIN)/8 0 0 1 1 : f(XIN)/16 or f(XCIN)/16 0 1 0 0 : f(XIN)/32 or f(XCIN)/32 0 1 0 1 : f(XIN)/64 or f(XCIN)/64 0 1 1 0 : f(XIN)/128 or f(XCIN)/128 0 1 1 1 : f(XIN)/256 or f(XCIN)/256 1 0 0 0 : f(XIN)/512 or f(XCIN)/512 1 0 0 1 : f(XIN)/1024 or f(XCIN)/1024 1 0 1 0 : f(XCIN)
Not used
1011 : 1100 : 1101 : 1110 : 1111 :
Not used
Fig. 23 Structure of timer 12, X and timer Y, Z count source selection registers
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-31
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
q16-bit Timer
The timer Z is a 16-bit timer. When the timer reaches "000016", an underflow occurs at the next count pulse and the corresponding timer latch is reloaded into the timer and the count is continued. When the timer underflows, the interrupt request bit corresponding to the timer Z is set to "1". When reading/writing to the timer Z, perform reading/writing to both the high-order byte and the low-order byte. When reading the timer Z, read from the high-order byte first, followed by the low-order byte. Do not perform the writing to the timer Z between read operation of the high-order byte and read operation of the low-order byte. When writing to the timer Z, write to the low-order byte first, followed by the high-order byte. Do not perform the reading to the timer Z between write operation of the low-order byte and write operation of the high-order byte. The timer Z can select the count source by the timer Z count source selection bits of timer Y, Z count source selection register (bits 7 to 4 at address 000F16). Timer Z can select one of seven operating modes by setting the timer Z mode register (address 002A16).
(2) Event counter mode
qMode selection This mode can be selected by setting "000" to the timer Z operating mode bits (bits 2 to 0) and setting "1" to the timer/event counter mode switch bit (bit 7) of the timer Z mode register (address 002A16). The valid edge for the count operation depends on the CNTR2 active edge switch bit (bit 5) of the timer Z mode register (address 002A16). When it is "0", the rising edge is valid. When it is "1", the falling edge is valid. qInterrupt The interrupt at an underflow is the same as the timer mode's. qExplanation of operation The operation is the same as the timer mode's. Set the double-function port of CNTR2 pin and port P47 to input in this mode. Figure 26 shows the timing chart of the timer/event counter mode.
(3) Pulse output mode
qMode selection This mode can be selected by setting "001" to the timer Z operating mode bits (bits 2 to 0) and setting "0" to the timer/event counter mode switch bit (b7) of the timer Z mode register (address 002A16). qCount source selection In high- or middle-speed mode, 1/2, 1/4, 1/8, 1/16, 1/32, 1/64, 1/ 128, 1/256, 1/512 or 1/1024 of f(XIN); or f(XCIN) can be selected as the count source. In low-speed mode, 1/2, 1/4, 1/8, 1/16, 1/32, 1/64, 1/128, 1/256, 1/ 512 or 1/1024 of f(XCIN); or f(XCIN) can be selected as the count source. qInterrupt The interrupt at an underflow is the same as the timer mode's. qExplanation of operation The operation is the same as the timer mode's. Moreover the pulse which is inverted each time the timer underflows is output from CNTR2 pin. When the CNTR2 active edge switch bit (bit 5) of the timer Z mode register (address 002A16) is "0", the output starts with "H" level. When it is "1", the output starts with "L" level. sPrecautions The double-function port of CNTR2 pin and port P47 is automatically set to the timer pulse output port in this mode. The output from CNTR2 pin is initialized to the level depending on CNTR2 active edge switch bit by writing to the timer. When the value of the CNTR2 active edge switch bit is changed, the output level of CNTR2 pin is inverted. Figure 27 shows the timing chart of the pulse output mode.
(1) Timer mode
qMode selection This mode can be selected by setting "000" to the timer Z operating mode bits (bits 2 to 0) and setting "0" to the timer/event counter mode switch bit (b7) of the timer Z mode register (address 002A16). qCount source selection In high- or middle-speed mode, 1/2, 1/4, 1/8, 1/16, 1/32, 1/64, 1/ 128, 1/256, 1/512 or 1/1024 of f(XIN); or f(XCIN) can be selected as the count source. In low-speed mode, 1/2, 1/4, 1/8, 1/16, 1/32, 1/64, 1/128, 1/256, 1/ 512 or 1/1024 of f(XCIN); or f(XCIN) can be selected as the count source. qInterrupt When an underflow occurs, the INT0/timer Z interrupt request bit (bit 0) of the interrupt request register 1 (address 003C16) is set to "1". qExplanation of operation During timer stop, usually write data to a latch and a timer at the same time to set the timer value. The timer count operation is started by setting "0" to the timer Z count stop bit (bit 6) of the timer Z mode register (address 002A16). When the timer reaches "000016", an underflow occurs at the next count pulse and the contents of timer latch are reloaded into the timer and the count is continued. When writing data to the timer during operation, the data is written only into the latch. Then the new latch value is reloaded into the timer at the next underflow.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-32
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
(4) Pulse period measurement mode
qMode selection This mode can be selected by setting "010" to the timer Z operating mode bits (bits 2 to 0) and setting "0" to the timer/event counter mode switch bit (b7) of the timer Z mode register (address 002A16). qCount source selection In high- or middle-speed mode, 1/2, 1/4, 1/8, 1/16, 1/32, 1/64, 1/128, 1/256, 1/512 or 1/1024 of f(XIN); or f(XCIN) can be selected as the count source. In low-speed mode, 1/2, 1/4, 1/8, 1/16, 1/32, 1/64, 1/128, 1/256, 1/512 or 1/1024 of f(XCIN); or f(XCIN) can be selected as the count source. qInterrupt The interrupt at an underflow is the same as the timer mode's. When the pulse period measurement is completed, the INT4/ CNTR2 interrupt request bit (bit 5) of the interrupt request register 2 (address 003D16) is set to "1". qExplanation of operation The cycle of the pulse which is input from the CNTR2 pin is measured. When the CNTR2 active edge switch bit (bit 5) of the timer Z mode register (address 002A16) is "0", the timer counts during the term from one falling edge of CNTR2 pin input to the next falling edge. When it is "1", the timer counts during the term from one rising edge input to the next rising edge input. When the valid edge of measurement completion/start is detected, the 1's complement of the timer value is written to the timer latch and "FFFF16" is set to the timer. Furthermore when the timer underflows, the timer Z interrupt request occurs and "FFFF16" is set to the timer. When reading the timer Z, the value of the timer latch (measured value) is read. The measured value is retained until the next measurement completion. sPrecautions Set the double-function port of CNTR2 pin and port P47 to input in this mode. A read-out of timer value is impossible in this mode. The timer can be written to only during timer stop (no measurement of pulse period). Since the timer latch in this mode is specialized for the read-out of measured values, do not perform any write operation during measurement. "FFFF16" is set to the timer when the timer underflows or when the valid edge of measurement start/completion is detected. Consequently, the timer value at start of pulse period measurement depends on the timer value just before measurement start. Figure 28 shows the timing chart of the pulse period measurement mode.
(5) Pulse width measurement mode
qMode selection This mode can be selected by setting "011" to the timer Z operating mode bits (bits 2 to 0) and setting "0" to the timer/event counter mode switch bit (b7) of the timer Z mode register (address 002A16). qCount source selection In high- or middle-speed mode, 1/2, 1/4, 1/8, 1/16, 1/32, 1/64, 1/128, 1/256, 1/512 or 1/1024 of f(XIN); or f(XCIN) can be selected as the count source. In low-speed mode, 1/2, 1/4, 1/8, 1/16, 1/32, 1/64, 1/128, 1/256, 1/512 or 1/1024 of f(XCIN); or f(XCIN) can be selected as the count source. qInterrupt The interrupt at an underflow is the same as the timer mode's. When the pulse widths measurement is completed, the INT4/ CNTR2 interrupt request bit (bit 5) of the interrupt request register 2 (address 003D16) is set to "1". qExplanation of operation The pulse width which is input from the CNTR2 pin is measured. When the CNTR2 active edge switch bit (bit 5) of the timer Z mode register (address 002A16) is "0", the timer counts during the term from one rising edge input to the next falling edge input ("H" term). When it is "1", the timer counts during the term from one falling edge of CNTR2 pin input to the next rising edge of input ("L" term). When the valid edge of measurement completion is detected, the 1's complement of the timer value is written to the timer latch. When the valid edge of measurement completion/start is detected, "FFFF16" is set to the timer. When the timer Z underflows, the timer Z interrupt occurs and "FFFF16" is set to the timer Z. When reading the timer Z, the value of the timer latch (measured value) is read. The measured value is retained until the next measurement completion. sPrecautions Set the double-function port of CNTR2 pin and port P47 to input in this mode. A read-out of timer value is impossible in this mode. The timer can be written to only during timer stop (no measurement of pulse widths). Since the timer latch in this mode is specialized for the read-out of measured values, do not perform any write operation during measurement. "FFFF16" is set to the timer when the timer underflows or when the valid edge of measurement start/completion is detected. Consequently, the timer value at start of pulse width measurement depends on the timer value just before measurement start. Figure 29 shows the timing chart of the pulse width measurement mode.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-33
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
*"L" one-shot pulse; Bit 5 of timer Z mode register = "1" The output level of the CNTR2 pin is initialized to "H" at mode selection. When trigger generation (input signal to INT1 pin) is detected, "L" is output from the CNTR2 pin. When an underflow occurs, "H" is output. The "L" one-shot pulse width is set by the setting value to the timer Z low-order and high-order. When trigger generating is detected during timer count stop, although "L" is output from the CNTR2 pin, "L" output state continues because an underflow does not occur. sPrecautions Set the double-function port of INT1 pin and port P42 to input in this mode. Set the double-function port of CNTR2 pin and port P22 is automatically set to the programmable one-shot generating port in this mode. This mode cannot be used in low-speed mode. If the value of the CNTR2 active edge switch bit is changed during one-shot generating enabled or generating one-shot pulse, then the output level from CNTR2 pin changes. Figure 31 shows the timing chart of the programmable one-shot generating mode.
(6) Programmable waveform generating mode
qMode selection This mode can be selected by setting "100" to the timer Z operating mode bits (bits 2 to 0) and setting "0" to the timer/event counter mode switch bit (b7) of the timer Z mode register (address 002A16). qCount source selection In high- or middle-speed mode, 1/2, 1/4, 1/8, 1/16, 1/32, 1/64, 1/128, 1/256, 1/512 or 1/1024 of f(XIN); or f(XCIN) can be selected as the count source. In low-speed mode, 1/2, 1/4, 1/8, 1/16, 1/32, 1/64, 1/128, 1/256, 1/ 512 or 1/1024 of f(XCIN); or f(XCIN) can be selected as the count source. qInterrupt The interrupt at an underflow is the same as the timer mode's. qExplanation of operation The operation is the same as the timer mode's. Moreover the timer outputs the data set in the output level latch (bit 4) of the timer Z mode register (address 002A16) from the CNTR2 pin each time the timer underflows. Changing the value of the output level latch and the timer latch after an underflow makes it possible to output an optional waveform from the CNTR2 pin. sPrecautions The double-function port of CNTR2 pin and port P47 is automatically set to the programmable waveform generating port in this mode. Figure 30 shows the timing chart of the programmable waveform generating mode.
sNotes regarding all modes
qTimer Z write control Which write control can be selected by the timer Z write control bit (bit 3) of the timer Z mode register (address 002A16), writing data to both the latch and the timer at the same time or writing data only to the latch. When the operation "writing data only to the latch" is selected, the value is set to the timer latch by writing data to the address of timer Z and the timer is updated at next underflow. After reset release, the operation "writing data to both the latch and the timer at the same time" is selected, and the value is set to both the latch and the timer at the same time by writing data to the address of timer Z. In the case of writing data only to the latch, if writing data to the latch and an underflow are performed almost at the same time, the timer value may become undefined. qTimer Z read control A read-out of timer value is impossible in pulse period measurement mode and pulse width measurement mode. In the other modes, a read-out of timer value is possible regardless of count operating or stopped. However, a read-out of timer latch value is impossible. qSwitch of interrupt active edge of CNTR2 and INT1 Each interrupt active edge depends on setting of the CNTR2 active edge switch bit and the INT1 active edge selection bit. qSwitch of count source When switching the count source by the timer Z count source selection bits, the value of timer count is altered in inconsiderable amount owing to generating of thin pulses on the count input signals. Therefore, select the timer count source before setting the value to the prescaler and the timer. qUsage of CNTR2 pin as normal I/O port To use the CNTR2 pin as normal I/O port P47, set timer Z operating mode bits (b2, b1, b0) of timer Z mode register (address 002A16) to "000".
(7) Programmable one-shot generating mode
qMode selection This mode can be selected by setting "101" to the timer Z operating mode bits (bits 2 to 0) and setting "0" to the timer/event counter mode switch bit (b7) of the timer Z mode register (address 002A16). qCount source selection In high- or middle-speed mode, 1/2, 1/4, 1/8, 1/16, 1/32, 1/64, 1/ 128, 1/256, 1/512 or 1/1024 of f(XIN); or f(XCIN) can be selected as the count source. qInterrupt The interrupt at an underflow is the same as the timer mode's. The trigger to generate one-shot pulse can be selected by the INT1 active edge selection bit (bit 1) of the interrupt edge selection register (address 003A16). When it is "0", the falling edge active is selected; when it is "1", the rising edge active is selected. When the valid edge of the INT1 pin is detected, the INT1 interrupt request bit (bit 1) of the interrupt request register 1 (address 003C16) is set to "1". qExplanation of operation *"H" one-shot pulse; Bit 5 of timer Z mode register = "0" The output level of the CNTR2 pin is initialized to "L" at mode selection. When trigger generation (input signal to INT1 pin) is detected, "H" is output from the CNTR2 pin. When an underflow occurs, "L" is output. The "H" one-shot pulse width is set by the setting value to the timer Z register low-order and high-order. When trigger generating is detected during timer count stop, although "H" is output from the CNTR2 pin, "H" output state continues because an underflow does not occur.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-34
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
P42/INT1 Programmable one-shot generating mode
Programmable one-shot generating circuit
CNTR2 active edge Data bus Programmable one-shot switch bit "1" generating mode
"0"
Programmable waveform generating mode Output level latch
D T Q
To INT1 interrupt request bit
Pulse output mode CNTR2 active edge switch bit
S Q T "001" "100" "101" Q "0" "1"
Pulse output mode
Timer Z operating mode bits Port P47 direction register
Timer Z low-order latch Port P47 latch Timer Z low-order
Timer Z high-order latch Timer Z high-order To timer Z interrupt request bit
Pulse period measurement mode Pulse width measurement mode
Edge detection circuit
"1"
"1"
To CNTR2 interrupt request bit
Clock for timer Z
P47/CNTR2
"0"
f(XCIN) "0"
CNTR2 active edge switch bit
XIN
Timer/Event counter mode switch bit
Timer Z count stop bit
XCIN
Count source Divider selection bit (1/2, 1/4, 1/8, 1/16, 1/32, 1/64, 1/128, 1/256, 1/512, 1/1024)
Fig. 24 Block diagram of timer Z
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-35
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
b7
b0
Timer Z mode register (TZM : address 002A16) Timer Z operating mode bits b2b1b0 0 0 0 : Timer/Event counter mode 0 0 1 : Pulse output mode 0 1 0 : Pulse period measurement mode 0 1 1 : Pulse width measurement mode 1 0 0 : Programmable waveform generating mode 1 0 1 : Programmable one-shot generating mode 1 1 0 : Not available 1 1 1 : Not available Timer Z write control bit 0 : Writing data to both latch and timer simultaneously 1 : Writing data only to latch Output level latch 0 : "L" output 1 : "H" output CNTR2 active edge switch bit 0 : *Event counter mode: Count at rising edge *Pulse output mode: Start outputting "H" *Pulse period measurement mode: Measurement between two falling edges *Pulse width measurement mode: Measurement of "H" term *Programmable one-shot generating mode: After start outputting "L", "H" one-shot pulse generated *Interrupt at falling edge 1 : *Event counter mode: Count at falling edge *Pulse output mode: Start outputting "L" *Pulse period measurement mode: Measurement between two rising edges *Pulse width measurement mode: Measurement of "L" term *Programmable one-shot generating mode: After start outputting "H", "L" one-shot pulse generated *Interrupt at rising edge Timer Z count stop bit 0 : Count start 1 : Count stop Timer/Event counter mode switch bit (Note) 0 : Timer mode 1 : Event counter mode Note: When selecting the modes except the timer/event counter mode, set "0" to this bit.
Fig. 25 Structure of timer Z mode register
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-36
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
FFFF16 TL
000016 TR TR TR
TL : Value set to timer latch TR : Timer interrupt request
Fig. 26 Timing chart of timer/event counter mode
FFFF16
TL
000016 TR TR TR TR
Waveform output from CNTR2 pin CNTR2 CNTR2 TL : Value set to timer latch TR : Timer interrupt request CNTR2 : CNTR2 interrupt request (CNTR2 active edge switch bit = "0"; Falling edge active)
Fig. 27 Timing chart of pulse output mode
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-37
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
000016 T3 T2 T1 FFFF16 TR FFFF16 + T1 Signal input from CNTR2 pin CNTR2 CNTR2 CNTR2 of rising edge active TR : Timer interrupt request CNTR2 : CNTR2 interrupt request
Fig. 28 Timing chart of pulse period measurement mode (Measuring term between two rising edges)
TR T2 T3 FFFF16
CNTR2
CNTR2
000016 T3 T2 T1 FFFF16 TR
Signal input from CNTR2 pin
FFFF16 + T2
T3
T1
CNTR2 CNTR2 CNTR2 CNTR2 interrupt of rising edge active; Measurement of "L" width TR : Timer interrupt request CNTR2 : CNTR2 interrupt request
Fig. 29 Timing chart of pulse width measurement mode (Measuring "L" term)
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-38
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
FFFF16 T3 L T2 T1 000016
Signal output from CNTR2 pin
L TR
T1
T3
T2
TR TR TR CNTR2 CNTR2 L : Timer initial value TR : Timer interrupt request CNTR2 : CNTR2 interrupt request (CNTR2 active edge switch bit = "0"; Falling edge active)
Fig. 30 Timing chart of programmable waveform generating mode
FFFF16
L
Signal input from INT1 pin Signal output from CNTR2 pin
TR
TR
TR
L CNTR2
L CNTR2
L
L : One-shot pulse width TR : Timer interrupt request CNTR2 : CNTR2 interrupt request (CNTR2 active edge switch bit = "0"; Falling edge active)
Fig. 31 Timing chart of programmable one-shot generating mode ("H" one-shot pulse generating)
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-39
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
SERIAL INTERFACE Serial I/O1
Serial I/O1 can be used as either clock synchronous or asynchronous (UART) serial I/O1. A dedicated timer is also provided for baud rate generation.
(1) Clock Synchronous Serial I/O Mode
Clock synchronous serial I/O1 mode can be selected by setting the serial I/O1 mode selection bit of the serial I/O1 control register (bit 6 of address 001A16) to "1". For clock synchronous serial I/O, the transmitter and the receiver must use the same clock. If an internal clock is used, transfer is started by a write signal to the transmit/receive buffer register.
Data bus Serial I/O1 control register Address 001A16
Address 001816
Receive buffer register 1
Receive buffer full flag (RBF) Receive interrupt request (RI) Clock control circuit
P44/RXD1
Receive shift register 1
Shift clock P46/SCLK1
BRG count source selection bit f(XIN) (f(XCIN) in low-speed mode) 1/4 P47/SRDY1 F/F Falling-edge detector
Serial I/O1 synchronous clock selection bit Frequency division ratio 1/(n+1) Baud rate generator 1 Address 001C16 1/4
Clock control circuit Shift clock Transmit shift completion flag (TSC) Transmit interrupt source selection bit Transmit interrupt request (TI) Transmit buffer empty flag (TBE) Serial I/O1 status register Address 001916
P45/TXD1
Transmit shift register 1 Transmit buffer register 1
Address 001816 Data bus
Fig. 32 Block diagram of clock synchronous serial I/O1
Transfer shift clock (1/2 to 1/2048 of the internal clock, or an external clock) Serial output TxD1 Serial input RxD1 D0 D0 D1 D1 D2 D2 D3 D3 D4 D4 D5 D5 D6 D6 D7 D7
Receive enable signal SRDY1 Write pulse to receive/transmit buffer register (address 001816) TBE = 0 RBF = 1 TSC = 1 Overrun error (OE) detection
TBE = 1 TSC = 0
Notes 1: As the transmit interrupt (TI), which can be selected, either when the transmit buffer has emptied (TBE=1) or after the transmit shift operation has ended (TSC=1), by setting the transmit interrupt source selection bit (TIC) of the serial I/O1 control register. 2: If data is written to the transmit buffer register when TSC=0, the transmit clock is generated continuously and serial data is output continuously from the TxD pin. 3: The receive interrupt (RI) is set when the receive buffer full flag (RBF) becomes "1" .
Fig. 33 Operation of clock synchronous serial I/O1
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-40
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
two buffers have the same address in a memory. Since the shift register cannot be written to or read from directly, transmit data is written to the transmit buffer register, and receive data is read from the receive buffer register. The transmit buffer register can also hold the next data to be transmitted, and the receive buffer register can hold a character while the next character is being received.
(2) Asynchronous Serial I/O (UART) Mode
Clock asynchronous serial I/O mode (UART) can be selected by clearing the serial I/O1 mode selection bit of the serial I/O1 control register to "0". Eight serial data transfer formats can be selected, and the transfer formats used by a transmitter and receiver must be identical. The transmit and receive shift registers each have a buffer, but the
Data bus Address 001816 OE Receive buffer register 1 Character length selection bit ST detector 7 bits Receive shift register 1 8 bits PE FE SP detector Clock control circuit Serial I/O1 synchronous clock selection bit P46/SCLK1 BRG count source selection bit Frequency division ratio 1/(n+1) f(XIN) Baud rate generator (f(XCIN) in low-speed mode) Address 001C16 1/4 ST/SP/PA generator 1/16 P45/TXD1 Character length selection bit
Transmit buffer register 1 Transmit shift register 1
Serial I/O1 control register Address 001A16 Receive buffer full flag (RBF) Receive interrupt request (RI) 1/16 UART1 control register Address 001B16
P44/RXD1
Transmit shift completion flag (TSC) Transmit interrupt source selection bit Transmit interrupt request (TI) Transmit buffer empty flag (TBE) Serial I/O1 status register Address 001916
Address 001816 Data bus
Fig. 34 Block diagram of UART serial I/O1
Transmit or receive clock
Transmit buffer write signal TBE=0 TSC=0 TBE=1 Serial output TXD1 ST TBE=0 TBE=1 TSC=1
D0
D1 1 start bit 7 or 8 data bit 1 or 0 parity bit 1 or 2 stop bit (s)
SP
ST
D0
D1
SP Generated at 2nd bit in 2-stop-bit mode
Receive buffer read signal
RBF=0 RBF=1 RBF=1
Serial input RXD1
ST
D0
D1
SP
ST
D0
D1
SP
Notes 1: Error flag detection occurs at the same time that the RBF flag becomes "1" (at 1st stop bit, during reception). 2: As the transmit interrupt (TI), when either the TBE or TSC flag becomes "1," can be selected to occur depending on the setting of the transmit interrupt source selection bit (TIC) of the serial I/O1 control register. 3: The receive interrupt (RI) is set when the RBF flag becomes "1." 4: After data is written to the transmit buffer when TSC=1, 0.5 to 1.5 cycles of the data shift cycle are necessary until changing to TSC=0.
Fig. 35 Operation of UART serial I/O1
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-41
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
[Serial I/O1 Control Register (SIO1CON)] 001A16
The serial I/O1 control register consists of eight control bits for the serial I/O1 function.
[UART1 Control Register (UART1CON)] 001B16
The UART control register consists of four control bits (bits 0 to 3) which are valid when asynchronous serial I/O is selected and set the data format of an data transfer, and one bit (bit 4) which is always valid and sets the output structure of the P45/TXD1 pin.
[Serial I/O1 Status Register (SIO1STS)] 001916
The read-only serial I/O1 status register consists of seven flags (bits 0 to 6) which indicate the operating status of the serial I/O1 function and various errors. Three of the flags (bits 4 to 6) are valid only in UART mode. The receive buffer full flag (bit 1) is cleared to "0" when the receive buffer register is read. If there is an error, it is detected at the same time that data is transferred from the receive shift register to the receive buffer register, and the receive buffer full flag is set. A write to the serial I/O1 status register clears all the error flags OE, PE, FE, and SE (bit 3 to bit 6, respectively). Writing "0" to the serial I/O1 enable bit SIOE (bit 7 of the serial I/O1 control register) also clears all the status flags, including the error flags. Bits 0 to 6 of the serial I/O1 status register are initialized to "0" at reset, but if the transmit enable bit (bit 4) of the serial I/O1 control register has been set to "1", the transmit shift completion flag (bit 2) and the transmit buffer empty flag (bit 0) become "1".
[Transmit Buffer Register 1/Receive Buffer Register 1 (TB1/RB1)] 001816
The transmit buffer register 1 and the receive buffer register 1 are located at the same address. The transmit buffer is write-only and the receive buffer is read-only. If a character bit length is 7 bits, the MSB of data stored in the receive buffer is "0".
[Baud Rate Generator 1 (BRG1)] 001C16
The baud rate generator determines the baud rate for serial transfer. The baud rate generator divides the frequency of the count source by 1/(n + 1), where n is the value written to the baud rate generator.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-42
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
b7
b0
Serial I/O1 status register (SIO1STS : address 001916) Transmit buffer empty flag (TBE) 0: Buffer full 1: Buffer empty Receive buffer full flag (RBF) 0: Buffer empty 1: Buffer full Transmit shift completion flag (TSC) 0: Transmit shift in progress 1: Transmit shift completed Overrun error flag (OE) 0: No error 1: Overrun error Parity error flag (PE) 0: No error 1: Parity error Framing error flag (FE) 0: No error 1: Framing error Summing error flag (SE) 0: (OE) U (PE) U (FE)=0 1: (OE) U (PE) U (FE)=1 Not used (returns "1" when read)
b7
b0
Serial I/O1 control register (SIO1CON : address 001A16) BRG count source selection bit (CSS) 0: f(XIN) (f(XCIN) in low-speed mode) 1: f(XIN)/4 (f(XCIN)/4 in low-speed mode) Serial I/O1 synchronous clock selection bit (SCS) 0: BRG output divided by 4 when clock synchronous serial I/O is selected, BRG output divided by 16 when UART is selected. 1: External clock input when clock synchronous serial I/O is selected, external clock input divided by 16 when UART is selected. SRDY1 output enable bit (SRDY) 0: P47 pin operates as normal I/O pin 1: P47 pin operates as SRDY1 output pin Transmit interrupt source selection bit (TIC) 0: Interrupt when transmit buffer has emptied 1: Interrupt when transmit shift operation is completed Transmit enable bit (TE) 0: Transmit disabled 1: Transmit enabled Receive enable bit (RE) 0: Receive disabled 1: Receive enabled Serial I/O1 mode selection bit (SIOM) 0: Clock asynchronous (UART) serial I/O 1: Clock synchronous serial I/O Serial I/O1 enable bit (SIOE) 0: Serial I/O1 disabled (pins P44 to P47 operate as normal I/O pins) 1: Serial I/O1 enabled (pins P44 to P47 operate as serial I/O pins)
b7
b0
UART1 control register (UART1CON : address 001B16) Character length selection bit (CHAS) 0: 8 bits 1: 7 bits Parity enable bit (PARE) 0: Parity checking disabled 1: Parity checking enabled Parity selection bit (PARS) 0: Even parity 1: Odd parity Stop bit length selection bit (STPS) 0: 1 stop bit 1: 2 stop bits P45/TXD1 P-channel output disable bit (POFF) 0: CMOS output (in output mode) 1: N-channel open drain output (in output mode) Not used (return "1" when read)
Fig. 36 Structure of serial I/O1 control registers
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-43
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
2. Notes when selecting clock asynchronous serial I/O 2.1 Stop of transmission operation q Note Clear the transmit enable bit to "0" (transmit disabled). The transmission operation does not stop by clearing the serial I/O1 enable bit to "0". q Reason Since transmission is not stopped and the transmission circuit is not initialized even if only the serial I/O1 enable bit is cleared to "0" (serial I/O disabled), the internal transmission is running (in this case, since pins TxD1, RxD1, SCLK1, and SRDY1 function as I/O ports, the transmission data is not output). When data is written to the transmit buffer register in this state, data starts to be shifted to the transmit shift register. When the serial I/O1 enable bit is set to "1" at this time, the data during internally shifting is output to the TxD1 pin and an operation failure occurs. 2.2 Stop of receive operation q Note Clear the receive enable bit to "0" (receive disabled). 2.3 Stop of transmit/receive operation q Note 1 (only transmission operation is stopped) Clear the transmit enable bit to "0" (transmit disabled). The transmission operation does not stop by clearing the serial I/O1 enable bit to "0". q Reason Since transmission is not stopped and the transmission circuit is not initialized even if only the serial I/O1 enable bit is cleared to "0" (serial I/O disabled), the internal transmission is running (in this case, since pins TxD1, RxD1, SCLK1, and SRDY1 function as I/O ports, the transmission data is not output). When data is written to the transmit buffer register in this state, data starts to be shifted to the transmit shift register. When the serial I/O1 enable bit is set to "1" at this time, the data during internally shifting is output to the TxD1 pin and an operation failure occurs. q Note 2 (only receive operation is stopped) Clear the receive enable bit to "0" (receive disabled).
s Notes concerning serial I/O1
1. Notes when selecting clock synchronous serial I/O 1.1 Stop of transmission operation q Note Clear the serial I/O1 enable bit and the transmit enable bit to "0" (serial I/O and transmit disabled). q Reason Since transmission is not stopped and the transmission circuit is not initialized even if only the serial I/O1 enable bit is cleared to "0" (serial I/O disabled), the internal transmission is running (in this case, since pins TxD1, RxD1, SCLK1, and SRDY1 function as I/O ports, the transmission data is not output). When data is written to the transmit buffer register in this state, data starts to be shifted to the transmit shift register. When the serial I/O1 enable bit is set to "1" at this time, the data during internally shifting is output to the TxD1 pin and an operation failure occurs. 1.2 Stop of receive operation q Note Clear the receive enable bit to "0" (receive disabled), or clear the serial I/O1 enable bit to "0" (serial I/O disabled). 1.3 Stop of transmit/receive operation q Note Clear both the transmit enable bit and receive enable bit to "0" (transmit and receive disabled). (when data is transmitted and received in the clock synchronous serial I/O mode, any one of data transmission and reception cannot be stopped.) q Reason In the clock synchronous serial I/O mode, the same clock is used for transmission and reception. If any one of transmission and reception is disabled, a bit error occurs because transmission and reception cannot be synchronized. In this mode, the clock circuit of the transmission circuit also operates for data reception. Accordingly, the transmission circuit does not stop by clearing only the transmit enable bit to "0" (transmit disabled). Also, the transmission circuit is not initialized by clearing the serial I/O1 enable bit to "0" (serial I/O disabled) (refer to 1.1).
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-44
HARDWARE 3804 Group (Spec.H)
3. SRDY1 output of reception side q Note When signals are output from the SRDY1 pin on the reception side by using an external clock in the clock synchronous serial I/O mode, set all of the receive enable bit, the SRDY1 output enable bit, and the transmit enable bit to "1" (transmit enabled). 4. Setting serial I/O1 control register again q Note Set the serial I/O1 control register again after the transmission and the reception circuits are reset by clearing both the transmit enable bit and the receive enable bit to "0." Clear both the transmit enable bit (TE) and the receive enable bit (RE) to "0"
FUNCTIONAL DESCRIPTION
7. Transmit interrupt request when transmit enable bit is set q Note When using the transmit interrupt, take the following sequence. Set the serial I/O1 transmit interrupt enable bit to "0" (disabled). Set the transmit enable bit to "1". Set the serial I/O1 transmit interrupt request bit to "0" after 1 or more instruction has executed. Set the serial I/O1 transmit interrupt enable bit to "1" (enabled). q Reason When the transmit enable bit is set to "1", the transmit buffer empty flag and the transmit shift register shift completion flag are also set to "1". Therefore, regardless of selecting which timing for the generating of transmit interrupts, the interrupt request is generated and the transmit interrupt request bit is set at this point.
Set the bits 0 to 3 and bit 6 of the serial I/O control register
Set both the transmit enable bit (TE) and the receive enable bit (RE), or one of them to "1"
Can be set with the LDM instruction at the same time
5. Data transmission control with referring to transmit shift register completion flag q Note After the transmit data is written to the transmit buffer register, the transmit shift register completion flag changes from "1" to "0" with a delay of 0.5 to 1.5 shift clocks. When data transmission is controlled with referring to the flag after writing the data to the transmit buffer register, note the delay. 6. Transmission control when external clock is selected q Note When an external clock is used as the synchronous clock for data transmission, set the transmit enable bit to "1" at "H" of the SCLK1 input level. Also, write data to the transmit buffer register at "H" of the SCLK1 input level.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-45
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
Serial I/O2
The serial I/O2 function can be used only for clock synchronous serial I/O2. For clock synchronous serial I/O2, the transmitter and the receiver must use the same clock. If the internal clock is used, transfer is started by a write signal to the serial I/O2 register.
b7
b0
Serial I/O2 control register (SIO2CON : address 001D16) Internal synchronous clock selection bits
b2 b1 b0
[Serial I/O2 Control Register (SIO2CON)] 001D16
The serial I/O2 control register contains eight bits which control various serial I/O2 functions.
0 0 0: f(XIN)/8 (f(XCIN)/8 in low-speed mode) 0 0 1: f(XIN)/16 (f(XCIN)/16 in low-speed mode) 0 1 0: f(XIN)/32 (f(XCIN)/32 in low-speed mode) 0 1 1: f(XIN)/64 (f(XCIN)/64 in low-speed mode) 1 1 0: f(XIN)/128 (f(XCIN)/128 in low-speed mode) 1 1 1: f(XIN)/256 (f(XCIN)/256 in low-speed mode) Serial I/O2 port selection bit 0: I/O port 1: SOUT2,SCLK2 signal output SRDY2 output enable bit 0: I/O port 1: SRDY2 signal output Transfer direction selection bit 0: LSB first 1: MSB first Serial I/O2 synchronous clock selection bit 0: External clock 1: Internal clock P51/SOUT2 P-channel output disable bit 0: CMOS output (in output mode) 1: N-channel open drain output (in output mode)
Fig. 37 Structure of serial I/O2 control register
1/8 1/16
Divider
Internal synchronous clock selection bits
f(XIN) (f(XCIN) in low-speed mode)
1/32 1/64 1/128 1/256
Data bus
P53 latch
"0"
P53/SRDY2
Serial I/O2 synchronous clock selection bit "1"
Synchronization circuit
SCLK2
SRDY2 "1" SRDY2 output enable bit
"0" External clock
P52 latch
"0"
P52/SCLK2
"1" Serial I/O2 port selection bit
Serial I/O counter 2 (3)
Serial I/O2 interrupt request
P51 latch
"0"
P51/SOUT2
"1" Serial I/O2 port selection bit
P50/SIN2
Serial I/O2 register (8)
Address 001F16
Fig. 38 Block diagram of serial I/O2
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-46
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
Transfer clock (Note 1) Serial I/O2 register write signal
(Note 2)
Serial I/O2 output SOUT2 Serial I/O2 input SIN2
D0
D1
D2
D3
D4
D5
D6
D7
Receive enable signal SRDY2
Serial I/O2 interrupt request bit set Notes 1: When the internal clock is selected as the transfer clock, the divide ratio of f(XIN), or f(XCIN) in low-speed mode, can be selected by setting bits 0 to 2 of the serial I/O2 control register. 2: When the internal clock is selected as the transfer clock, the SOUT2 pin goes to high impedance after transfer completion.
Fig. 39 Timing of serial I/O2
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-47
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
Serial I/O3
Serial I/O3 can be used as either clock synchronous or asynchronous (UART) serial I/O3. A dedicated timer is also provided for baud rate generation.
(1) Clock Synchronous Serial I/O Mode
Clock synchronous serial I/O3 mode can be selected by setting the serial I/O3 mode selection bit of the serial I/O3 control register (bit 6 of address 003216) to "1". For clock synchronous serial I/O, the transmitter and the receiver must use the same clock. If an internal clock is used, transfer is started by a write signal to the transmit/receive buffer register.
Data bus Serial I/O3 control register Address 003216
Address 003016
Receive buffer register 3
Receive buffer full flag (RBF) Receive interrupt request (RI) Clock control circuit
P34/RXD3
Receive shift register 3
Shift clock P36/SCLK3
BRG count source selection bit f(XIN) (f(XCIN) in low-speed mode) 1/4 P37/SRDY3 F/F Falling-edge detector
Serial I/O3 synchronous clock selection bit Frequency division ratio 1/(n+1) Baud rate generator 3 Address 002F16 1/4
Clock control circuit Shift clock Transmit shift completion flag (TSC) Transmit interrupt source selection bit Transmit interrupt request (TI) Transmit buffer empty flag (TBE) Serial I/O3 status register Address 003116
P35/TXD3
Transmit shift register 3 Transmit buffer register 3
Address 003016 Data bus
Fig. 40 Block diagram of clock synchronous serial I/O3
Transfer shift clock (1/2 to 1/2048 of the internal clock, or an external clock) Serial output TxD3 Serial input RxD3 D0 D0 D1 D1 D2 D2 D3 D3 D4 D4 D5 D5 D6 D6 D7 D7
Receive enable signal SRDY3 Write pulse to receive/transmit buffer register (address 003016) TBE = 0 RBF = 1 TSC = 1 Overrun error (OE) detection
TBE = 1 TSC = 0
Notes 1: As the transmit interrupt (TI), which can be selected, either when the transmit buffer has emptied (TBE=1) or after the transmit shift operation has ended (TSC=1), by setting the transmit interrupt source selection bit (TIC) of the serial I/O3 control register. 2: If data is written to the transmit buffer register when TSC=0, the transmit clock is generated continuously and serial data is output continuously from the TxD pin. 3: The receive interrupt (RI) is set when the receive buffer full flag (RBF) becomes "1" .
Fig. 41 Operation of clock synchronous serial I/O3
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-48
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
two buffers have the same address in a memory. Since the shift register cannot be written to or read from directly, transmit data is written to the transmit buffer register, and receive data is read from the receive buffer register. The transmit buffer register can also hold the next data to be transmitted, and the receive buffer register can hold a character while the next character is being received.
(2) Asynchronous Serial I/O (UART) Mode
Clock asynchronous serial I/O mode (UART) can be selected by clearing the serial I/O3 mode selection bit of the serial I/O3 control register to "0". Eight serial data transfer formats can be selected, and the transfer formats used by a transmitter and receiver must be identical. The transmit and receive shift registers each have a buffer, but the
Data bus Address 003016
Receive buffer register 3 OE Character length selection bit ST detector 7 bits Receive shift register 3
Serial I/O3 control register Address 003216 Receive buffer full flag (RBF) Receive interrupt request (RI) 1/16
P34/RXD3
8 bits PE FE SP detector Clock control circuit Serial I/O3 synchronous clock selection bit P36/SCLK3 BRG count source selection bit Frequency division ratio 1/(n+1) f(XIN) Baud rate generator 3 (f(XCIN) in low-speed mode) Address 002F16 1/4 ST/SP/PA generator 1/16 P35/TXD3 Character length selection bit
Transmit buffer register 3 Transmit shift register 3
UART3 control register
Address 003316
Transmit shift completion flag (TSC) Transmit interrupt source selection bit Transmit interrupt request (TI) Transmit buffer empty flag (TBE) Serial I/O3 status register Address 003116
Address 003016 Data bus
Fig. 42 Block diagram of UART serial I/O3
Transmit or receive clock
Transmit buffer write signal TBE=0 TSC=0 TBE=1 Serial output TXD3 ST TBE=0 TBE=1 TSC=1
D0
D1 1 start bit 7 or 8 data bit 1 or 0 parity bit 1 or 2 stop bit (s)
SP
ST
D0
D1
SP Generated at 2nd bit in 2-stop-bit mode
Receive buffer read signal
RBF=0 RBF=1 RBF=1
Serial input RXD3
ST
D0
D1
SP
ST
D0
D1
SP
Notes 1: Error flag detection occurs at the same time that the RBF flag becomes "1" (at 1st stop bit, during reception). 2: As the transmit interrupt (TI), when either the TBE or TSC flag becomes "1," can be selected to occur depending on the setting of the transmit interrupt source selection bit (TIC) of the serial I/O3 control register. 3: The receive interrupt (RI) is set when the RBF flag becomes "1." 4: After data is written to the transmit buffer when TSC=1, 0.5 to 1.5 cycles of the data shift cycle are necessary until changing to TSC=0.
Fig. 43 Operation of UART serial I/O3
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-49
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
[Serial I/O3 Control Register (SIO3CON)] 003216
The serial I/O3 control register consists of eight control bits for the serial I/O3 function.
[UART3 Control Register (UART3CON)] 003316
The UART control register consists of four control bits (bits 0 to 3) which are valid when asynchronous serial I/O is selected and set the data format of an data transfer, and one bit (bit 4) which is always valid and sets the output structure of the P35/TXD3 pin.
[Serial I/O3 Status Register (SIO3STS)] 003116
The read-only serial I/O3 status register consists of seven flags (bits 0 to 6) which indicate the operating status of the serial I/O3 function and various errors. Three of the flags (bits 4 to 6) are valid only in UART mode. The receive buffer full flag (bit 1) is cleared to "0" when the receive buffer register is read. If there is an error, it is detected at the same time that data is transferred from the receive shift register to the receive buffer register, and the receive buffer full flag is set. A write to the serial I/O3 status register clears all the error flags OE, PE, FE, and SE (bit 3 to bit 6, respectively). Writing "0" to the serial I/O3 enable bit SIOE (bit 7 of the serial I/O3 control register) also clears all the status flags, including the error flags. Bits 0 to 6 of the serial I/O3 status register are initialized to "0" at reset, but if the transmit enable bit (bit 4) of the serial I/O3 control register has been set to "1", the transmit shift completion flag (bit 2) and the transmit buffer empty flag (bit 0) become "1".
[Transmit Buffer Register 3/Receive Buffer Register 3 (TB3/RB3)] 003016
The transmit buffer register 3 and the receive buffer register 3 are located at the same address. The transmit buffer is write-only and the receive buffer is read-only. If a character bit length is 7 bits, the MSB of data stored in the receive buffer is "0".
[Baud Rate Generator 3 (BRG3)] 002F16
The baud rate generator determines the baud rate for serial transfer. The baud rate generator divides the frequency of the count source by 1/(n + 1), where n is the value written to the baud rate generator.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-50
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
b7
b0
Serial I/O3 status register (SIO3STS : address 003116) Transmit buffer empty flag (TBE) 0: Buffer full 1: Buffer empty Receive buffer full flag (RBF) 0: Buffer empty 1: Buffer full Transmit shift completion flag (TSC) 0: Transmit shift in progress 1: Transmit shift completed Overrun error flag (OE) 0: No error 1: Overrun error Parity error flag (PE) 0: No error 1: Parity error Framing error flag (FE) 0: No error 1: Framing error Summing error flag (SE) 0: (OE) U (PE) U (FE)=0 1: (OE) U (PE) U (FE)=1 Not used (returns "1" when read)
b7
b0
Serial I/O3 control register (SIO3CON : address 003216) BRG count source selection bit (CSS) 0: f(XIN) (f(XCIN) in low-speed mode) 1: f(XIN)/4 (f(XCIN)/4 in low-speed mode) Serial I/O3 synchronous clock selection bit (SCS) 0: BRG output divided by 4 when clock synchronous serial I/O is selected, BRG output divided by 16 when UART is selected. 1: External clock input when clock synchronous serial I/O is selected, external clock input divided by 16 when UART is selected. SRDY3 output enable bit (SRDY) 0: P37 pin operates as normal I/O pin 1: P37 pin operates as SRDY3 output pin Transmit interrupt source selection bit (TIC) 0: Interrupt when transmit buffer has emptied 1: Interrupt when transmit shift operation is completed Transmit enable bit (TE) 0: Transmit disabled 1: Transmit enabled Receive enable bit (RE) 0: Receive disabled 1: Receive enabled Serial I/O3 mode selection bit (SIOM) 0: Clock asynchronous (UART) serial I/O 1: Clock synchronous serial I/O Serial I/O3 enable bit (SIOE) 0: Serial I/O disabled (pins P34 to P37 operate as normal I/O pins) 1: Serial I/O enabled (pins P34 to P37 operate as serial I/O pins)
b7
b0
UART3 control register (UART3CON : address 003316) Character length selection bit (CHAS) 0: 8 bits 1: 7 bits Parity enable bit (PARE) 0: Parity checking disabled 1: Parity checking enabled Parity selection bit (PARS) 0: Even parity 1: Odd parity Stop bit length selection bit (STPS) 0: 1 stop bit 1: 2 stop bits P35/TXD3 P-channel output disable bit (POFF) 0: CMOS output (in output mode) 1: N-channel open drain output (in output mode) Not used (return "1" when read)
Fig. 44 Structure of serial I/O3 control registers
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-51
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
2. Notes when selecting clock asynchronous serial I/O 2.1 Stop of transmission operation q Note Clear the transmit enable bit to "0" (transmit disabled). The transmission operation does not stop by clearing the serial I/O3 enable bit to "0". q Reason Since transmission is not stopped and the transmission circuit is not initialized even if only the serial I/O3 enable bit is cleared to "0" (serial I/O disabled), the internal transmission is running (in this case, since pins TxD3, RxD3, SCLK3, and SRDY3 function as I/O ports, the transmission data is not output). When data is written to the transmit buffer register in this state, data starts to be shifted to the transmit shift register. When the serial I/O3 enable bit is set to "1" at this time, the data during internally shifting is output to the TxD3 pin and an operation failure occurs. 2.2 Stop of receive operation q Note Clear the receive enable bit to "0" (receive disabled). 2.3 Stop of transmit/receive operation q Note 1 (only transmission operation is stopped) Clear the transmit enable bit to "0" (transmit disabled). The transmission operation does not stop by clearing the serial I/O3 enable bit to "0". q Reason Since transmission is not stopped and the transmission circuit is not initialized even if only the serial I/O3 enable bit is cleared to "0" (serial I/O disabled), the internal transmission is running (in this case, since pins TxD3, RxD3, SCLK3, and SRDY3 function as I/O ports, the transmission data is not output). When data is written to the transmit buffer register in this state, data starts to be shifted to the transmit shift register. When the serial I/O3 enable bit is set to "1" at this time, the data during internally shifting is output to the TxD3 pin and an operation failure occurs. q Note 2 (only receive operation is stopped) Clear the receive enable bit to "0" (receive disabled).
s Notes concerning serial I/O3
1. Notes when selecting clock synchronous serial I/O 1.1 Stop of transmission operation q Note Clear the serial I/O3 enable bit and the transmit enable bit to "0" (serial I/O and transmit disabled). q Reason Since transmission is not stopped and the transmission circuit is not initialized even if only the serial I/O3 enable bit is cleared to "0" (serial I/O disabled), the internal transmission is running (in this case, since pins TxD3, RxD3, SCLK3, and SRDY3 function as I/O ports, the transmission data is not output). When data is written to the transmit buffer register in this state, data starts to be shifted to the transmit shift register. When the serial I/O enable bit is set to "1" at this time, the data during internally shifting is output to the TxD3 pin and an operation failure occurs. 1.2 Stop of receive operation q Note Clear the receive enable bit to "0" (receive disabled), or clear the serial I/O3 enable bit to "0" (serial I/O disabled). 1.3 Stop of transmit/receive operation q Note Clear both the transmit enable bit and receive enable bit to "0" (transmit and receive disabled). (when data is transmitted and received in the clock synchronous serial I/O mode, any one of data transmission and reception cannot be stopped.) q Reason In the clock synchronous serial I/O mode, the same clock is used for transmission and reception. If any one of transmission and reception is disabled, a bit error occurs because transmission and reception cannot be synchronized. In this mode, the clock circuit of the transmission circuit also operates for data reception. Accordingly, the transmission circuit does not stop by clearing only the transmit enable bit to "0" (transmit disabled). Also, the transmission circuit is not initialized by clearing the serial I/O3 enable bit to "0" (serial I/O disabled) (refer to 1.1).
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-52
HARDWARE 3804 Group (Spec.H)
3. SRDY3 output of reception side q Note When signals are output from the SRDY3 pin on the reception side by using an external clock in the clock synchronous serial I/O mode, set all of the receive enable bit, the SRDY3 output enable bit, and the transmit enable bit to "1" (transmit enabled). 4. Setting serial I/O3 control register again q Note Set the serial I/O3 control register again after the transmission and the reception circuits are reset by clearing both the transmit enable bit and the receive enable bit to "0." Clear both the transmit enable bit (TE) and the receive enable bit (RE) to "0"
FUNCTIONAL DESCRIPTION
7. Transmit interrupt request when transmit enable bit is set q Note When using the transmit interrupt, take the following sequence. Set the serial I/O3 transmit interrupt enable bit to "0" (disabled). Set the transmit enable bit to "1". Set the serial I/O3 transmit interrupt request bit to "0" after 1 or more instruction has executed. Set the serial I/O3 transmit interrupt enable bit to "1" (enabled). q Reason When the transmit enable bit is set to "1", the transmit buffer empty flag and the transmit shift register shift completion flag are also set to "1". Therefore, regardless of selecting which timing for the generating of transmit interrupts, the interrupt request is generated and the transmit interrupt request bit is set at this point.
Set the bits 0 to 3 and bit 6 of the serial I/O3 control register
Set both the transmit enable bit (TE) and the receive enable bit (RE), or one of them to "1"
Can be set with the LDM instruction at the same time
5. Data transmission control with referring to transmit shift register completion flag q Note After the transmit data is written to the transmit buffer register, the transmit shift register completion flag changes from "1" to "0" with a delay of 0.5 to 1.5 shift clocks. When data transmission is controlled with referring to the flag after writing the data to the transmit buffer register, note the delay. 6. Transmission control when external clock is selected q Note When an external clock is used as the synchronous clock for data transmission, set the transmit enable bit to "1" at "H" of the SCLK3 input level. Also, write data to the transmit buffer register at "H" of the SCLK input level.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-53
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
PULSE WIDTH MODULATION (PWM)
The 3804 group (Spec. H) has PWM functions with an 8-bit resolution, based on a signal that is the clock input XIN or that clock input divided by 2 or the clock input XCIN or that clock input divided by 2 in low-speed mode.
PWM Operation
When bit 0 (PWM enable bit) of the PWM control register is set to "1", operation starts by initializing the PWM output circuit, and pulses are output starting at an "H". If the PWM register or PWM prescaler is updated during PWM output, the pulses will change in the cycle after the one in which the change was made.
Data Setting
The PWM output pin also functions as port P56. Set the PWM period by the PWM prescaler, and set the "H" term of output pulse by the PWM register. If the value in the PWM prescaler is n and the value in the PWM register is m (where n = 0 to 255 and m = 0 to 255) : PWM period = 255 (n+1) / f(XIN) = 31.875 (n+1) s (when f(XIN) = 8 MHz) Output pulse "H" term = PWM period m / 255 = 0.125 (n+1) m s (when f(XIN) = 8 MHz)
31.875 m (n+1) s 255 PWM output T = [31.875 (n+1)] s m: Contents of PWM register n : Contents of PWM prescaler T : PWM period (when f(XIN) = 8 MHz
Fig. 45 Timing of PWM period
Data bus
PWM prescaler pre-latch
PWM register pre-latch
Transfer control circuit
PWM prescaler latch Count source selection bit XIN
or
PWM register latch
"0" "1"
Port P56 PWM register
PWM prescaler
XCIN 1/2
Port P56 latch
PWM enable bit
Fig. 46 Block diagram of PWM function
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-54
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
b7
b0
PWM control register (PWMCON : address 002B16) PWM function enable bit 0: PWM disabled 1: PWM enabled Count source selection bit 0: f(XIN) 1: f(XIN)/2 Not used (return "0" when read)
Fig. 47 Structure of PWM control register
A
B
C
B= C T2 T
PWM output T PWM register write signal T T2
(Changes "H" term from "A" to "B".)
PWM prescaler write signal
(Changes PWM period from "T" to "T2".)
When the contents of the PWM register or PWM prescaler have changed, the PWM output will change from the next period after the change.
Fig. 48 PWM output timing when PWM register or PWM prescaler is changed
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-55
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
A/D CONVERTER [AD Conversion Register 1, 2 (AD1, AD2)] 003516, 003816
The AD conversion register is a read-only register that stores the result of an A/D conversion. When reading this register during an A/D conversion, the previous conversion result is read. Bit 7 of the AD conversion register 2 is the conversion mode selection bit. When this bit is set to "0," the A/D converter becomes the 10-bit A/D mode. When this bit is set to "1," that becomes the 8-bit A/D mode. The conversion result of the 8-bit A/D mode is stored in the AD conversion register 1. As for 10-bit A/D mode, not only 10-bit reading but also only high-order 8-bit reading of conversion result can be performed by selecting the reading procedure of the AD conversion registers 1, 2 after A/D conversion is completed (in Figure 50). As for 10-bit A/D mode, the 8-bit reading inclined to MSB is performed when reading the AD converter register 1 after A/D conversion is started; and when the AD converter register 1 is read after reading the AD converter register 2, the 8-bit reading inclined to LSB is performed.
Channel Selector
The channel selector selects one of ports P67/AN7 to P60/AN0 or P07/AN15 to P00/AN8, and inputs the voltage to the comparator.
Comparator and Control Circuit
The comparator and control circuit compares an analog input voltage with the comparison voltage, and then stores the result in the AD conversion registers 1, 2. When an A/D conversion is completed, the control circuit sets the AD conversion completion bit and the AD interrupt request bit to "1". Note that because the comparator consists of a capacitor coupling, set f(XIN) to 500 kHz or more during an A/D conversion.
b7
b0
AD/DA control register (ADCON : address 003416) Analog input pin selection bits 1
b2 b1 b0
[AD/DA Control Register (ADCON)] 003416
The AD/DA control register controls the A/D conversion process. Bits 0 to 2 and bit 4 select a specific analog input pin. Bit 3 signals the completion of an A/D conversion. The value of this bit remains at "0" during an A/D conversion, and changes to "1" when an A/D conversion ends. Writing "0" to this bit starts the A/D conversion.
0 0 0 0 1 1 1 1
0 0 1 1 0 0 1 1
0: P60/AN0 or P00/AN8 1: P61/AN1 or P01/AN9 0: P62/AN2 or P02/AN10 1: P63/AN3 or P03/AN11 0: P64/AN4 or P04/AN12 1: P65/AN5 or P05/AN13 0: P66/AN6 or P06/AN14 1: P67/AN7 or P07/AN15
AD conversion completion bit 0: Conversion in progress 1: Conversion completed Analog input pin selection bit 2 0: AN0 to AN7 side 1: AN8 to AN15 side Not used (returns "0" when read) DA1 output enable bit 0: DA1 output disabled 1: DA1 output enabled DA2 output enable bit 0: DA2 output disabled 1: DA2 output enabled
Comparison Voltage Generator
The comparison voltage generator divides the voltage between VREF and AVSS into 1024, and that outputs the comparison voltage in the 10-bit A/D mode (256 division in 8-bit A/D mode). The A/D converter successively compares the comparison voltage Vref in each mode, dividing the VREF voltage (see below), with the input voltage. * 10-bit A/D mode (10-bit reading) Vref = VREF n (n = 0-1023) 1024 * 10-bit A/D mode (8-bit reading) Vref = VREF n (n = 0-255) 256 * 8-bit A/D mode Vref = VREF (n-0.5) (n = 1-255) 256 =0 (n = 0)
Fig. 49 Structure of AD/DA control register
10-bit reading
(Read address 003816 before 003516) b0 b7 AD conversion register 2 0 b9 b8 (AD2: address 003816) b7 b0 AD conversion register 1 b7 b6 b5 b4 b3 b2 b1 b0 (AD1: address 003516)
Note : Bits 2 to 6 of address 003816 become "0" at reading.
8-bit reading
(Read only address 003516) b7 b0 AD conversion register 1 b9 b8 b7 b6 b5 b4 b3 b2 (AD1: address 003516)
Fig. 50 Structure of 10-bit A/D mode reading
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-56
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
Data bus
AD/DA control register (Address 003416)
b7
b0
4 P60/AN0 P61/AN1 P62/AN2 P63/AN3 P64/AN4 P65/AN5 P66/AN6 P67/AN7 P00/AN8 P01/AN9 P02/AN10 P03/AN11 P04/AN12 P05/AN13 P06/AN14 P07/AN15 A/D control circuit AD conversion register 2 AD conversion register 1 10 Resistor ladder AD converter interrupt request
Comparator
(Address 003816) (Address 003516)
Channel selector
VREF AVSS
Fig. 51 Block diagram of A/D converter
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-57
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
D/A CONVERTER
The 3804 group (Spec. H) has two internal D/A converters (DA1 and DA2) with 8-bit resolution. The D/A conversion is performed by setting the value in each DA conversion register. The result of D/A conversion is output from the DA1 or DA2 pin by setting the DA output enable bit to "1". When using the D/A converter, the corresponding port direction register bit (P30/DA1 or P31/DA2) must be set to "0" (input status). The output analog voltage V is determined by the value n (decimal notation) in the DA conversion register as follows: V = VREF n/256 (n = 0 to 255) Where VREF is the reference voltage. At reset, the DA conversion registers are cleared to "0016", and the DA output enable bits are cleared to "0", and the P30/DA1 and P31/DA2 pins become high impedance. The DA output does not have buffers. Accordingly, connect an external buffer when driving a low-impedance load.
DA1 conversion register (8) DA1 output enable bit P30/DA1
Data bus
R-2R resistor ladder
DA2 conversion register (8) DA2 output enable bit P31/DA2
R-2R resistor ladder
Fig. 52 Block diagram of D/A converter
"0" DA1 output enable bit R P30/DA1 "1" MSB DA1 conversion register "0" "1" 2R
R
R
R
R
R
R
2R
2R
2R
2R
2R
2R
2R
2R LSB
AVSS VREF
Fig. 53 Equivalent connection circuit of D/A converter (DA1)
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-58
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
When bit 6 of the watchdog timer control register is kept at "0", the STP instruction is enabled. When that is executed, both the clock and the watchdog timer stop. Count re-starts at the same time as the release of stop mode (Note). The watchdog timer does not stop while a WIT instruction is executed. In addition, the STP instruction is disabled by writing "1" to this bit again. When the STP instruction is executed at this time, it is processed as an undefined instruction, and an internal reset occurs. Once a "1" is written to this bit, it cannot be programmed to "0" again. The following shows the period between the write execution to the watchdog timer control register and the underflow of watchdog timer H. Bit 7 of the watchdog timer control register is "0": when XCIN = 32.768 kHz; 32 s when XIN = 16 MHz; 65.536 ms Bit 7 of the watchdog timer control register is "1": when XCIN = 32.768 kHz; 125 ms when XIN = 16 MHz; 256 s
Note: The watchdog timer continues to count even while waiting for a stop release. Therefore, make sure that watchdog timer H does not underflow during this period.
WATCHDOG TIMER
The watchdog timer gives a mean of returning to the reset status when a program cannot run on a normal loop (for example, because of a software run-away). The watchdog timer consists of an 8-bit watchdog timer L and an 8-bit watchdog timer H.
Watchdog Timer Initial Value
Watchdog timer L is set to "FF16" and watchdog timer H is set to "FF16" by writing to the watchdog timer control register (address 001E16) or at a reset. Any write instruction that causes a write signal can be used, such as the STA, LDM, CLB, etc. Data can only be written to bits 6 and 7 of the watchdog timer control register. Regardless of the value written to bits 0 to 5, the above-mentioned value will be set to each timer.
Watchdog Timer Operations
The watchdog timer stops at reset and a countdown is started by the writing to the watchdog timer control register. An internal reset occurs when watchdog timer H underflows. The reset is released after its release time. After the release, the program is restarted from the reset vector address. Usually, write to the watchdog timer control register by software before an underflow of the watchdog timer H. The watchdog timer does not function if the watchdog timer control register is not written to at least once.
XCIN "10" Main clock division ratio selection bits (Note) XIN
"FF16" is set when watchdog timer control register is written to. Watchdog timer L (8) 1/16
Data bus "FF16" is set when watchdog timer control register is written to. Watchdog timer H (8)
"0" "1"
"00" "01"
Watchdog timer H count source selection bit
STP instruction disable bit STP instruction Reset circuit Reset release time waiting Note: Either high-speed, middle-speed or low-speed mode is selected by bits 7 and 6 of the CPU mode register. Internal reset
RESET
Fig. 54 Block diagram of Watchdog timer
b7
b0
Watchdog timer control register (WDTCON : address 001E16) Watchdog timer H (for read-out of high-order 6 bit) STP instruction disable bit 0: STP instruction enabled 1: STP instruction disabled Watchdog timer H count source selection bit 0: Watchdog timer L underflow 1: f(XIN)/16 or f(XCIN)/16
Fig. 55 Structure of Watchdog timer control register
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-59
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
MULTI-MASTER I2C-BUS INTERFACE
The 3804 group (Spec. H) has the multi-master interface. The multi-master I2C-BUS interface is a serial communications circuit, conforming to the Philips I2C-BUS data transfer format. This interface, offering both arbitration lost detection and a synchronous functions, is useful for the multi-master serial communications. Figure 56 shows a block diagram of the multi-master I2C-BUS interface and Table 7 lists the multi-master I 2 C-BUS interface functions. This multi-master I2C-BUS interface consists of the I2C slave address registers 0 to 2, the I2C data shift register, the I 2C clock control register, the I2C control register, the I2C status register, the I2C START/STOP condition control register, the I2C special mode control register, the I2C special mode status register, and other control circuits. When using the multi-master I2 C-BUS interface, set 1 MHz or more to the internal clock . I2C-BUS
Table 7 Multi-master I2C-BUS interface functions Item Function In conformity with Philips I2C-BUS standard: 10-bit addressing format 7-bit addressing format High-speed clock mode Standard clock mode In conformity with Philips I2C-BUS standard: Master transmission Master reception Slave transmission Slave reception 16.1 kHz to 400 kHz (at = 4 MHz)
Format
Communication mode
SCL clock frequency
System clock = f(XIN)/2 (high-speed mode) = f(XIN)/8 (middle-speed mode)
Interrupt generating circuit
Interrupt request signal (SCL, SDA, IRQ)
b7 I2C slave address registers 0 to 2 b0
SAD6 SAD5 SAD4 SAD3 SAD2 SAD1 SAD0 RWB
S0D0-2 Address comparator Serial data (SDA) Noise elimination circuit Data control circuit b7 I2C data shift register
S0
Interrupt generating circuit
Interrupt request signal (I2CIRQ)
b0 b7
MST TRX BB PIN
b0
AL AAS AD0 LRB
SIS SIP SSC4 SSC3 SSC2 SSC1 SSC0
S2D I2C START/STOP condition control register
AL circuit
S1
Internal data bus
I2C status register
BB circuit
Serial clock (SCL)
Noise elimination circuit
Clock control circuit
b7
ACK
b0
ACK FAST CCR4 CCR3 CCR2 CCR1 CCR0 BIT MODE
b7
S PCF PIN2
b0
A AS2 A AS1 A AS0
S2 I2C clock control register
Clock division
System clock ()
S3 I2C special mode status register
b7 b7
TISS TSEL 10BIT AL S SAD
b0
PIN2 HD PIN2 IN HSLAD ACK I CON
b0
ES0 BC2 BC1 BC0
SPCFL
S1D I2C control register
Bit counter
S3D I2 C special mode control register
Fig. 56 Block diagram of multi-master I2C-BUS interface
: Purchase of MITSUBISHI ELECTRIC CORPORATIONS I2C components conveys a license under the Philips I2C Patent Rights to use these components an I2C system, provided that the system conforms to the I2C Standard Specification as defined by Philips.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-60
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
[I2C Data Shift Register (S0)] 001116
The I2C data shift register (S0: address 001116) is an 8-bit shift register to store receive data and write transmit data. When transmit data is written into this register, it is transferred to the outside from bit 7 in synchronization with the SCL, and each time one-bit data is output, the data of this register are shifted by one bit to the left. When data is received, it is input to this register from bit 0 in synchronization with the SCL, and each time one-bit data is input, the data of this register are shifted by one bit to the left. The minimum 2 cycles of the internal clock are required from the rising of the SCL until input to this register. The I2C data shift register is in a write enable status only when the I2C-BUS interface enable bit (ES0 bit) of the I2C control register (S1D: address 001416) is "1". The bit counter is reset by a write instruction to the I2C data shift register. When both the ES0 bit and the MST bit of the I2C status register (S1: address 001316) are "1," the SCL is output by a write instruction to the I2C data shift register. Reading data from the I2C data shift register is always enabled regardless of the ES0 bit value.
b7
b0 I2C slave address register 0 (S0D0: address 0FF716) I2C slave address register 1 (S0D1: address 0FF816) I2C slave address register 2 (S0D2: address 0FF916) Read/write bit Slave address
SAD6 SAD5 SAD4 SAD3 SAD2 SAD1 SAD0 RWB
Fig. 57 Structure of I2C slave address registers 0 to 2
[I2C Slave Address Registers 0 to 2 (S0D0 to S0D2)] 0FF716 to 0FF916
The I2C slave address registers 0 to 2 (S0D0 to S0D2: addresses 0FF716 to 0FF916) consists of a 7-bit slave address and a read/ write bit. In the addressing mode, the slave address written in this register is compared with the address data to be received immediately after the START condition is detected. *Bit 0: Read/write bit (RWB) This is not used in the 7-bit addressing mode. In the 10-bit addressing mode, set RWB to "0" because the first address data to be received is compared with the contents (SAD6 to SAD0 + RWB) of the I2C slave address registers 0 to 2. When 2-byte address data match slave address, a 7-bit slave address which is received after restart condition has detected and R/W data can be matched by setting "1" to RWB with software. The RWB is cleared to "0" automatically when the stop condition is detected. *Bits 1 to 7: Slave address (SAD0-SAD6) These bits store slave addresses. Regardless of the 7-bit addressing mode or the 10-bit addressing mode, the address data transmitted from the master is compared with these bits' contents.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-61
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
[I2C Clock Control Register (S2)] 001516
The I2C clock control register (S2: address 001516) is used to set ACK control, SCL mode and SCL frequency. *Bits 0 to 4: SCL frequency control bits (CCR0-CCR4) These bits control the SCL frequency. Refer to Table 8. *Bit 5: SCL mode specification bit (FAST MODE) This bit specifies the SCL mode. When this bit is set to "0," the standard clock mode is selected. When the bit is set to "1," the high-speed clock mode is selected. When connecting the bus of the high-speed mode I2C bus standard (maximum 400 kbits/s), use 8 MHz or more oscillation frequency f(XIN) in the high-speed mode (2 division clock). *Bit 6: ACK bit (ACK BIT) This bit sets the SDA status when an ACK clock is generated. When this bit is set to "0," the ACK return mode is selected and SDA goes to "L" at the occurrence of an ACK clock. When the bit is set to "1," the ACK non-return mode is selected. The SDA is held in the "H" status at the occurrence of an ACK clock. However, when the slave address agree with the address data in the reception of address data at ACK BIT = "0," the SDA is automatically made "L" (ACK is returned). If there is a disagreement between the slave address and the address data, the SDA is automatically made "H" (ACK is not returned).
ACK clock: Clock for acknowledgment
b7
ACK ACK BIT
b0
FAST MODE CCR4 CCR3 CCR2 CCR1 CCR0
I2C clock control register (S2 : address 001516) SCL frequency control bits Refer to Table 8. SCL mode specification bit 0 : Standard clock mode 1 : High-speed clock mode ACK bit 0 : ACK is returned. 1 : ACK is not returned. ACK clock bit 0 : No ACK clock 1 : ACK clock
Fig. 58 Structure of I2C clock control register Table 8 Set values of I 2 C clock control register and SCL frequency SCL frequency Setting value of (at = 4 MHz, unit : kHz) (Note 1) CCR4-CCR0 Standard clock High-speed clock CCR4 CCR3 CCR2 CCR1 CCR0 mode mode 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 0 0 1 1 0 0 1 0 1 0 1 0 1 0 Setting disabled Setting disabled Setting disabled - (Note 2) - (Note 2) 100 83.3 500/CCR value (Note 3) 17.2 16.6 16.1 Setting disabled Setting disabled Setting disabled 333 250 400 (Note 3) 166 1000/CCR value (Note 3) 34.5 33.3 32.3
*Bit 7: ACK clock bit (ACK) This bit specifies the mode of acknowledgment which is an acknowledgment response of data transfer. When this bit is set to "0," the no ACK clock mode is selected. In this case, no ACK clock occurs after data transmission. When the bit is set to "1," the ACK clock mode is selected and the master generates an ACK clock each completion of each 1-byte data transfer. The device for transmitting address data and control data releases the SDA at the occurrence of an ACK clock (makes SDA "H") and receives the ACK bit generated by the data receiving device.
Note: Do not write data into the I2C clock control register during transfer. If data is written during transfer, the I 2C clock generator is reset, so that data cannot be transferred normally.
...
...
...
...
0 1 1
1 1 1
1 1 1
1 1 1
Notes 1: Duty of SCL output is 50 %. The duty becomes 35 to 45 % only when the high-speed clock mode is selected and CCR value = 5 (400 kHz, at = 4 MHz). "H" duration of the clock fluctuates from -4 to +2 machine cycles in the standard clock mode, and fluctuates from -2 to +2 machine cycles in the high-speed clock mode. In the case of negative fluctuation, the frequency does not increase because "L" duration is extended instead of "H" duration reduction. These are values when SCL synchronization by the synchronous function is not performed. CCR value is the decimal notation value of the SCL frequency control bits CCR4 to CCR0. 2: Each value of SCL frequency exceeds the limit at = 4 MHz or more. When using these setting value, use of 4 MHz or less. 3: The data formula of SCL frequency is described below: /(8 CCR value) Standard clock mode /(4 CCR value) High-speed clock mode (CCR value 5) /(2 CCR value) High-speed clock mode (CCR value = 5) Do not set 0 to 2 as CCR value regardless of frequency. Set 100 kHz (max.) in the standard clock mode and 400 kHz (max.) in the high-speed clock mode to the SCL frequency by setting the SCL frequency control bits CCR4 to CCR0.
...
1 0 1
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-62
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
[I2C Control Register (S1D)] 001416
The I2C control register (S1D: address 001416) controls data communication format. *Bits 0 to 2: Bit counter (BC0-BC2) These bits decide the number of bits for the next 1-byte data to be transmitted. The I2C interrupt request signal occurs immediately after the number of count specified with these bits (ACK clock is added to the number of count when ACK clock is selected by ACK clock bit (bit 7 of S2, address 001516) have been transferred, and BC0 to BC2 are returned to "0002". Also when a START condition is received, these bits become "0002" and the address data is always transmitted and received in 8 bits. *Bit 3: I2C interface enable bit (ES0) This bit enables to use the multi-master I2C-BUS interface. When this bit is set to "0," the use disable status is provided, so that the SDA and the SCL become high-impedance. When the bit is set to "1," use of the interface is enabled. When ES0 = "0," the following is performed. * PIN = "1," BB = "0" and AL = "0" are set (which are bits of the I2C status register, S1, at address 001316 ). * Writing data to the I2C data shift register (S0: address 001116) is disabled. *Bit 4: Data format selection bit (ALS) This bit decides whether or not to recognize slave addresses. When this bit is set to "0," the addressing format is selected, so that address data is recognized. When a match is found between a slave address and address data as a result of comparison or when a general call (refer to "I 2 C Status Register," bit 1) is received, transfer processing can be performed. When this bit is set to "1," the free data format is selected, so that slave addresses are not recognized. *Bit 5: Addressing format selection bit (10BIT SAD) This bit selects a slave address specification format. When this bit is set to "0," the 7-bit addressing format is selected. In this case, only the high-order 7 bits (slave address) of the I2C slave address registers 0 to 2 are compared with address data. When this bit is set to "1," the 10-bit addressing format is selected, and all the bits of the I2C slave address registers 0 to 2 are compared with address data. *Bit 7: I2C-BUS interface pin input level selection bit (TISS) This bit selects the input level of the SCL and SDA pins of the multi-master I2C-BUS interface.
b7
TISS
10 B IT S AD
b0
ALS ES0 BC2 BC1 BC0
I2C control register (S1D : address 001416) Bit counter (Number of transmit/receive bits) b2 b 1 b0 0 0 0:8 0 0 1:7 0 1 0:6 0 1 1:5 1 0 0:4 1 0 1:3 1 1 0:2 1 1 1:1 I2C-BUS interface enable bit 0 : Disabled 1 : Enabled Data format selection bit 0 : Addressing format 1 : Free data format Addressing format selection bit 0 : 7-bit addressing format 1 : 10-bit addressing format Not used (return "0" when read) I2C-BUS interface pin input level selection bit 0 : SMBUS input 1 : CMOS input
Fig. 59 Structure of I2C control register
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-63
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
[I2C Status Register (S1)] 001316
The I2C status register (S1: address 001316) controls the I2C-BUS interface status. The low-order 4 bits are read-only bits and the high-order 4 bits can be read out and written to. Set "00002" to the low-order 4 bits, because these bits become the reserved bits at writing. *Bit 0: Last receive bit (LRB) This bit stores the last bit value of received data and can also be used for ACK receive confirmation. If ACK is returned when an ACK clock occurs, the LRB bit is set to "0." If ACK is not returned, this bit is set to "1." Except in the ACK mode, the last bit value of received data is input. The state of this bit is changed from "1" to "0" by executing a write instruction to the I2C data shift register (S0: address 001116). *Bit 1: General call detecting flag (AD0) When the ALS bit is "0", this bit is set to "1" when a general call whose address data is all "0" is received in the slave mode. By a general call of the master device, every slave device receives control data after the general call. The AD0 bit is set to "0" by detecting the STOP condition or START condition, or reset.
General call: The master transmits the general call address "0016" to all slaves.
*Bit 2: Slave address comparison flag (AAS) This flag indicates a comparison result of address data when the ALS bit is "0". In the slave receive mode, when the 7-bit addressing format is selected, this bit is set to "1" in one of the following conditions: * The address data immediately after occurrence of a START condition agrees with the slave address stored in the high-order 7 bits of the I2C slave address register. * A general call is received. In the slave receive mode, when the 10-bit addressing format is selected, this bit is set to "1" with the following condition: * When the address data is compared with the I 2C slave address register (8 bits consisting of slave address and RWB bit), the first bytes agree. This bit is set to "0" by executing a write instruction to the I2C data shift register (S0: address 001116) when ES0 is set to "1" or reset. *Bit 3: Arbitration lost detecting flag (AL) In the master transmission mode, when the SDA is made "L" by any other device, arbitration is judged to have been lost, so that this bit is set to "1." At the same time, the TRX bit is set to "0," so that immediately after transmission of the byte whose arbitration was lost is completed, the MST bit is set to "0." The arbitration lost can be detected only in the master transmission mode. When arbitration is lost during slave address transmission, the TRX bit is set to "0" and the reception mode is set. Consequently, it becomes possible to detect the agreement of its own slave address and address data transmitted by another master device. The AL bit is set to "0" in one of the following conditions: *Executing a write instruction to the I2C data shift register (S0: address 001116) *When the ES0 bit is "0" *At reset
Arbitration lost :The status in which communication as a master is disabled.
*Bit 4: SCL pin low hold bit (PIN) This bit generates an interrupt request signal. Each time 1-byte data is transmitted, the PIN bit changes from "1" to "0." At the same time, an interrupt request signal occurs to the CPU. The PIN bit is set to "0" in synchronization with a falling of the last clock (including the ACK clock) of an internal clock and an interrupt request signal occurs in synchronization with a falling of the PIN bit. When the PIN bit is "0," the SCL is kept in the "0" state and clock generation is disabled. Figure 61 shows an interrupt request signal generating timing chart. The PIN bit is set to "1" in one of the following conditions: * Executing a write instruction to the I 2C data shift register (S0: address 001116). (This is the only condition which the prohibition of the internal clock is released and data can be communicated except for the start condition detection.) * When the ES0 bit is "0" * At reset * When writing "1" to the PIN bit by software The PIN bit is set to "0" in one of the following conditions: * Immediately after completion of 1-byte data transmission (including when arbitration lost is detected) * Immediately after completion of 1-byte data reception * In the slave reception mode, with ALS = "0" and immediately after completion of slave address agreement or general call address reception * In the slave reception mode, with ALS = "1" and immediately after completion of address data reception *Bit 5: Bus busy flag (BB) This bit indicates the status of use of the bus system. When this bit is set to "0," this bus system is not busy and a START condition can be generated. The BB flag is set/reset by the SCL, SDA pins input signal regardless of master/slave. This flag is set to "1" by detecting the START condition, and is set to "0" by detecting the STOP condition. The condition of these detecting is set by the START/STOP condition setting bits (SSC4-SSC0) of the I 2 C START/STOP condition control register (S2D: address 001616). When the ES0 bit of the I2C control register (bit 3 of S1D, address 001416) is "0" or reset, the BB flag is set to "0." For the writing function to the BB flag, refer to the sections "START Condition Generating Method" and "STOP Condition Generating Method" described later.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-64
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
*Bit 6: Communication mode specification bit (transfer direction specification bit: TRX) This bit decides a direction of transfer for data communication. When this bit is "0," the reception mode is selected and the data of a transmitting device is received. When the bit is "1," the transmission mode is selected and address data and control data are output onto the SDA in synchronization with the clock generated on the SCL. This bit is set/reset by software and hardware. About set/reset by hardware is described below. This bit is set to "1" by hardware when all the following conditions are satisfied: * When ALS is "0" * In the slave reception mode or the slave transmission mode * When the R/W bit reception is "1" This bit is set to "0" in one of the following conditions: * When arbitration lost is detected. * When a STOP condition is detected. * When writing "1" to this bit by software is invalid by the START condition duplication preventing function (Note). * With MST = "0" and when a START condition is detected. * With MST = "0" and when ACK non-return is detected. * At reset *Bit 7: Communication mode specification bit (master/slave specification bit: MST) This bit is used for master/slave specification for data communication. When this bit is "0," the slave is specified, so that a START condition and a STOP condition generated by the master are received, and data communication is performed in synchronization with the clock generated by the master. When this bit is "1," the master is specified and a START condition and a STOP condition are generated. Additionally, the clocks required for data communication are generated on the SCL. This bit is set to "0" in one of the following conditions. * Immediately after completion of the byte which has lost arbitration when arbitration lost is detected * When a STOP condition is detected. * Writing "1" to this bit by software is invalid by the START condition duplication preventing function (Note). * At reset
Note: START condition duplication preventing function The MST, TRX, and BB bits is set to "1" at the same time after confirming that the BB flag is "0" in the procedure of a START condition occurrence. However, when a START condition by another master device occurs and the BB flag is set to "1" immediately after the contents of the BB flag is confirmed, the START condition duplication preventing function makes the writing to the MST and TRX bits invalid. The duplication preventing function becomes valid from the rising of the BB flag to reception completion of slave address.
b7
b0 I2C status register (S1 : address 001316) Last receive bit (Note) 0 : Last bit = "0" 1 : Last bit = "1" General call detecting flag (Note) 0 : No general call detected 1 : General call detected Slave address comparison flag (Note) 0 : Address disagreement 1 : Address agreement Arbitration lost detecting flag (Note) 0 : Not detected 1 : Detected SCL pin low hold bit 0 : SCL pin low hold 1 : SCL pin low release Bus busy flag 0 : Bus free 1 : Bus busy Communication mode specification bits 00 : Slave receive mode 01 : Slave transmit mode 10 : Master receive mode 11 : Master transmit mode
MST TRX BB PIN AL AAS AD0 LRB
Note: These bits and flags can be read out, but cannot be written. Write "0" to these bits at writing.
Fig. 60 Structure of I2C status register
SCL PIN
I2CIRQ
Fig. 61 Interrupt request signal generating timing
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-65
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
START Condition Generating Method
When writing "1" to the MST, TRX, and BB bits of the I2C status register (S1: address 001316) at the same time after writing the slave address to the I2C data shift register (S0: address 001116) with the condition in which the ES0 bit of the I2C control register (S1D: address 001416) is "1" and the BB flag is "0", a START condition occurs. After that, the bit counter becomes "0002" and an SCL for 1 byte is output. The START condition generating timing is different in the standard clock mode and the high-speed clock mode. Refer to Figure 62, the START condition generating timing diagram, and Table 9, the START condition generating timing table.
STOP Condition Generating Method
When the ES0 bit of the I 2 C control register (S1D: address 001416) is "1," write "1" to the MST and TRX bits, and write "0" to the BB bit of the I2C status register (S1: address 001316) simultaneously. Then a STOP condition occurs. The STOP condition generating timing is different in the standard clock mode and the high-speed clock mode. Refer to Figure 63, the STOP condition generating timing diagram, and Table 10, the STOP condition generating timing table.
I2C status register write signal SCL Setup time Hold time
I 2C
status register write signal Setup time Hold time
SDA
SCL SDA
Fig. 63 STOP condition generating timing diagram Table 10 STOP condition generating timing table High-speed clock mode Standard clock mode Item 3.0 s (12 cycles) 5.0 s (20 cycles) Setup time 2.5 s (10 cycles) 4.5 s (18 cycles) Hold time
Note: Absolute time at = 4 MHz. The value in parentheses denotes the number of cycles.
Fig. 62 START condition generating timing diagram
Table 9 START condition generating timing table Standard clock mode High-speed clock mode Item 2.5 s (10 cycles) 5.0 s (20 cycles) Setup time 2.5 s (10 cycles) 5.0 s (20 cycles) Hold time
Note: Absolute time at = 4 MHz. The value in parentheses denotes the number of cycles.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-66
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
START/STOP Condition Detecting Operation
The START/STOP condition detection operations are shown in Figures 64, 65, and Table 11. The START/STOP condition is set by the START/STOP condition set bit. The START/STOP condition can be detected only when the input signal of the SCL and SDA pins satisfy three conditions: SCL release time, setup time, and hold time (see Table 11). The BB flag is set to "1" by detecting the START condition and is reset to "0" by detecting the STOP condition. The BB flag set/reset timing is different in the standard clock mode and the high-speed clock mode. Refer to Table 11, the BB flag set/ reset time.
Note: When a STOP condition is detected in the slave mode (MST = 0), an interrupt request signal "I2CIRQ" occurs to the CPU.
SCL release time SCL SDA BB flag Setup time Hold time
BB flag set time
Fig. 64 START/STOP condition detecting timing diagram
SCL release time SCL SDA BB flag Setup time Hold time
BB flag reset time
Table 11 START condition/STOP condition detecting conditions Standard clock mode High-speed clock mode SCL release time Setup time Hold time BB flag set/ reset time SSC value + 1 cycle (6.25 s) 4 cycles (1.0 s) SSC value + 1 cycle < 4.0 s (3.125 s) 2 cycles (0.5 s) 2 SSC value + 1 cycle < 4.0 s (3.125 s) 2 cycles (0.5 s) 2 SSC value -1 + 2 cycles (3.375 s) 3.5 cycles (0.875 s) 2
Fig. 65 STOP condition detecting timing diagram
Note: Unit : Cycle number of internal clock SSC value is the decimal notation value of the START/STOP condition set bits SSC4 to SSC0. Do not set "0" or an odd number to SSC value. The value in parentheses is an example when the I2C START/ STOP condition control register is set to "1816" at = 4 MHz.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-67
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
[I2C START/STOP Condition Control Register (S2D)] 001616
The I2C START/STOP condition control register (S2D: address 001616) controls START/STOP condition detection. *Bits 0 to 4: START/STOP condition set bits (SSC4-SSC0) SCL release time, setup time, and hold time change the detection condition by value of the main clock divide ratio selection bit and the oscillation frequency f(XIN) because these time are measured by the internal system clock. Accordingly, set the proper value to the START/STOP condition set bits (SSC4 to SSC0) in considered of the system clock frequency. Refer to Table 11. Do not set "000002" or an odd number to the START/STOP condition set bits (SSC4 to SSC0). Refer to Table 12, the recommended set value to START/STOP condition set bits (SSC4-SSC0) for each oscillation frequency. *Bit 5: SCL/SDA interrupt pin polarity selection bit (SIP) An interrupt can occur when detecting the falling or rising edge of the SCL or SDA pin. This bit selects the polarity of the SCL or SDA pin interrupt pin.
*Bit 6: SCL/SDA interrupt pin selection bit (SIS) This bit selects the pin of which interrupt becomes valid between the SCL pin and the SDA pin.
Note: When changing the setting of the SCL/SDA interrupt pin polarity selection bit, the SCL/SDA interrupt pin selection bit, or the I2C-BUS interface enable bit ES0, the SCL/SDA interrupt request bit may be set. When selecting the SCL/SDA interrupt source, disable the interrupt before the SCL/SDA interrupt pin polarity selection bit, the SCL/ SDA interrupt pin selection bit, or the I2C-BUS interface enable bit ES0 is set. Reset the request bit to "0" after setting these bits, and enable the interrupt.
b7
b0
SIS SIP SSC4 SSC3 SSC2 SSC1 SSC0
I2C START/STOP condition control register (S2D : address 001616) START/STOP condition set bits SCL/SDA interrupt pin polarity selection bit 0 : Falling edge active 1 : Rising edge active SCL/SDA interrupt pin selection bit 0 : SDA valid 1 : SCL valid Not used (Fix this bit to "0".)
Fig. 66 Structure of I2C START/STOP condition control register Table 12 Recommended set value to START/STOP condition set bits (SSC4-SSC0) for each oscillation frequency Oscillation frequency f(XIN) (MHz) 8 8 4 2 Main clock divide ratio 2 8 2 2 Internal clock (MHz) 4 1 2 1 START/STOP condition control register XXX11010 XXX11000 XXX00100 XXX01100 XXX01010 XXX00100 SCL release time (s) 6.75 s (27 cycles) 6.25 s (25 cycles) 5.0 s (5 cycles) 6.5 s (13 cycles) 5.5 s (11 cycles) 5.0 s (5 cycles) Setup time (s) 3.5 s (14 cycles) 3.25 s (13 cycles) 3.0 s (3 cycles) 3.5 s (7 cycles) 3.0 s (6 cycles) 3.0 s (3 cycles) Hold time (s) 3.25 s (13 cycles) 3.0 s (12 cycles) 2.0 s (2 cycles) 3.0 s (6 cycles) 2.5 s (5 cycles) 2.0 s (2 cycles)
Note: Do not set an odd number to the START/STOP condition set bits (SSC4 to SSC0) and "000002".
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-68
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
[I 2 C Special Mode Status Register (S3)] 001216
The I2 C special mode status register (S3: address 001216) consists of the flags indicating I2C operating state in the I2C special mode, which is set by the I2C special mode control register (S3D: address 001716). The stop condition flag is valid in all operating modes. *Bit 0: Slave address 0 comparison flag (AAS0) Bit 1: Slave address 1 comparison flag (AAS1) Bit 2: Slave address 2 comparison flag (AAS2) These flags indicate a comparison result of address data. These flags are valid only when the slave address control bit (MSLAD) is "1". In the 7-bit addressing format of the slave reception mode, the respective slave address i (i = 0, 1, 2) comparison flags corresponding to the I2C slave address registers 0 to 2 are set to "1" when an address data immediately after an occurrence of a START condition agrees with the high-order 7-bit slave address stored in the I2C slave address registers 0 to 2 (addresses 0FF716 to 0FF916). In the 10-bit addressing format of the slave mode, the respective slave address i (i = 0, 1, 2) comparison flags corresponding to the I2C slave address registers are set to "1" when an address data is compared with the 8 bits consisting of the slave address stored in the I2C slave address registers 0 to 2 and the RWB bit, and the first byte agrees. These flags are initialized to "0" at reset, when the slave address control bit (MSLAD) is "0", or when writing data to the I2C data shift register (S0: address 001116).
*Bit 5: SCL pin low hold 2 flag (PIN2) When the ACK interrupt control bit (ACKICON) and the ACK clock bit (ACK) are "1", this flag is set to "0" in synchronization with the falling of the data's last SCL clock, just before the ACK clock. The SCL pin is simultaneously held low, and the I2C interrupt request occurs. This flag is initialized to "1" at reset, when the ACK interrupt control bit (ACKICON) is "0", or when writing "1" to the SCL pin low hold 2 flag set bit (PIN2IN). The SCL pin is held low when either the SCL pin low hold bit (PIN) or the SCL pin low hold 2 flag (PIN2) becomes "0". The low hold state of the SCL pin is released when both the SCL pin low hold bit (PIN) and the SCL pin low hold 2 flag (PIN2) are "1". *Bit 7: Stop condition flag (SPCF) This flag is set to "1" when a STOP condition occurs. This flag is initialized to "0" at reset, when the I2C-BUS interface enable bit (ES0) is "0", or when writing "1" to the STOP condition flag clear bit (SPFCL).
b7
SP CF PIN2
b0
AAS2 AA S1 AAS0
I2C special mode status register (S3 : address 001216) Slave address 0 comparison flag 0 : Address disagreement 1 : Address agreement Slave address 1 comparison flag 0 : Address disagreement 1 : Address agreement Slave address 2 comparison flag 0 : Address disagreement 1 : Address agreement Not used (return "0" when read) Not used (return "0" when read) SCL pin low hold 2 flag 0 : SCL pin low hold 1 : SCL pin low release (Note) Not used (return "0" when read) STOP condition flag 0 : No detection 1 : Detection
Note: In order that the low hold state of the SCL pin may release, it is necessary that the SCL pin low hold 2 flag and the SCL pin low hold bit (PIN) are "1" simultaneously.
Fig. 67 Structure of I2C special mode status register
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-69
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
[I 2 C Special Mode Control Register (S3D)] 001716
The I2C special mode control register (S3D: address 001716) controls special functions such as occurrence timing of reception interrupt request and extending slave address comparison to 3 bytes. *Bit 1: ACK interrupt control bit (ACKICON) This bit controls the timing of I2C interrupt request occurrence at completion of data receiving due to master reception or slave reception. When this bit is "0", the SCL pin low hold bit (PIN) is set to "0" in synchronization with the falling of the last SCL clock, including the ACK clock. The SCL pin is simultaneously held low, and the I2C interrupt request occurs. When this bit is "1" and the ACK clock bit (ACK) is "1", the SCL pin low hold 2 flag (PIN2) is set to "0" in synchronization with the falling of the data's last SCL clock, just before the ACK clock. The SCL pin is simultaneously held low, and the I2C interrupt request occurs again. The ACK bit can be changed after the contents of data are confirmed by using this function.
*Bit 2: I2C slave address control bit (MSLAD) This bit controls a slave address. When this bit is "0", only the I2C slave address register 0 (address 0FF716) becomes valid as a slave address and a read/write bit. When this bit is "1", all of the I2C slave address registers 0 to 2 (addresses 0FF716 to 0FF916) become valid as a slave address and a read/write bit. In this case, when an address data agrees with any one of the I2C slave address registers 0 to 2, the slave address comparison flag (AAS) is set to "1" and the I2C slave address comparison flag corresponding to the agreed I 2C slave address registers 0 to 2 is also set to "1". *Bit 5: SCL pin low hold 2 flag set bit (PIN2IN) Writing "1" to this bit initializes the SCL pin low hold 2 flag (PIN2) to "1". When writing "0", nothing is generated. *Bit 6: SCL pin low hold set bit (PIN2HD) When the SCL pin low hold bit (PIN) becomes "0", the SCL pin is held low. However, the SCL pin low hold bit (PIN) cannot be set to "0" by software. The SCL pin low hold set bit (PIN2HD) is used to , hold the SCL pin in the low state by software. When writing "1" to this bit, the SCL pin low hold 2 flag (PIN2) becomes "0", and the SCL pin is held low. When writing "0", nothing occurs. *Bit 7: STOP condition flag clear bit (SPFCL) Writing "1" to this bit initializes the STOP condition flag (SPCF) to "0". When writing "0", nothing is generated.
b7
SPFCL
b0
PIN2- PIN2IN HD
MSLAD
ACKI CON
I2C special mode control register (S3D : address 001716) Not used (Fix this bit to "0".)
ACK interrupt control bit 0 : At communication completion 1 : At falling of ACK clock and communication completion Slave address control bit 0 : One-byte slave address compare mode 1 : Three-byte slave address compare mode Not used (return "0" when read) Not used (Fix this bit to "0".) SCL pin low hold 2 flag set bit (Notes 1, 2) Writing "1" to this bit initializes the SCL pin low hold 2 flag to "1". SCL pin low hold set bit (Notes 1, 2) When writing "1" to this bit, the SCL pin low hold 2 flag becomes "0" and the SCL pin is held low. STOP condition flag clear bit (Note 2) Writing "1" to this bit initializes the STOP condition flag to "0". Notes 1: Do not write "1" to these bits simultaneously. 2: return "0" when read
Fig. 68 Structure of I2C special mode control register
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-70
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
Address Data Communication
There are two address data communication formats, namely, 7-bit addressing format and 10-bit addressing format. The respective address communication formats are described below. 7-bit addressing format To adapt the 7-bit addressing format, set the 10BIT SAD bit of the I2C control register (S1D: address 001416) to "0". The first 7bit address data transmitted from the master is compared with the high-order 7-bit slave address stored in the I 2C slave address register. At the time of this comparison, address comparison of the RWB bit of the I2C slave address register is not performed. For the data transmission format when the 7-bit addressing format is selected, refer to Figure 69, (1) and (2). 10-bit addressing format To adapt the 10-bit addressing format, set the 10BIT SAD bit of the I2C control register (S1D: address 001416) to "1." An address comparison is performed between the first-byte address data transmitted from the master and the 8-bit slave address stored in the I2C slave address register. At the time of this com-
parison, an address comparison between the RWB bit of the I2C slave address register and the R/W bit which is the last bit of the address data transmitted from the master is made. In the 10-bit addressing mode, the RWB bit which is the last bit of the address data not only specifies the direction of communication for control data, but also is processed as an address data bit. When the first-byte address data agree with the slave address, the AAS bit of the I2C status register (S1: address 001316) is set to "1." After the second-byte address data is stored into the I2C data shift register (S0: address 001116), perform an address comparison between the second-byte data and the slave address by software. When the address data of the 2 bytes agree with the slave address, set the RWB bit of the I2C slave address register to "1" by software. This processing can make the 7-bit slave address and R/W data agree, which are received after a RESTART condition is detected, with the value of the I2C slave address register. For the data transmission format when the 10-bit addressing format is selected, refer to Figure 69, (3) and (4).
(1) A master-transmitter transmits data to a slave-receiver S Slave address R/W 7 bits "0" A Data 1 to 8 bits A Data 1 to 8 bits A/A P
(2) A master-receiver receives data from a slave-transmitter S Slave address R/W 7 bits "1" A Data 1 to 8 bits A Data 1 to 8 bits A P
(3) A master-transmitter transmits data to a slave-receiver with a 10-bit address S Slave address R/W 1st 7 bits 7 bits "0" A Slave address 2nd bytes 8 bits A Data 1 to 8 bits A Data 1 to 8 bits A/A P
(4) A master-receiver receives data from a slave-transmitter with a 10-bit address S Slave address R/W 1st 7 bits 7 bits "0" A Slave address 2nd bytes 8 bits A Sr Slave address R/W 1st 7 bits 7 bits "1" A Data 1 to 8 bits A Data 1 to 8 bits A P
S : START condition A : ACK bit Sr : Restart condition
P : STOP condition R/W : Read/Write bit
: Master to slave : Slave to master
Fig. 69 Address data communication format
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-71
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
Example of Master Transmission
An example of master transmission in the standard clock mode, at the SCL frequency of 100 kHz and in the ACK return mode is shown below. Set a slave address in the high-order 7 bits of the I2C slave address register and "0" into the RWB bit. Set the ACK return mode and SCL = 100 kHz by setting "8516" in the I2C clock control register (S2: address 001516). Set "0016" in the I 2C status register (S1: address 001316) so that transmission/reception mode can become initializing condition. Set a communication enable status by setting "0816" in the I2C control register (S1D: address 001416). Confirm the bus free condition by the BB flag of the I2C status register (S1: address 001316). Set the address data of the destination of transmission in the high-order 7 bits of the I 2 C data shift register (S0: address 001116) and set "0" in the least significant bit. Set "F016" in the I 2C status register (S1: address 001316) to generate a START condition. At this time, an SCL for 1 byte and an ACK clock automatically occur. Set transmit data in the I 2 C data shift register (S0: address 001116). At this time, an SCL and an ACK clock automatically occur. When transmitting control data of more than 1 byte, repeat step . Set "D016" in the I2C status register (S1: address 001316) to generate a STOP condition if ACK is not returned from slave reception side or transmission ends.
Example of Slave Reception
An example of slave reception in the high-speed clock mode, at the SCL frequency of 400 kHz, in the ACK non-return mode and using the addressing format is shown below. Set a slave address in the high-order 7 bits of the I2C slave address register and "0" in the RWB bit. Set the no ACK clock mode and SCL = 400 kHz by setting "2516" in the I2C clock control register (S2: address 001516). Set "0016" in the I2C status register (S1: address 001316) so that transmission/reception mode can become initializing condition. Set a communication enable status by setting "0816" in the I2C control register (S1D: address 001416). When a START condition is received, an address comparison is performed. *When all transmitted addresses are "0" (general call): AD0 of the I2C status register (S1: address 001316) is set to "1" and an interrupt request signal occurs. * When the transmitted addresses agree with the address set in : AAS of the I2C status register (S1: address 001316) is set to "1" and an interrupt request signal occurs. * In the cases other than the above AD0 and AAS of the I2C status register (S1: address 001316) are set to "0" and no interrupt request signal occurs. Set dummy data in the I 2 C data shift register (S0: address 001116). When receiving control data of more than 1 byte, repeat step . When a STOP condition is detected, the communication ends.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-72
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
sPrecautions when using multi-master I2CBUS interface
(1) Read-modify-write instruction The precautions when the read-modify-write instruction such as SEB, CLB etc. is executed for each register of the multi-master I2C-BUS interface are described below. * I2C data shift register (S0: address 001116) When executing the read-modify-write instruction for this register during transfer, data may become a value not intended. * I2C slave address registers 0 to 2 (S0D0 to S0D2: addresses 0FF716 to0FF916) When the read-modify-write instruction is executed for this register at detecting the STOP condition, data may become a value not intended. It is because H/W changes the read/write bit (RWB) at the above timing. * I2C status register (S1: address 001316) Do not execute the read-modify-write instruction for this register because all bits of this register are changed by H/W. * I2C control register (S1D: address 001416) When the read-modify-write instruction is executed for this register at detecting the START condition or at completing the byte transfer, data may become a value not intended. Because H/W changes the bit counter (BC0-BC2) at the above timing. * I2C clock control register (S2: address 001516) The read-modify-write instruction can be executed for this register. * I 2 C START/STOP condition control register (S2D: address 001616) The read-modify-write instruction can be executed for this register. (2) START condition generating procedure using multi-master 1. Procedure example (The necessary conditions of the generating procedure are described as the following 2 to 5. : : LDA -- SEI BBS 5, S1, BUSBUSY BUSFREE: STA S0 LDM #$F0, S1 CLI : : BUSBUSY: CLI : : (Taking out of slave address value) (Interrupt disabled) (BB flag confirming and branch process) (Writing of slave address value) (Trigger of START condition generating) (Interrupt enabled)
5. Disable interrupts during the following three process steps: * BB flag confirming * Writing of slave address value * Trigger of START condition generating When the condition of the BB flag is bus busy, enable interrupts immediately. (3) RESTART condition generating procedure 1. Procedure example (The necessary conditions of the generating procedure are described as the following 2 to 4.) Execute the following procedure when the PIN bit is "0." : : LDM #$00, S1 LDA -- SEI STA S0 LDM #$F0, S1 CLI : : (Select slave receive mode) (Taking out of slave address value) (Interrupt disabled) (Writing of slave address value) (Trigger of RESTART condition generating) (Interrupt enabled)
2. Select the slave receive mode when the PIN bit is "0." Do not write "1" to the PIN bit. Neither "0" nor "1" is specified for the writing to the BB bit. The TRX bit becomes "0" and the SDA pin is released. 3. The SCL pin is released by writing the slave address value to the I2C data shift register. 4. Disable interrupts during the following two process steps: * Writing of slave address value * Trigger of RESTART condition generating (4) Writing to I2C status register Do not execute an instruction to set the PIN bit to "1" from "0" and an instruction to set the MST and TRX bits to "0" from "1" simultaneously. It is because it may enter the state that the SCL pin is released and the SDA pin is released after about one machine cycle. Do not execute an instruction to set the MST and TRX bits to "0" from "1" simultaneously when the PIN bit is "1." It is because it may become the same as above. (5) Process of after STOP condition generating Do not write data in the I2C data shift register S0 and the I2C status register S1 until the bus busy flag BB becomes "0" after generating the STOP condition in the master mode. It is because the STOP condition waveform might not be normally generated. Reading to the above registers does not have the problem.
(Interrupt enabled)
2. Use "Branch on Bit Set" of "BBS 5, S1, -" for the BB flag confirming and branch process. 3. Use "STA $12, STX $12" or "STY $12" of the zero page addressing instruction for writing the slave address value to the I2C data shift register. 4. Execute the branch instruction of above 2 and the store instruction of above 3 continuously shown the above procedure example.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-73
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
RESET CIRCUIT
To reset the microcomputer, RESET pin should be held at an "L" level for 16 cycles or more of XIN. Then the RESET pin is returned to an "H" level (the power source voltage should be between 2.7 V to 5.5 V, and the oscillation should be stable), reset is released. After the reset is completed, the program starts from the address contained in address FFFD16 (high-order byte) and address FFFC16 (low-order byte). Input to the RESET pin in the following procedure. qWhen power source is stabilized (1) Input "L" level to RESET pin. (2) Input "L" level for 16 cycles or more to XIN pin. (3) Input "H" level to RESET pin. qAt power-on (1) Input "L" level to RESET pin. (2) Increase the power source voltage to 2.7 V. (3) Wait for td(P-R) until internal power source has stabilized. (4) Input "L" level for 16 cycles or more to XIN pin. (5) Input "H" level to RESET pin.
VCC RESET VCC
0V
2.7 V
RESET
0V
0.2VCC or less td(P-R)+XIN 16 cycles or more
5V
RESET
VCC
Power source voltage detection circuit
VCC
0V 5V
2.7 V
RESET
0V
td(P-R)+XIN 16 cycles or more
Example at VCC = 5V
Fig. 70 Reset circuit example
XIN
RESET Internal reset
Address
?
?
?
?
FFFC
FFFD
ADH,L
Reset address from the vector table.
Data
?
?
?
?
ADL
ADH
SYNC
XIN: 10.5 to 18.5 clock cycles Notes 1: The frequency relation of f(XIN) and f() is f(XIN)=8 * f(). 2: The question marks (?) indicate an undefined state that depends on the previous state.
Fig. 71 Reset sequence
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-74
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
Address Register contents (1) (2) (3) (4) (5) (6) (7) (8) (9) Port P0 (P0) Port P0 direction register (P0D) Port P1 (P1) Port P1 direction register (P1D) Port P2 (P2) Port P2 direction register (P2D) Port P3 (P3) Port P3 direction register (P3D) Port P4 (P4) 000016 000116 000216 000316 000416 000516 000616 000716 000816 000916 000A16 000B16 000C16 000D16 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 (41) Timer Z (low-order) (TZL) (42) Timer Z (high-order) (TZH) (43) Timer Z mode register (TZM) (44) PWM control register (PWMCON) (45) PWM prescaler (PREPWM) (46) PWM register (PWM) (47) Baud rate generator 3 (BRG3) (48) Transmit/Receive buffer register 3 (TB3/RB3) (49) Serial I/O3 status register (SIO3STS) (50) Serial I/O3 control register (SIO3CON) (51) UART3 control register (UART3CON) (52) AD/DA control register (ADCON) (53) AD conversion register 1 (AD1) (54) DA1 conversion register (DA1) (55) DA2 conversion register (DA2) (56) AD conversion register 2 (AD2) (57) Interrupt source selection register (INTSEL) (58) Interrupt edge selection register (INTEDGE) (59) CPU mode register (CPUM) (60) Interrupt request register 1 (IREQ1) (61) Interrupt request register 2 (IREQ2) (62) Interrupt control register 1 (ICON1) (63) Interrupt control register 2 (ICON2) (64) Flash memory control register 0 (FMCR0) (65) Flash memory control register 1 (FMCR1) (66) Flash memory control register 2 (FMCR2) (67) Port P0 pull-up control register (PULL0) (68) Port P1 pull-up control register (PULL1) (69) Port P2 pull-up control register (PULL2) (70) Port P3 pull-up control register (PULL3) (71) Port P4 pull-up control register (PULL4) (72) Port P5 pull-up control register (PULL5) (73) Port P6 pull-up control register (PULL6) (74) I2C (75) I2C (76) I2C slave address register 0 (S0D0) slave address register 1 (S0D1) slave address register 2 (S0D3)
Address Register contents 002816 002916 002A16 002B16 FF16 FF16 0016 0016
002C16 X X X X X X X X 002D16 X X X X X X X X 002F16 X X X X X X X X 003016 X X X X X X X X 003116 1 0 0 0 0 0 0 0 003216 0016
(10) Port P4 direction register (P4D) (11) Port P5 (P5) (12) Port P5 direction register (P5D) (13) Port P6 (P6) (14) Port P6 direction register (P6D) (15) (16)
Timer 12, X count source selection register (T12XCSS) Timer Y, Z count source selection register (TYZCSS)
003316 1 1 1 0 0 0 0 0 003416 0 0 0 0 1 0 0 0 003516 X X X X X X X X 003616 003716 0016 0016
000E16 0 0 1 1 0 0 1 1 000F16 0 0 1 1 0 0 1 1 001016 0016
003816 0 0 0 0 0 0 X X 003916 003A16 0016 0016
(17) MISRG (18) I2C data shift register (S0) (19) I2C special mode status register (S3) (20) I2C status register (S1) (21) I2C control register (S1D) (22) I2C clock control register (S2)
001116 X X X X X X X X 001216 0 0 1 0 0 0 0 0 001316 0 0 0 1 0 0 0 X 001416 001516 0016 0016
003B16 0 1 0 0 1 0 0 0 003C16 003D16 003E16 003F16 0FE016 0FE116 0FE216 0FF016 0FF116 0FF216 0FF316 0FF416 0FF516 0FF616 0FF716 0FF816 0FF916 (PS) (PCH) (PCL) 0016 0016 0016 0016 0116 4016 4516 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 X XXXX1 XX
FFFD16 contents FFFC16 contents
(23) I2C START/STOP condition control register (S2D)001616 0 0 0 1 1 0 1 0 (24) I2C special mode control register (S3D) (25) Transmit/Receive buffer register 1 (TB1/RB1) (26) Serial I/O1 status register (SIO1STS) (27) Serial I/O1 control register (SIO1CON) (28) UART1 control register (UART1CON) (29) Baud rate generator 1 (BRG1) (30) Serial I/O2 control register (SIO2CON) (31) Watchdog timer control register (WDTCON) (32) Serial I/O2 register (SIO2) (33) Prescaler 12 (PRE12) (34) Timer 1 (T1) (35) Timer 2 (T2) (36) Timer XY mode register (TM) (37) Prescaler X (PREX) (38) Timer X (TX) (39) Prescaler Y (PREY) (40) Timer Y (TY) 001716 0016
001816 X X X X X X X X 001916 1 0 0 0 0 0 0 0 001A16 0016
001B16 1 1 1 0 0 0 0 0 001C16 X X X X X X X X 001D16 0016
001E16 0 0 1 1 1 1 1 1 001F16 X X X X X X X X 002016 002116 002216 002316 002416 002516 002616 002716 FF16 0116 FF16 0016 FF16 FF16 FF16 FF16
(77) Processor status register (78) Program counter
Note : X : Not fixed Since the initial values for other than above mentioned registers and RAM contents are indefinite at reset, they must be set.
Fig. 72 Internal status at reset
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-75
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
CLOCK GENERATING CIRCUIT
The 3804 group (Spec. H) has two built-in oscillation circuits: main clock XIN-XOUT oscillation circuit and sub clock XCIN-XCOUT oscillation circuit. An oscillation circuit can be formed by connecting a resonator between XIN and XOUT (XCIN and XCOUT). Use the circuit constants in accordance with the resonator manufacturer's recommended values. No external resistor is needed between XIN and XOUT since a feed-back resistor exists on-chip.(An external feed-back resistor may be needed depending on conditions.) However, an external feed-back resistor is needed between XCIN and XCOUT. Immediately after power on, only the XIN oscillation circuit starts oscillating, and XCIN and XCOUT pins function as I/O ports.
Oscillation Control (1) Stop mode
If the STP instruction is executed, the internal clock stops at an "H" level, and XIN and XCIN oscillators stop. When the oscillation stabilizing time set after STP instruction released bit is "0," the prescaler 12 is set to "FF16" and timer 1 is set to "0116." When the oscillation stabilizing time set after STP instruction released bit is "1," set the sufficient time for oscillation of used oscillator to stabilize since nothing is set to the prescaler 12 and timer 1. After STP instruction is released, the input of the prescaler 12 is connected to count source which had set at executing the STP instruction, and the output of the prescaler 12 is connected to timer 1. Set the timer 1 interrupt enable bit to disabled ("0") before executing the STP instruction. Oscillator restarts when an external interrupt is received, but the internal clock is not supplied to the CPU (remains at "H") until timer 1 underflows. The internal clock is supplied for the first time, when timer 1 underflows. Therefore make sure not to set the timer 1 interrupt request bit to "1" before the STP instruction stops the oscillator. When the oscillator is restarted by reset, apply "L" level to the RESET pin until the oscillation is stable since a wait time will not be generated. The internal power supply circuit is changed to low power consumption mode for consumption current reduction at the time of STP instruction execution. Although an internal power supply circuit is usually changed to the normal operation mode at the time of the return from an STP instruction, since a certain time is required to start the power supply to the flash memory and operation of flash memory to be enabled, set wait time 100 s or more by the oscillation stabilization time set function after release of the STP instruction which used the timer 1.
Frequency Control (1) Middle-speed mode
The internal clock is the frequency of XIN divided by 8. After reset is released, this mode is selected.
(2) High-speed mode
The internal clock is half the frequency of XIN.
(3) Low-speed mode
The internal clock is half the frequency of XCIN.
(4) Low power dissipation mode
The low power consumption operation can be realized by stopping the main clock XIN in low-speed mode. To stop the main clock, set bit 5 of the CPU mode register to "1." When the main clock XIN is restarted (by setting the main clock stop bit to "0"), set sufficient time for oscillation to stabilize.
(2) Wait mode
If the WIT instruction is executed, the internal clock stops at an "H" level, but the oscillator does not stop. The internal clock restarts when an interrupt is received. Since the oscillator does not stop, normal operation can be started immediately after the clock is restarted. sNote *If you switch the mode between middle/high-speed and lowspeed, stabilize both XIN and XCIN oscillations. The sufficient time is required for the sub clock to stabilize, especially immediately after power on and at returning from stop mode. When switching the mode between middle/high-speed and low-speed, set the frequency on condition that f(XIN) > 3f(XCIN). *When using the quartz-crystal oscillator of high frequency, such as 16 MHz etc., it may be necessary to select a specific oscillator with the specification demanded.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-76
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
XCIN Rf
XCOUT Rd CCOUT
XIN
XOUT
Rd (Note)
CCIN
CIN
COUT
Notes : Insert a damping resistor if required. The resistance will vary depending on the oscillator and the oscillation drive capacity setting. Use the value recommended by the maker of the oscillator. Also, if the oscillator manufacturer's data sheet specifies that a feedback resistor be added external to the chip though a feedback resistor exists on-chip, insert a feedback resistor between XIN and XOUT following the instruction. Fig. 73 Ceramic resonator circuit
XCIN
XCOUT Open
XIN
XOUT Open
External oscillation circuit VCC VSS
External oscillation circuit VCC VSS
Fig. 74 External clock input circuit
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-77
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
XCIN
XCOUT
"1"
"0"
Port XC switch bit
XIN
(Note 4)
XOUT
Main clock division ratio selection bits (Note 1) Low-speed mode
Divider Prescaler 12
(Note 3)
1/2
High-speed or middle-speed mode
1/4
Timer 1
Reset or STP instruction (Note 2)
Main clock division ratio selection bits (Note 1) Middle-speed mode High-speed or low-speed mode Main clock stop bit
Timing (internal clock)
Q
S R
STP instruction WIT instruction
SQ R
QS R
STP instruction
Reset
Reset Interrupt disable flag l Interrupt request
Notes 1: Either high-speed, middle-speed or low-speed mode is selected by bits 7 and 6 of the CPU mode register. When low-speed mode is selected, set port Xc switch bit (b4) to "1". 2: f(XIN)/16 is supplied as the count source to the prescaler 12 at reset. The count source before executing the STP instruction is supplied as the count source at executing STP instruction. 3: When bit 0 of MISRG is "0", timer 1 is set "0116" and prescaler 12 is set "FF16" automatically. When bit 0 of MISRG is "1", set the appropriate value to them in accordance with oscillation stablizing time required by the using oscillator because nothing is automatically set into timer 1 and prescaler 12. 4: Although a feed-back resistor exists on-chip, an external feed-back resistor may be needed depending on conditions.
Fig. 75 System clock generating circuit block diagram
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-78
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
Reset
Middle-speed mode (f()=1 MHz) CM7=0 CM6=1 CM5=0(8 MHz oscillating) CM4=0(32 kHz stopped)
CM6 "1""0"
High-speed mode (f()=4 MHz) CM7=0 CM6=0 CM5=0(8 MHz oscillating) CM4=0(32 kHz stopped)
CM " 0" "1 M6 " C " "1
4
" "0
C "0 M4 CM " "1 6 " 1" " "0 "
CM4 "1""0"
Middle-speed mode (f()=1 MHz) CM7=0 CM6=1 CM5=0(8 MHz oscillating) CM4=1(32 kHz oscillating)
CM6 "1""0"
High-speed mode (f()=4 MHz) CM7=0 CM6=0 CM5=0(8 MHz oscillating) CM4=1(32 kHz oscillating)
CM7=1 CM6=0 CM5=0(8 MHz oscillating) CM4=1(32 kHz oscillating)
CM7 "1""0"
Low-speed mode (f()=16 kHz)
C "0 M7 CM " "1 6 "1 " " "0 "
CM4 "1""0"
b7
b4 CPU mode register (CPUM : address 003B16)
CM4 : Port Xc switch bit 0 : I/O port function (stop oscillating) 1 : XCIN-XCOUT oscillating function CM5 : Main clock (XIN- XOUT) stop bit 0 : Operating 1 : Stopped CM7, CM6: Main clock division ratio selection bit b7 b6 0 0 : = f(XIN)/2 ( High-speed mode) 0 1 : = f(XIN)/8 (Middle-speed mode) 1 0 : = f(XCIN)/2 (Low-speed mode) 1 1 : Not available
CM7=1 CM6=0 CM5=1(8 MHz stopped) CM4=1(32 kHz oscillating)
Notes 1 : Switch the mode by the allows shown between the mode blocks. (Do not switch between the modes directly without an allow.) 2 : The all modes can be switched to the stop mode or the wait mode and return to the source mode when the stop mode or the wait mode is ended. 3 : Timer operates in the wait mode. 4 : When the stop mode is ended, a delay of approximately 1 ms occurs by connecting prescaler 12 and Timer 1 in middle/high-speed mode. 5 : When the stop mode is ended, a delay of approximately 0.25 s occurs by Timer 1 and Timer 2 in low-speed mode. 6 : Wait until oscillation stabilizes after oscillating the main clock XIN before the switching from the low-speed mode to middle/high-speed mode. 7 : The example assumes that 8 MHz is being applied to the XIN pin and 32 kHz to the XCIN pin. indicates the internal clock.
Fig. 76 State transitions of system clock
CM5 "1""0"
Low-speed mode (f()=16 kHz)
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-79
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
FLASH MEMORY MODE
The 3804 group (spec. H) has the flash memory that can be rewritten with a single power source. For this flash memory, three flash memory modes are available in which to read, program, and erase: the parallel I/O and standard serial I/O modes in which the flash memory can be manipulated using a programmer and the CPU rewrite mode in which the flash memory can be manipulated by the Central Processing Unit (CPU). This flash memory has some blocks on it as shown in Figure 77 and each block can be erased. In addition to the ordinary User ROM area to store the MCU operation control program, the flash memory has a Boot ROM area that is used to store a program to control rewriting in CPU rewrite and standard serial I/O modes. This Boot ROM area has had a standard serial I/O mode control program stored in it when shipped from the factory. However, the user can write a rewrite control program in this area that suits the user's application system. This Boot ROM area can be rewritten in only parallel I/O mode.
q Summary
Table 13 lists the summary of the 3804 Group (spec. H).
Table 13 Summary of 3804 group (spec. H) Item Power source voltage (Vcc) Program/Erase VPP voltage (VPP) Flash memory mode Erase block division User ROM area/Data ROM area Boot ROM area (Note) Program method Erase method Program/Erase control method Number of commands Number of program/Erase times ROM code protection Specifications VCC = 2.7 to 5.5 V VCC = 2.7 to 5.5 V 3 modes; Parallel I/O mode, Standard serial I/O mode, CPU rewrite mode Refer to Fig. 77. Not divided (4K bytes) In units of bytes Block erase Program/Erase control by software command 5 commands 100 Available in parallel I/O mode and standard serial I/O mode
Note: The Boot ROM area has had a standard serial I/O mode control program stored in it when shipped from the factory. This Boot ROM area can be erased and written in only parallel I/O mode.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-80
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
q Boot Mode
The control program for CPU rewrite mode must be written into the User ROM or Boot ROM area in parallel I/O mode beforehand. (If the control program is written into the Boot ROM area, the standard serial I/O mode becomes unusable.) See Figure 77 for details about the Boot ROM area. Normal microcomputer mode is entered when the microcomputer is reset with pulling CNVSS pin low. In this case, the CPU starts operating using the control program in the User ROM area. When the microcomputer is reset and the CNVSS pin high after pulling the P45/TxD1 pin and CNVss pin high, the CPU starts operating (start address of program is stored into addresses FFFC16 and FFFD16) using the control program in the Boot ROM area. This mode is called the "Boot mode". Also, User ROM area can be rewritten using the control program in the Boot ROM area.
q CPU Rewrite Mode
In CPU rewrite mode, the internal flash memory can be operated on (read, program, or erase) under control of the Central Processing Unit (CPU). In CPU rewrite mode, only the User ROM area shown in Figure 77 can be rewritten; the Boot ROM area cannot be rewritten. Make sure the program and block erase commands are issued for only the User ROM area and each block area. The control program for CPU rewrite mode can be stored in either User ROM or Boot ROM area. In the CPU rewrite mode, because the flash memory cannot be read from the CPU, the rewrite control program must be transferred to internal RAM area before it can be executed.
q Block Address
Block addresses refer to the maximum address of each block. These addresses are used in the block erase command.
000016 SFR area 004016 RAM 083F16 Internal RAM area (2K bytes) 100016 180016 200016
User ROM area Data block B: 2K bytes Data block A: 2K bytes
Block 3: 24K bytes Notes 1: The boot ROM area can be rewritten in a parallel I/O mode. (Access to except boot ROM area is disablrd.) 2: To specify a block, use the maximum address in the block.
0FE016 0FFF16 100016 SFR area
800016
Block 2: 16K bytes C00016 Block 1: 8 K bytes
Internal flash memory area (60K bytes)
E00016 Block 0: 8 K bytes
F00016 Boot ROM area 4K bytes FFFF16
FFFF16
FFFF16
Fig. 77 Block diagram of built-in flash memory
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-81
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
b7 b0 Flash memory control register 0 (FMCR0: address : 0FE016: initial value: 0116) RY/BY status flag
qOutline Performance
CPU rewrite mode is usable in the single-chip or Boot mode. The only User ROM area can be rewritten. In CPU rewrite mode, the CPU erases, programs and reads the internal flash memory as instructed by software commands. This rewrite control program must be transferred to internal RAM area before it can be executed. The MCU enters CPU rewrite mode by setting "1" to the CPU rewrite mode select bit (bit 1 of address 0FE016). Then, software commands can be accepted. Use software commands to control program and erase operations. Whether a program or erase operation has terminated normally or in error can be verified by reading the status register. Figure 78 shows the flash memory control register 0. Bit 0 of the flash memory control register 0 is the RY/BY status flag used exclusively to read the operating status of the flash memory. During programming and erase operations, it is "0" (busy). Otherwise, it is "1" (ready). Bit 1 of the flash memory control register 0 is the CPU rewrite mode select bit. When this bit is set to "1", the MCU enters CPU rewrite mode. And then, software commands can be accepted. In CPU rewrite mode, the CPU becomes unable to access the internal flash memory directly. Therefore, use the control program in the internal RAM for write to bit 1. To set this bit 1 to "1", it is necessary to write "0" and then write "1" in succession to bit 1. The bit can be set to "0" by only writing "0". Bit 2 of the flash memory control register 0 is the 8 KB user block E/W enable bit. By setting combination of bit 4 of the flash memory control register 2 and this bit as shown in Table 14, E/W is disabled to user block in the CPU rewriting mode. Bit 3 of the flash memory control register 0 is the flash memory reset bit used to reset the control circuit of internal flash memory. This bit is used when flash memory access has failed. When the CPU rewrite mode select bit is "1", setting "1" for this bit resets the control circuit. To release the reset, it is necessary to set this bit to "0". Bit 5 of the flash memory control register 0 is the User ROM area select bit and is valid only in the boot mode. Setting this bit to "1" in the boot mode switches an accessible area from the boot ROM area to the user ROM area. To use the CPU rewrite mode in the boot mode, set this bit to "1". To rewrite bit 5, execute the useroriginal reprogramming control software transferred to the internal RAM in advance. Bit 6 of the flash memory control register 0 is the program status flag. This bit is set to "1" when writing to flash memory is failed. When program error occurs, the block cannot be used. Bit 7 of the flash memory control register 0 is the erase status flag. This bit is set to "1" when erasing flash memory is failed. When erase error occurs, the block cannot be used. Figure 79 shows the flash memory control register 1. Bit 0 of the flash memory control register 1 is the Erase suspend enable bit. By setting this bit to "1", the erase suspend mode to suspend erase processing temporaly when block erase command is executed can be used. In order to set this bit to "1", writing "0" and "1" in succession to bit 0. In order to set this bit to "0", write "0" only to bit 0. Bit 1 of the flash memory control register 1 is the erase suspend request bit. By setting this bit to "1" when erase suspend enable bit is "1", the erase processing is suspended. Bit 6 of the flash memory control register 1 is the erase suspend flag. This bit is cleared to "0" at the flash erasing.
0 : Busy (being written or erased) 1 : Ready CPU rewrite mode select bit (Note 1) 0 : CPU rewrite mode invalid 1 : CPU rewrite mode valid
8KB user block E/W enable bit (Notes 1, 2) 0 : E/W disabled 1 : E/W enabled Flash memory reset bit (Notes 3, 4) 0 : Normal operation 1 : reset Not used (do not write "1" to this bit.) User ROM area select bit (Note 5) 0 : Boot ROM area is accessed 1 : User ROM area is accessed
Program status flag 0: Pass 1: Error Erase status flag 0: Pass 1: Error Notes 1: For this bit to be set to "1", the user needs to write a "0" and then a "1" to it in succession. For this bit to be set to "0", write "0" only to this bit. 2: This bit can be written only when CPU rewrite mode select bit is "1". 3: Effective only when the CPU rewrite mode select bit = "1". Fix this bit to "0" when the CPU rewrite mode select bit is "0". 4: When setting this bit to "1" (when the control circuit of flash memory is reset), the flash memory cannot be accessed for 10 s. 5: Write to this bit in program on RAM
Fig. 78 Structure of flash memory control register 0
b7 b0 Flash memory control register 1 (FMCR1: address : 0FE116: initial value: 4016) Erase Suspend enble bit (Notes 1) 0 : Suspend invalid 1 : Suspend valid Erase Suspend request bit (Notes 2) 0 : Erase restart 1 : Suspend request Not used (do not write "1" to this bit.) Erase Suspend flag 0 : Erase active 1 : Erase inactive (Erase Suspend mode) Not used (do not write "1" to this bit.)
Notes 1: For this bit to be set to "1", the user needs to write a "0" and then a "1" to it in succession. For this bit to be set to "0", write "0" only to this bit. 2: Effective only when the suspend enable bit = "1".
Fig. 79 Structure of flash memory control register 1
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-82
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
b7
b0 Flash memory control register 2 (FMCR2: address : 0FE216: initial value: 4516) Not used Not used (do not write "1" to this bit.) Not used All user block E/W enable bit (Notes 1, 2) 0 : E/W disabled 1 : E/W enabled Not used
Notes 1: For this bit to be set to "1", the user needs to write a "0" and then a "1" to it in succession. For this bit to be set to "0", write "0" only to this bit. 2: Effective only when the CPU rewrite mode select bit = "1".
Fig. 80 Structure of flash memory control register 2 Table 14 State of E/W inhibition function All user block E/W enable bit 0 0 1 1 8 KB user block E/W enable bit 0 1 0 1 8 KB 2 block 16 KB + 24 KB block Data block Addresses C00016 to FFFF16 Addresses 200016 to BFFF16 Addresses 100016 to 1FFF16 E/W disabled E/W disabled E/W enabled E/W disabled E/W disabled E/W enabled E/W disabled E/W enabled E/W enabled E/W enabled E/W enabled E/W enabled
Figure 81 shows a flowchart for setting/releasing CPU rewrite mode.
Start
Single-chip mode or Boot mode
Set CPU mode register (Note 1)
Transfer CPU rewrite mode control program to internal RAM
Jump to control program transferred to internal RA M (Subsequent operations are executed by control program in this RAM)
Set CPU rewrite mode select bit to "1" (by writing "0" and then "1" in succession)
Set all user block E/W enable bit to "1" (by writing "0" and then "1" in succession) Set 8 KB user block E/W enable bit (At E/W disabled; writing "0", at E/W enabled; writing "0" and then "1" in succession)
Using software command executes erase, program, or other operation
Execute read array command (Note 2)
Set all user block E/W enable bit to "0" Set 8 KB user block E/W enable bit to "0"
Write "0" to CPU rewrite mode select bit
End Notes 1: Set the main clock as follows depending on the clock division ratio selection bits of CPU mode register (bits 6, 7 of address 003B16). 2: Before exiting the CPU rewrite mode after completing erase or program operation, always be sure to execute the read array command.
Fig. 81 CPU rewrite mode set/release flowchart
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-83
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
s Notes on CPU Rewrite Mode
Take the notes described below when rewriting the flash memory in CPU rewrite mode. qOperation speed During CPU rewrite mode, set the system clock to 4.0 MHz or less using the clock division ratio selection bits (bits 6 and 7 of address 003B16). qInstructions inhibited against use The instructions which refer to the internal data of the flash memory cannot be used during CPU rewrite mode. qInterrupts The interrupts cannot be used during CPU rewrite mode because they refer to the internal data of the flash memory. qWatchdog timer If the watchdog timer has been already activated, internal reset due to an underflow will not occur because the watchdog timer is surely cleared during program or erase. qReset Reset is always valid. The MCU is activated using the boot mode at release of reset in the condition of CNVss = "H", so that the program will begin at the address which is stored in addresses FFFC16 and FFFD16 of the boot ROM area.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-84
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
The RY/BY status flag of the flash memory control register is "0" during write operation and "1" when the write operation is completed as is the status register bit 7. At program end, program results can be checked by reading the status register.
q Software Commands
Table 15 lists the software commands. After setting the CPU rewrite mode select bit to "1", execute a software command to specify an erase or program operation. Each software command is explained below. * Read Array Command (FF16) The read array mode is entered by writing the command code "FF16" in the first bus cycle. When an address to be read is input in one of the bus cycles that follow, the contents of the specified address are read out at the data bus (D0 to D7). The read array mode is retained until another command is written. * Read Status Register Command (7016) When the command code "7016" is written in the first bus cycle, the contents of the status register are read out at the data bus (D0 to D7) by a read in the second bus cycle. The status register is explained in the next section. * Clear Status Register Command (5016) This command is used to clear the bits SR4 and SR5 of the status register after they have been set. These bits indicate that operation has ended in an error. To use this command, write the command code "5016" in the first bus cycle. * Program Command (4016) Program operation starts when the command code "4016" is written in the first bus cycle. Then, if the address and data to program are written in the 2nd bus cycle, program operation (data programming and verification) will start. Whether the write operation is completed can be confirmed by _____ read status register or the RY/BY status flag. When the program starts, the read status register mode is entered automatically and the contents of the status register is read at the data bus (D0 to D7). The status register bit 7 (SR7) is set to "0" at the same time the write operation starts and is returned to "1" upon completion of the write operation. In this case, the read status register mode remains active until the read array command (FF16) is written.
Start Write "4016" Write Write address Write data Read status register
SR7 = "1"? or RY/BY = "1" ? YES
NO
SR4 = "0"? YES Program completed
NO
Program error
Fig. 82 Program flowchart
Table 15 List of software commands (CPU rewrite mode)
Command Read array Read status register Clear status register Program Block erase
Cycle number 1 2 1 2 2
Mode Write Write Write Write Write
First bus cycle Data Address (D0 to D7) X
(Note 4)
Second bus cycle Mode Address Data (D0 to D7)
FF16 7016 5016 4016 2016 Write Write WA (Note 2) BA
(Note 3)
X X X X
Read
X
SRD (Note 1)
WD (Note 2) D016
Notes 1: SRD = Status Register Data 2: WA = Write Address, WD = Write Data 3: BA = Block Address to be erased (Input the maximum address of each block.) 4: X denotes a given address in the User ROM area.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-85
HARDWARE 3804 Group (Spec.H)
* Block Erase Command (2016/D016) By writing the command code "2016" in the first bus cycle and the confirmation command code "D016" and the block address in the second bus cycle that follows, the block erase (erase and erase verify) operation starts for the block address of the flash memory to be specified. Whether the block erase operation is completed can be confirmed by read status register or the RY/BY status flag of flash memory control register. At the same time the block erase operation starts, the read status register mode is automatically entered, so that the contents of the status register can be read out. The status register bit 7 (SR7) is set to "0" at the same time the block erase operation starts and is returned to "1" upon completion of the block erase operation. In this case, the read status register mode remains active until the read array command (FF16) is written. The RY/BY status flag is "0" during block erase operation and "1" when the block erase operation is completed as is the status register bit 7. After the block erase ends, erase results can be checked by reading the status register. For details, refer to the section where the status register is detailed.
FUNCTIONAL DESCRIPTION
Start
Write "2016"
Write
"D016" Block address
Read status register
SR7 = "1"? or RY/BY = "1"?
NO
YES NO
SR5 = "0" ?
Erase error
YES Erase completed (write read command "FF16")
Fig. 83 Erase flowchart
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-86
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
*Erase status (SR5) The erase status indicates the operating status of erase operation. If an erase error occurs, it is set to "1". When the erase status is cleared, it is reset to "0". *Program status (SR4) The program status indicates the operating status of write operation. When a write error occurs, it is set to "1". The program status is reset to "0" when it is cleared. If "1" is written for any of the SR5 and SR4 bits, the read array, program, and block erase commands are not accepted. Before executing these commands, execute the clear status register command (5016) and clear the status register. Also, if any commands are not correct, both SR5 and SR4 are set to "1".
q Status Register
The status register shows the operating status of the flash memory and whether erase operations and programs ended successfully or in error. It can be read in the following ways: (1) By reading an arbitrary address from the User ROM area after writing the read status register command (7016) (2) By reading an arbitrary address from the User ROM area in the period from when the program starts or erase operation starts to when the read array command (FF16) is input. Also, the status register can be cleared by writing the clear status register command (5016). After reset, the status register is set to "8016". Table 16 shows the status register. Each bit in this register is explained below. *Sequencer status (SR7) The sequencer status indicates the operating status of the flash memory. This bit is set to "0" (busy) during write or erase operation and is set to "1" when these operations ends. After power-on, the sequencer status is set to "1" (ready).
Table 16 Definition of each bit in status register
Each bit of SRD bits SR7 (bit7) SR6 (bit6) SR5 (bit5) SR4 (bit4) SR3 (bit3) SR2 (bit2) SR1 (bit1) SR0 (bit0)
Status name Sequencer status Reserved Erase status Program status Reserved Reserved Reserved Reserved
Definition
"1" Ready Terminated in error Terminated in error "0" Busy Terminated normally Terminated normally -
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-87
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
q Full Status Check
By performing full status check, it is possible to know the execution results of erase and program operations. Figure 84 shows a full status check flowchart and the action to be taken when each error occurs.
Read status register
SR4 = "1" and SR5 = "1" ? NO SR5 = "0" ? YES SR4 = "0" ? YES
YES
Command sequence error
Execute the clear status register command (5016) to clear the status register. Try performing the operation one more time after confirming that the command is entered correctly. Should an erase error occur, the block in error cannot be used.
NO
Erase error
NO
Program error
Should a program error occur, the block in error cannot be used.
End (block erase, program)
Note: When one of SR5 and SR4 is set to "1", none of the read array, program, and block erase commands is accepted. Execute the clear status register command (5016) before executing these commands.
Fig. 84 Full status check flowchart and remedial procedure for errors
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-88
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
If one or both of the pair of ROM code protect bits is set to "0", the ROM code protect is turned on, so that the contents of internal flash memory are protected against readout and modification. The ROM code protect is implemented in two levels. If level 2 is selected, the flash memory is protected even against readout by a shipment inspection LSI tester, etc. When an attempt is made to select both level 1 and level 2, level 2 is selected by default. If both of the two ROM code protect reset bits are set to "00", the ROM code protect is turned off, so that the contents of internal flash memory can be readout or modified. Once the ROM code protect is turned on, the contents of the ROM code protect reset bits cannot be modified in parallel I/O mode. Use the serial I/O or CPU rewrite mode to rewrite the contents of the ROM code protect reset bits. Rewriting of only the ROM code protect control address (address FFDB16) cannot be performed. When rewriting the ROM code protect reset bit, rewrite the whole user ROM area (block 0) containing the ROM code protect control address.
q Functions To Inhibit Rewriting Flash Memory Version
To prevent the contents of internal flash memory from being read out or rewritten easily, this MCU incorporates a ROM code protect function for use in parallel I/O mode and an ID code check function for use in standard serial I/O mode. (1) ROM Code Protect Function The ROM code protect function is the function to inhibit reading out or modifying the contents of internal flash memory by using the ROM code protect control address (address FFDB16) in parallel I/O mode. Figure 85 shows the ROM code protect control address (address FFDB16). (This address exists in the User ROM area.)
b7
b0
1 1 ROMCP (FF16 when shipped)
ROM code protect control address (address FFDB16)
Reserved bits ("1" at read/write) ROM code protect level 2 set bits (ROMCP2) (Notes 1, 2) b3b2 0 0: Protect enabled 0 1: Protect enabled 1 0: Protect enabled 1 1: Protect disabled ROM code protect reset bits (ROMCR) (Note 3) b5b4 0 0: Protect removed 0 1: Protect set bits effective 1 0: Protect set bits effective 1 1: Protect set bits effective ROM code protect level 1 set bits (ROMCP1) (Note 1) b7b6 0 0: Protect enabled 0 1: Protect enabled 1 0: Protect enabled 1 1: Protect disabled
Notes 1: When ROM code protect is turned on, the internal flash memory is protected against readout or modification in parallel I/O mode. 2: When ROM code protect level 2 is turned on, ROM code readout by a shipment inspection LSI tester, etc. also is inhibited. 3: The ROM code protect reset bits can be used to turn off ROM code protect level 1 and ROM code protect level 2. However, since these bits cannot be modified in parallel I/O mode, they need to be rewritten in serial I/O mode or CPU rewrite mode.
Fig. 85 Structure of ROM code protect control address
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-89
HARDWARE 3804 Group (Spec.H)
(2) ID Code Check Function Use this function in standard serial I/O mode. When the contents of the flash memory are not blank, the ID code sent from the programmer is compared with the ID code written in the flash memory to see if they match. If the ID codes do not match, the commands sent from the programmer are not accepted. The ID code consists of 8-bit data, and its areas are FFD416 to FFDA16. Write a program which has had the ID code preset at these addresses to the flash memory.
FUNCTIONAL DESCRIPTION
Address FFD416 FFD516 FFD616 FFD716 FFD816 FFD916 FFDA16 FFDB16 ID1 ID2 ID3 ID4 ID5 ID6 ID7 ROM code protect control Interrupt vector area
Fig. 86 ID code store addresses
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-90
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
q Parallel I/O Mode
The parallel I/O mode is used to input/output software commands, address and data in parallel for operation (read, program and erase) to internal flash memory. Use the external device (writer) only for 3804 Group (spec. H). For details, refer to the user's manual of each writer manufacturer.
* User ROM and Boot ROM Areas
In parallel I/O mode, the User ROM and Boot ROM areas shown in Figure 77 can be rewritten. Both areas of flash memory can be operated on in the same way. The Boot ROM area is 4 Kbytes in size and located at addresses F00016 through FFFF16. Make sure program and block erase operations are always performed within this address range. (Access to any location outside this address range is prohibited.) In the Boot ROM area, an erase block operation is applied to only one 4 Kbyte block. The boot ROM area has had a standard serial I/O mode control program stored in it when shipped from the fac-tory. Therefore, using the MCU in standard serial I/O mode, do not rewrite to the Boot ROM area.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-91
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
q Standard serial I/O Mode
The standard serial I/O mode inputs and outputs the software commands, addresses and data needed to operate (read, program, erase, etc.) the internal flash memory. This I/O is clock synchronized serial. This mode requires a purpose-specific peripheral unit. The standard serial I/O mode is different from the parallel I/O mode in that the CPU controls flash memory rewrite (uses the CPU rewrite mode), rewrite data input and so forth. The standard serial I/O mode is started by connecting "H" to the CNVss pin and "H" to the P45 (BOOTENT) pin, and releasing the reset operation. (In the ordinary microcomputer mode, set CNVss pin to "L" level.) This control program is written in the Boot ROM area when the product is shipped from Renesas. Accordingly, make note of the fact that the standard serial I/O mode cannot be used if the Boot ROM area is rewritten in parallel I/O mode. The standard serial I/ O mode has standard serial I/O mode 1 of the clock synchronous serial and standard serial I/O mode 2 of the clock asynchronous serial. Tables 17 and 18 show description of pin function (standard serial I/O mode). Figures 87 to 90 show the pin connections for the standard serial I/O mode. In standard serial I/O mode, only the User ROM area shown in Figure 77 can be rewritten. The Boot ROM area cannot be written. In standard serial I/O mode, a 7-byte ID code is used. When there is data in the flash memory, this function determines whether the ID code sent from the peripheral unit (programmer) and those written in the flash memory match. The commands sent from the peripheral unit (programmer) are not accepted unless the ID code matches.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-92
HARDWARE 3804 Group (Spec.H)
Table 17 Description of pin function (Flash Memory Serial I/O Mode 1) Pin name VCC,VSS CNVSS RESET XIN XOUT AVSS VREF P00-P07,P10-P17, P20-P27,P30-P37, P40-P43,P50-P57, P60-P67 P44 P45 P46 P47 Signal name Power supply CNVSS Reset input Clock input Clock output Analog power supply input Reference voltage input I/O port I/O I I I I O I I/O Function Apply 2.7 to 5.5 V to the Vcc pin and 0 V to the Vss pin. After input of port is set, input "H" level. Reset input pin. To reset the microcomputer, RESET pin should be held at an "L" level for 16 cycles or more of XIN. Connect an oscillation circuit between the XIN and XOUT pins. As for the connection method, refer to the "clock generating circuit". Connect AVss to Vss. Apply reference voltage of A/D to this pin. Input "L" or "H" level, or keep open.
FUNCTIONAL DESCRIPTION
RxD input TxD output SCLK input BUSY output
I O I O
Serial data input pin. Serial data output pin. Serial clock input pin. BUSY signal output pin.
Table 18 Description of pin function (Flash Memory Serial I/O Mode 2) Pin name VCC,VSS CNVSS RESET XIN XOUT AVss VREF P00-P07,P10-P17, P20-P27,P30-P37, P40-P43,P50-P57, P60-P67 P44 P45 P46 P47 Signal name Power supply CNVSS Reset input Clock input Clock output Analog power supply input Reference voltage input I/O port I/O I I I I O I I/O Function Apply 2.7 to 5.5 V to the Vcc pin and 0 V to the Vss pin. After input of port is set, input "H" level. Reset input pin. To reset the microcomputer, RESET pin should be held at an "L" level for 16 cycles or more of XIN. Connect an oscillation circuit between the XIN and XOUT pins. As for the connection method, refer to the "clock generating circuit". Connect AVss to Vss. Apply reference voltage of A/D to this pin. Input "L" or "H" level, or keep open.
RxD input TxD output SCLK input BUSY output
I O I O
Serial data input pin. Serial data output pin. Input "L" level. BUSY signal output pin.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-93
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
P02/AN10
P01/AN9
P00/AN8
P05/AN13
P06/AN14
P10/INT41
P04/AN12
P11/INT01
P03/AN11
P07/AN15
P12 P13
P14
P15 35
P16 34
48
46
45
44
41
40
43
42
39
38
47
37
36
P37/SRDY3 P36/SCLK3 P35/TXD3 P34/RXD3 P33/SCL P32/SDA P31/DA2 P30/DA1 VCC VCC VREF AVSS P67/AN7 P66/AN6 P65/AN5 P64/AN4 P63/AN3
49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64
33
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17
P17
P20(LED0) P21(LED1) P22(LED2) P23(LED3) P24(LED4) P25(LED5) P26(LED6) P27(LED7) VSS XOUT XIN P40/INT40/XCOUT P41/INT00/XCIN RESET CNVSS P42/INT1 RESET CNVss VSS
M38049FFHFP/HP/KP
13
12
10
11
P56/PWM
P54/CNTR0
P53/SRDY2
P51/SOUT2
P45/TXD1 P44/RXD1
P62/AN2
P60/AN0
P57/INT3
14
15
P55/CNTR1
P52/SCLK2
P47/SRDY1/CNTR2
Connect oscillation circuit. indicates flash memory pin.
P46/SCLK1
P43/INT2
P61/AN1
P50/SIN2
16
2
5
4
1
3
6
7
8
9
RxD TxD SCLK BUSY
Package type: 64P6N-A/64P6Q-A/64P6U-A
Fig. 87 Connection for standard serial I/O mode 1 (M38049FFHFP/HP/KP)
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-94
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
P02/AN10
P01/AN9
P00/AN8
P05/AN13
P06/AN14
P10/INT41
P04/AN12
P11/INT01
P03/AN11
P07/AN15
P12 P13
P14
P15 35
P16 34
48
46
45
47
44
41
40
43
42
39
38
37
36
P37/SRDY3 P36/SCLK3 P35/TXD3 P34/RXD3 P33/SCL P32/SDA P31/DA2 P30/DA1 VCC VCC VREF AVSS P67/AN7 P66/AN6 P65/AN5 P64/AN4 P63/AN3
49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64
33
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17
P17
P20(LED0) P21(LED1) P22(LED2) P23(LED3) P24(LED4) P25(LED5) P26(LED6) P27(LED7) VSS XOUT XIN P40/INT40/XCOUT P41/INT00/XCIN RESET CNVSS P42/INT1 RESET CNVss VSS
M38049FFHFP/HP/KP
13
12
10
11
P56/PWM
P54/CNTR0
P53/SRDY2
P51/SOUT2
P45/TXD1 P44/RXD1
P62/AN2
P60/AN0
P57/INT3
14
15
P55/CNTR1
P52/SCLK2
P47/SRDY1/CNTR2
Connect oscillation circuit. indicates flash memory pin.
P46/SCLK1
P43/INT2
P61/AN1
P50/SIN2
16
2
5 6
4
1
3
7
8
9
RxD TxD "L" input BUSY
Package type: 64P6N-A/64P6Q-A/64P6U-A
Fig. 88 Connection for standard serial I/O mode 2 (M38049FFHFP/HP/KP)
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-95
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
VCC
BUSY SCLK TXD RXD CNVSS RESET
VSS
VCC VREF AVSS P67/AN7 P66/AN6 P65/AN5 P64/AN4 P63/AN3 P62/AN2 P61/AN1 P60/AN0 P57/INT3 P56/PWM P55/CNTR1 P54/CNTR0 P53/SRDY2 P52/SCLK2 P51/SOUT2 P50/SIN2 P47/SRDY1/CNTR2 P46/SCLK1 P45/TXD1 P44/RXD1 P43/INT2 P42/INT1 CNVSS RESET P41/INT00/XCIN P40/INT40/XCOUT XIN XOUT VSS
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33
P30/DA1 P31/DA2 P32/SDA P33/SCL P34/RXD3 P35/TXD3 P36/SCLK3 P37/SRDY3 P00/AN8 P01/AN9 P02/AN10 P03/AN11 P04/AN12 P05/AN13 P06/AN14 P07/AN15 P10/INT41 P11/INT01 P12 P13 P14 P15 P16 P17 P20(LED0) P21(LED1) P22(LED2) P23(LED3) P24(LED4) P25(LED5) P26(LED6) P27(LED7)
M38049FFHSP
Connect oscillation circuit. indicates flash memory pin.
Package type: 64P4B
Fig. 89 Connection for standard serial I/O mode 1 (M38049FFHSP)
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-96
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
VCC
BUSY "L" input TXD RXD CNVSS RESET
VSS
VCC VREF AVSS P67/AN7 P66/AN6 P65/AN5 P64/AN4 P63/AN3 P62/AN2 P61/AN1 P60/AN0 P57/INT3 P56/PWM P55/CNTR1 P54/CNTR0 P53/SRDY2 P52/SCLK2 P51/SOUT2 P50/SIN2 P47/SRDY1/CNTR2 P46/SCLK1 P45/TXD1 P44/RXD1 P43/INT2 P42/INT1 CNVSS RESET P41/INT00/XCIN P40/INT40/XCOUT XIN XOUT VSS
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33
P30/DA1 P31/DA2 P32/SDA P33/SCL P34/RXD3 P35/TXD3 P36/SCLK3 P37/SRDY3 P00/AN8 P01/AN9 P02/AN10 P03/AN11 P04/AN12 P05/AN13 P06/AN14 P07/AN15 P10/INT41 P11/INT01 P12 P13 P14 P15 P16 P17 P20(LED0) P21(LED1) P22(LED2) P23(LED3) P24(LED4) P25(LED5) P26(LED6) P27(LED7)
M38049FFHSP
Connect oscillation circuit. indicates flash memory pin.
Package type: 64P4B
Fig. 90 Connection for standard serial I/O mode 2 (M38049FFHSP)
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-97
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION
td(CNVSS-RESET) td(P45-RESET)
Power source RESET CNVSS P45(TXD) P46(SCLK) P47(BUSY) P44(RXD)
Symbol td(CNVss-RESET) td(P45-RESET)
Limits Unit Min. Typ. Max. - - ms 0 ms 0
Notes: In the standard serial I/O mode 1, input "H" to the P46 pin. Be sure to set the CNVss pin to "H" before rising RESET. Be sure to set the P45 pin to "H" before rising RESET.
Fig. 91 Operating waveform for standard serial I/O mode 1
td(CNVSS-RESET) td(P45-RESET)
Power source RESET CNVSS P45(TXD) P46(SCLK) P47(BUSY) P44(RXD)
Symbol td(CNVss-RESET) td(P45-RESET)
Limits Unit Min. Typ. Max. ms - - 0 ms 0
Notes: In the standard serial I/O mode 2, input "H" to the P46 pin. Be sure to set the CNVss pin to "H" before rising RESET. Be sure to set the P45 pin to "H" before rising RESET.
Fig. 92 Operating waveform for standard serial I/O mode 2
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-98
HARDWARE 3804 Group (Spec.H) NOTES ON PROGRAMMING
NOTES ON PROGRAMMING Processor Status Register
The contents of the processor status register (PS) after a reset are undefined, except for the interrupt disable flag (I) which is "1." After a reset, initialize flags which affect program execution. In particular, it is essential to initialize the index X mode (T) and the decimal mode (D) flags because of their effect on calculations.
Serial Interface
In clock synchronous serial I/O, if the receive side is using an external clock and it is to output the SRDY signal, set the transmit enable bit, the receive enable bit, and the SRDY output enable bit to "1." Serial I/O continues to output the final bit from the TXD pin after transmission is completed. SOUT2 pin for serial I/O2 goes to high impedance after transfer is completed. When in serial I/Os 1 and 3 (clock-synchronous mode) or in serial I/O2, an external clock is used as synchronous clock, write transmission data to the transmit buffer register or serial I/O2 register, during transfer clock is "H."
Interrupts
The contents of the interrupt request bits do not change immediately after they have been written. After writing to an interrupt request register, execute at least one instruction before performing a BBC or BBS instruction.
A/D Converter
The comparator uses capacitive coupling amplifier whose charge will be lost if the clock frequency is too low. Therefore, make sure that f(XIN) is at least on 500 kHz during an A/D conversion. Do not execute the STP instruction during an A/D conversion.
Decimal Calculations
* To calculate in decimal notation, set the decimal mode flag (D) to "1", then execute an ADC or SBC instruction. After executing an ADC or SBC instruction, execute at least one instruction before executing a SEC, CLC, or CLD instruction. * In decimal mode, the values of the negative (N), overflow (V), and zero (Z) flags are invalid.
D/A Converter
The accuracy of the D/A converter becomes rapidly poor under the VCC = 4.0 V or less condition; a supply voltage of VCC 4.0 V is recommended. When a D/A converter is not used, set all values of D/Ai conversion registers (i=1, 2) to "0016."
Timers
If a value n (between 0 and 255) is written to a timer latch, the frequency division ratio is 1/(n+1).
Instruction Execution Time Multiplication and Division Instructions
* The index X mode (T) and the decimal mode (D) flags do not affect the MUL and DIV instruction. * The execution of these instructions does not change the contents of the processor status register. The instruction execution time is obtained by multiplying the period of the internal clock by the number of cycles needed to execute an instruction. The number of cycles required to execute an instruction is shown in the list of machine instructions. The period of the internal clock is double of the XIN period in high-speed mode.
Ports
The contents of the port direction registers cannot be read. The following cannot be used: * The data transfer instruction (LDA, etc.) * The operation instruction when the index X mode flag (T) is "1" * The instruction with the addressing mode which uses the value of a direction register as an index * The bit-test instruction (BBC or BBS, etc.) to a direction register * The read-modify-write instructions (ROR, CLB, or SEB, etc.) to a direction register. Use instructions such as LDM and STA, etc., to set the port direction registers.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-99
HARDWARE 3804 Group (Spec.H) NOTES ON USAGE
NOTES ON USAGE Handling of Power Source Pins
In order to avoid a latch-up occurrence, connect a capacitor suitable for high frequencies as bypass capacitor between power source pin (VCC pin) and GND pin (VSS pin), and between power source pin (VCC pin) and analog power source input pin (AVSS pin). Besides, connect the capacitor to as close as possible. For bypass capacitor which should not be located too far from the pins to be connected, a ceramic capacitor of 0.01 F-0.1 F is recommended.
Power Source Voltage
When the power source voltage value of a microcomputer is less than the value which is indicated as the recommended operating conditions, the microcomputer does not operate normally and may perform unstable operation. In a system where the power source voltage drops slowly when the power source voltage drops or the power supply is turned off, reset a microcomputer when the power source voltage is less than the recommended operating conditions and design a system not to cause errors to the system by this unstable operation.
Flash Memory Version
The CNVss pin determines the flash memory mode. To improve the noise reduction, connect a track between CNVss pin and Vss pin or Vcc pin with 1 to 10 k resistance. The mask ROM version track of CNVss pin has no operational interference even if it is connected to Vss pin or Vcc pin via a resistor.
Electric Characteristic Differences Between Mask ROM and Flash Memory Version MCUs
There are differences in electric characteristics, operation margin, noise immunity, and noise radiation between Mask ROM and Flash Memory version MCUs due to the difference in the manufacturing processes, built-in ROM, and layout pattern etc.When manufacturing an application system with the Flash Memory version and then switching to use of the Mask ROM version, please conduct evaluations equivalent to the system evaluations conducted for the flash memory version.
DATA REQUIRED FOR MASK ORDERS
The following are necessary when ordering a mask ROM production: 1.Mask ROM Confirmation Form 2.Mark Specification Form 3.Data to be written to ROM, in EPROM form (three identical copies) For the mask ROM confirmation and the mark specifications, refer to the "Renesas Technology Corp." Homepage (http://www.renesas.com/en/rom).
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-100
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION SUPPLEMENT
FUNCTIONAL DESCRIPTION SUPPLEMENT Interrupt
The 3804 group (Spec. H) permits interrupts on the basis of 16 sources. It is vector interrupts with a fixed priority system. Accordingly, when two or more interrupt requests occur during the same sampling, the higher-priority interrupt is accepted first. This priority is determined by hardware, but variety of priority processing can be performed by software, using an interrupt enable bit and an interrupt disable flag. For interrupt sources, vector addresses and interrupt priority, refer to "Table 19".
Table 19 Interrupt sources, vector addresses and priority Interrupt Source Reset (Note 2) INT0 Timer Z INT1 Serial I/O1 reception Serial I/O1 transmission SCL, SDA Timer X Timer Y Timer 1 Timer 2 CNTR0 SCL, SDA CNTR1 Serial I/O3 reception Serial I/O2 Timer Z INT2 I 2C INT3 INT4 CNTR2 A/D converter Serial I/O3 transmission BRK instruction 16 FFDF16 FFDE16 11 FFE916 FFE816 6 7 8 9 10 FFF316 FFF116 FFEF16 FFED16 FFEB16 FFF216 FFF016 FFEE16 FFEC16 FFEA16 Priority 1 2 Vector Addresses (Note 1) Low High FFFC16 FFFD16 FFFB16 FFFA16 Interrupt Request Generating Conditions At reset At detection of either rising or falling edge of INT0 input At timer Z underflow At detection of either rising or falling edge of INT1 input At completion of serial I/O1 data reception At completion of serial I/O1 transmission shift or when transmission buffer is empty At detection of either rising or falling edge of SCL or SDA At timer X underflow At timer Y underflow At timer 1 underflow At timer 2 underflow At detection of either rising or falling edge of CNTR0 input At detection of either rising or falling edge of SCL or SDA At detection of either rising or falling edge of CNTR1 input At completion of serial I/O3 data reception 12 FFE716 FFE616 At completion of serial I/O2 data transmission or reception At timer Z underflow 13 FFE516 FFE416 At detection of either rising or falling edge of INT2 input At completion of data transfer At detection of either rising or falling edge of INT3 input At detection of either rising or falling edge of INT4 input At detection of either rising or falling edge of CNTR2 input At completion of A/D conversion At completion of serial I/O3 transmission shift or when transmission buffer is empty 17 FFDD16 FFDC16 At BRK instruction execution Valid when serial I/O3 is selected External interrupt (active edge selectable) External interrupt (active edge selectable) External interrupt (active edge selectable) External interrupt (active edge selectable) External interrupt (active edge selectable) External interrupt (active edge selectable) External interrupt (active edge selectable) Valid when serial I/O3 is selected Valid when serial I/O2 is selected STP release timer underflow Remarks Non-maskable External interrupt (active edge selectable) External interrupt (active edge selectable) Valid when serial I/O1 is selected Valid when serial I/O1 is selected
3 4 5
FFF916 FFF716 FFF516
FFF816 FFF616 FFF416
External interrupt (active edge selectable)
14 15
FFE316 FFE116
FFE216 FFE016
Non-maskable software interrupt
Notes 1: Vector addresses contain interrupt jump destination addresses. 2: Reset function in the same way as an interrupt with the highest priority.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-101
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION SUPPLEMENT
Timing After Interrupt
The interrupt processing routine begins with the machine cycle following the completion of the instruction that is currently in execution. Figure 93 shows a timing chart after an interrupt occurs, and Figure 94 shows the time up to execution of the interrupt processing routine.
SYNC RD WR Address bus Data bus PC Not used
S, SPS S-1, SPS S-2, SPS
BL AL
BH
AL, AH AH
PCH
PCL
PS
SYNC : CPU operation code fetch cycle (This is an internal signal that cannot be observed from the external unit.) BL, BH : Vector address of each interrupt AL, AH : Jump destination address of each interrupt SPS : "0016" or "0116"
Fig. 93 Timing chart after an interrupt occurs
Interrupt request generated
Start of interrupt processing
Main routine
Waiting time for Stack push and post-processing Vector fetch of pipeline
Interrupt processing routine
0 to 16 cycles
2 cycles
5 cycles
7 to 23 cycles (When f(XIN) = 8.4 MHz, 0.83 s to 2.74 s)
Fig. 94 Time up to execution of the interrupt processing routine
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-102
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION SUPPLEMENT
A/D Converter
A/D conversion is started by setting AD conversion completion bit to "0". During A/D conversion, internal operations are performed as follows. 1. After the start of A/D conversion, AD conversion register goes to "0016". 2. The highest-order bit of AD conversion register is set to "1". and the comparison voltage Vref is input to the comparator. Then, Vref is compared with analog input voltage VIN. 3. As a result of comparison, when Vref < VIN, the highestorder bit of AD conversion register becomes "1." When Vref > VIN, the highest-order bit becomes "0."
By repeating the above operations up to the lowest-order bit of the AD conversion register, an analog value converts into a digital value. In the 10-bit A/D mode, A/D conversion completes at 61 cycles of 2tc(XIN)* (15.25 s at f(XIN) = 8.0 MHz) after it is started. In the 8bit A/D mode, A/D conversion completes at 50 cycles of 2tc(XIN) (12.5 s at f(XIN) = 8.0 MHz) after it is started. And the result of the conversion is stored into the AD conversion register. Concurrently with the completion of A/D conversion, the A/D conversion completion bit is set to "1" and an A/D conversion interrupt request occurs, so that the AD conversion interrupt request bit is set to "1". * tc(XIN) = Main clock input cycle time
Table 20 Relative formula for a reference voltage VREF of A/D converter and Vref (at 10-bit A/D mode) When n = 0 When n = 1 to 1023 Vref = 0 Vref = VREF 1024 n
n : Value of A/D converter (decimal numeral) Table 21 Relative formula for a reference voltage VREF of A/D converter and Vref (at 8-bit A/D mode) When n = 0 When n = 1 to 255 Vref = 0 Vref = VREF 256 (n - 0.5)
n : Value of A/D converter (decimal numeral) Table 22 Change of AD conversion register during A/D conversion (at 10-bit A/D mode) Change of AD conversion register At start of conversion First comparison Second comparison Third comparison 0 1
1
Value of comparison voltage (Vref) 0 0 0 0 0 0 0 0 VREF 2 VREF 2 VREF 2 VREF 4 VREF 4 VREF 8 0
0 0 1
0 0 0 1
0 0 0 0
0 0 0 0
0 0 0 0
0 0 0 0
0 0 0 0
1
2
* * *
After completion of tenth comparison
* * *
A result of A/D conversion 1
* * *
6 7 8 9 10
2
3
4
5
VREF 2
VREF 4
***
VREF 1024
1-10: A result of the first to tenth comparison
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-103
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION SUPPLEMENT
Table 23 Change of AD conversion register during A/D conversion (at 8-bit A/D mode) Change of AD conversion register At start of conversion First comparison Second comparison Third comparison 0 1
1
Value of comparison voltage (Vref) 0 0 0 0 VREF 2 VREF 2 VREF 2 - VREF 512 VREF 4 VREF 4 - VREF 512 VREF 8 - VREF 512 0
0 0 1
0 0 0 1
0 0 0 0
0 0 0 0
0 0 0 0
0 0 0 0
1
2
* * *
After completion of eighth comparison
* * *
A result of A/D conversion 1
* * *
6 7 8
2
3
4
5
VREF 2
VREF 4
***
VREF 256
-
VREF 512
1-8: A result of the first to eighth comparison Figure 95 shows A/D conversion equivalent circuit, and Figure 96 shows A/D conversion timing chart.
VCC About 2 k AN0 AN1 AN2 AN3 AN4 AN5 AN6 AN7 AN8 AN9 AN10 AN11 AN12 AN13 AN14 AN15
VSS VIN
Sampling clock
VCC
AVSS
C
Chopper amplifier
AD conversion register 1
AD conversion register 2
AD conversion interrupt request
b4 b2 b1 b0 AD/DA control register
VREF
Built-in D/A converter
Vref
Reference clock
AVSS
Fig. 95 A/D conversion equivalent circuit
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-104
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION SUPPLEMENT
XIN 2 Write signal for AD control register AD conversion completion bit
At 10-bit A/D mode : 61 cycles At 8-bit A/D mode : 50 cycles
Sampling clock
Fig. 96 A/D conversion timing chart
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-105
HARDWARE 3804 Group (Spec.H) FUNCTIONAL DESCRIPTION SUPPLEMENT
Memo
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
1-106
CHAPTER 2 APPLICATION
2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 2.10 2.11 2.12 2.13 I/O port Interrupt Timer Serial interface Multi-master I2C-BUS interface PWM A/D converter D/A converter Watchdog timer Reset Clock generating circuit Standby function Flash memory mode
APPLICATION 3804 Group (Spec.H) 2.1 I/O port
2.1 I/O port
This paragraph describes the setting method of I/O port relevant registers, notes etc. 2.1.1 Memory map
Address 000016 000116 000216 000316 000416 000516 000616 000716 000816 000916 000A16 000B16 000C16 000D16 Port P0 (P0) Port P0 direction register (P0D) Port P1 (P1) Port P1 direction register (P1D) Port P2 (P2) Port P2 direction register (P2D) Port P3 (P3) Port P3 direction register (P3D) Port P4 (P4) Port P4 direction register (P4D) Port P5 (P5) Port P5 direction register (P5D) Port P6 (P6) Port P6 direction register (P6D)
0FF016 0FF116 0FF216 0FF316 0FF416 0FF516
Port P0 pull-up control register (PULL0) Port P1 pull-up control register (PULL1) Port P2 pull-up control register (PULL2) Port P3 pull-up control register (PULL3) Port P4 pull-up control register (PULL4) Port P5 pull-up control register (PULL5)
0FF616 Port P6 pull-up control register (PULL6)
Fig. 2.1.1 Memory map of I/O port relevant registers
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-2
APPLICATION 3804 Group (Spec.H) 2.1 I/O port
2.1.2 Relevant registers
Port Pi
b7 b6 b5 b4 b3 b2 b1 b0 Port Pi (i = 0, 1, 2, 3, 4, 5, 6) (Pi: addresses 000016, 000216, 000416, 000616, 000816, 000A16, 000C16)
b
0 1 2 3 4 5 6 7
Name
Port Pi0 Port Pi1 Port Pi2 Port Pi3 Port Pi4 Port Pi5 Port Pi6 Port Pi7
Functions
qIn output mode Write ******** Port latch Read ******** Port latch qIn input mode Write ******** Port latch Read ******** Value of pin
At reset R W
0 0 0 0 0 0 0 0
Fig. 2.1.2 Structure of Port Pi (i = 0 to 6)
Port Pi direction register
b7 b6 b5 b4 b3 b2 b1 b0 Port Pi direction register (i = 0, 1, 2, 3, 4, 5, 6) (PiD: addresses 000116, 000316, 000516, 000716, 000916, 000B16, 000D16)
b
Name
Functions
0 : Port Pi0 input mode 1 : Port Pi0 output mode 0 : Port Pi1 input mode 1 : Port Pi1 output mode 0 : Port Pi2 input mode 1 : Port Pi2 output mode 0 : Port Pi3 input mode 1 : Port Pi3 output mode 0 : Port Pi4 input mode 1 : Port Pi4 output mode 0 : Port Pi5 input mode 1 : Port Pi5 output mode 0 : Port Pi6 input mode 1 : Port Pi6 output mode 0 : Port Pi7 input mode 1 : Port Pi7 output mode
At reset R W
0 0 0 0 0 0 0 0
0 Port Pi direction register 1 2 3 4 5 6 7
Fig. 2.1.3 Structure of Port Pi direction register (i = 0 to 6)
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-3
APPLICATION 3804 Group (Spec.H) 2.1 I/O port
Port Pi pull-up control register (i = 0 to 2, 4 to 6)
b7 b6 b5 b4 b3 b2 b1 b0 Port Pi pull-up control register (i = 0 to 2, 4 to 6) (PULLi: addresses 0FF016, 0FF116, 0FF216, 0FF416, 0FF516, 0FF616)
b
Name
Functions
0: No pull-up 1: Pull-up 0: No pull-up 1: Pull-up 0: No pull-up 1: Pull-up 0: No pull-up 1: Pull-up 0: No pull-up 1: Pull-up 0: No pull-up 1: Pull-up 0: No pull-up 1: Pull-up 0: No pull-up 1: Pull-up
At reset R W
0 0 0 0 0 0 0 0
0 Port Pi0 pull-up control bit 1 Port Pi1 pull-up control bit 2 Port Pi2 pull-up control bit 3 Port Pi3 pull-up control bit 4 Port Pi4 pull-up control bit 5 Port Pi5 pull-up control bit 6 Port Pi6 pull-up control bit 7 Port Pi7 pull-up control bit
Fig. 2.1.4 Structure of Port Pi pull-up control register (i = 0, 1, 2, 4, 5, 6)
Port P3 pull-up control register
b7 b6 b5 b4 b3 b2 b1 b0 Port P3 pull-up control register (PULL3: address 0FF316)
b
Name
Functions
At reset R W
0 0 0 0 0 0 0 0 0
0: No pull-up 0 Port P30 pull-up control bit 1: Pull-up Port P31 pull-up 0: No pull-up 1 control bit 1: Pull-up 2 Nothing is arranged for these bits. These are write disabled bits. When these bits are read 3 out, the contents are "0". 0: No pull-up 4 Port P34 pull-up control bit 1: Pull-up 5 Port P35 pull-up 0: No pull-up control bit 1: Pull-up 0: No pull-up 6 Port P36 pull-up control bit 1: Pull-up Port P37 pull-up 7 0: No pull-up control bit 1: Pull-up
Fig. 2.1.5 Structure of Port P3 pull-up control register
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-4
APPLICATION 3804 Group (Spec.H) 2.1 I/O port
2.1.3 Port Pi pull-up control register Valid/Invalid of pull-up resistor can be set by the pull-up control register by a bit unit. Pull-up control is valid only when each direction register is set to the input mode. Note: Ports P32 and P33 do not have pull-up control bit because they are N-channel open-drain output. 2.1.4 Terminate unused pins Table 2.1.1 Termination of unused pins (in single-chip mode) Pins Termination P0, P1, P2, P3, * Set to the input mode and connect each to VCC or VSS through a resistor of 1 k to P4, P5, P6 10 k. * Set to the output mode and open at "L" or "H" output state. VREF AVSS XOUT Connect to Vss (GND). Connect to Vss (GND). Open (only when using external clock)
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-5
APPLICATION 3804 Group (Spec.H) 2.1 I/O port
2.1.5 Notes on I/O port (1) Notes in standby state In standby state 1 for low-power dissipation, do not make input levels of an I/O port "undefined", especially for I/O ports of the N-channel open-drain. Pull-up (connect the port to VCC) or pull-down (connect the port to VSS) these ports through a resistor. When determining a resistance value, note the following points: * External circuit * Variation of output levels during the ordinary operation When using built-in pull-up resistor, note on varied current values: * When setting as an input port : Fix its input level * When setting as an output port : Prevent current from flowing out to external q Reason Even when setting as an output port with its direction register, when the content of the port latch is "1", the transistor becomes the OFF state, which causes the ports to be the high-impedance state. Note that the level becomes "undefined" depending on external circuits. Accordingly, the potential which is input to the input buffer in a microcomputer is unstable in the state that input levels of an I/O port are "undefined". This may cause power source current. 1 standby state: stop mode by executing STP instruction wait mode by executing WIT instruction (2) Modifying output data with bit managing instruction When the port latch of an I/O port is modified with the bit managing instruction2, the value of the unspecified bit may be changed. q Reason The bit managing instructions are read-modify-write form instructions for reading and writing data by a byte unit. Accordingly, when these instructions are executed on a bit of the port latch of an I/O port, the following is executed to all bits of the port latch. *As for bit which is set for input port: The pin state is read in the CPU, and is written to this bit after bit managing. *As for bit which is set for output port: The bit value is read in the CPU, and is written to this bit after bit managing. Note the following: *Even when a port which is set as an output port is changed for an input port, its port latch holds the output data. *As for a bit of which is set for an input port, its value may be changed even when not specified with a bit managing instruction in case where the pin state differs from its port latch contents. 2 Bit managing instructions: SEB and CLB instructions
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-6
APPLICATION 3804 Group (Spec.H) 2.1 I/O port
2.1.6 Termination of unused pins (1) Terminate unused pins I/O ports : * Set the I/O ports for the input mode and connect them to VCC or VSS through each resistor of 1 k to 10 k. Ports that permit the selecting of a built-in pull-up resistor can also use this resistor. Set the I/O ports for the output mode and open them at "L" or "H". * When opening them in the output mode, the input mode of the initial status remains until the mode of the ports is switched over to the output mode by the program after reset. Thus, the potential at these pins is undefined and the power source current may increase in the input mode. With regard to an effects on the system, thoroughly perform system evaluation on the user side. * Since the direction register setup may be changed because of a program runaway or noise, set direction registers by program periodically to increase the reliability of program. The AVss pin when not using the A/D converter : * When not using the A/D converter, handle a power source pin for the A/D converter, AVss pin as follows: AVss: Connect to the Vss pin. (2) Termination remarks I/O ports : Do not open in the input mode. q Reason * The power source current may increase depending on the first-stage circuit. * An effect due to noise may be easily produced as compared with proper termination and shown on the above. I/O ports : When setting for the input mode, do not connect to VCC or VSS directly. q Reason If the direction register setup changes for the output mode because of a program runaway or noise, a short circuit may occur between a port and VCC (or VSS). I/O ports : When setting for the input mode, do not connect multiple ports in a lump to VCC or VSS through a resistor. q Reason If the direction register setup changes for the output mode because of a program runaway or noise, a short circuit may occur between ports. * At the termination of unused pins, perform wiring at the shortest possible distance (20 mm or less) from microcomputer pins.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-7
APPLICATION 3804 Group (Spec.H) 2.2 Interrupt
2.2 Interrupt
This paragraph explains the registers setting method and the notes relevant to the interrupt. 2.2.1 Memory map
003916 003A16 003C16 003D16 003E16 003F16
Interrupt source selection register (INTSEL) Interrupt edge selection register (INTEDGE)
Interrupt request register 1 (IREQ1) Interrupt request register 2 (IREQ2) Interrupt control register 1 (ICON1) Interrupt control register 2 (ICON2)
Fig. 2.2.1 Memory map of registers relevant to interrupt 2.2.2 Relevant registers
Interrupt source selection register
b7 b6 b5 b4 b3 b2 b1 b0 Interrupt source selection register (INTSEL: address 003916)
b
Name
Functions
0: INT0 interrupt 1: Timer Z interrupt 0: Serial I/O2 interrupt 1: Timer Z interrupt 0: Serial I/O1 transmit interrupt 1: SCL, SDA interrupt 0: CNTR0 interrupt 1: SCL, SDA interrupt 0: INT4 interrupt 1: CNTR2 interrupt 0: INT2 interrupt 1: I2C interrupt 0: CNTR1 interrupt 1: Serial I/O3 receive interrupt 0: A/D converter interrupt 1: Serial I/O3 transmit interrupt
At reset R W
0
0 INT0/Timer Z interrupt source selection bit (*1) 1 Serial I/O2/Timer Z interrupt source selection bit (*1) 2 Serial I/O1 transmit/ SCL, SDA interrupt source selection bit (*2) 3 CNTR0/SCL, SDA interrupt source selection bit (*2) 4 INT4/CNTR2 interrupt source selection bit 5 INT2/I2C interrupt source selection bit 6 CNTR1/Serial I/O3 receive interrupt source selection bit 7 AD converter/Serial I/O3 transmit interrupt source selection bit
0
0
0
0
0 0
0
*1: Do not write 1 to these bits simultaneously. *2: Do not write 1 to these bits simultaneously.
Fig. 2.2.2 Structure of Interrupt source selection register
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-8
APPLICATION 3804 Group (Spec.H) 2.2 Interrupt
Interrupt edge selection register
b7 b6 b5 b4 b3 b2 b1 b0 Interrupt edge selection register (INTEDGE: address 003A16)
b
Name
Functions
At reset R W
0 0 0
0: Falling edge active 0 INT0 active edge 1: Rising edge active selection bit 0: Falling edge active 1 INT1 active edge 1: Rising edge active selection bit 2 Nothing is arranged for this bit. This is a write disabled bit. When this bit is read out, the contents are "0". 3 INT2 active edge 0: Falling edge active selection bit 1: Rising edge active 4 INT3 active edge 0: Falling edge active selection bit 1: Rising edge active 0: Falling edge active 5 INT4 active edge selection bit 1: Rising edge active 6 INT0, INT4 interrupt 0: INT00, INT40 interrupt switch bit 1: INT01, INT41 interrupt 7 Nothing is arranged for this bit. This is a write disabled bit. When this bit is read out, the contents are "0".
0 0 0 0 0
Fig. 2.2.3 Structure of Interrupt edge selection register
Interrupt request register 1
b7 b6 b5 b4 b3 b2 b1 b0 Interrupt request register 1 (IREQ1 : address 003C16)
b
Name
Functions
At reset R W
0 0 0 0
0 INT0/Timer Z 0 : No interrupt request issued interrupt request bit 1 : Interrupt request issued 1 INT1 interrupt request bit
0 : No interrupt request issued
1 : Interrupt request issued
2 Serial I/O1 receive 0 : No interrupt request issued interrupt request bit 1 : Interrupt request issued
0 : No interrupt request issued 3 Serial I/O1 transmit/SCL, SDA 1 : Interrupt request issued interrupt request bit
4 Timer X interrupt request bit 5 Timer Y interrupt request bit 6 Timer 1 interrupt request bit
0 : No interrupt request issued
0 0 0 0

1 : Interrupt request issued
0 : No interrupt request issued
1 : Interrupt request issued
0 : No interrupt request issued
1 : Interrupt request issued
7 Timer 2 interrupt 0 : No interrupt request issued request bit 1 : Interrupt request issued : 0 can be set by software, but 1 cannot be set.
Fig. 2.2.4 Structure of Interrupt request register 1
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-9
APPLICATION 3804 Group (Spec.H) 2.2 Interrupt
Interrupt request register 2
b7 b6 b5 b4 b3 b2 b1 b0 Interrupt request register 2 (IREQ2 : address 003D16)
b
Name
Functions
0 : No interrupt request issued 1 : Interrupt request issued 0 : No interrupt request issued 1 : Interrupt request issued 0 : No interrupt request issued 1 : Interrupt request issued 0 : No interrupt request issued 1 : Interrupt request issued 0 : No interrupt request issued 1 : Interrupt request issued 0 : No interrupt request issued 1 : Interrupt request issued 0 : No interrupt request issued 1 : Interrupt request issued
At reset R W
0 0
0 CNTR0/SCL, SDA interrupt request bit 1 CNTR1/Serial I/O3 receive interrupt request bit 2 Serial I/O2/Timer Z interrupt request bit 3 INT2/I2C interrupt request bit 4 INT3 interrupt request bit 5 INT4/CNTR2 interrupt request bit 6 AD converter/Serial I/O3 transmit interrupt request bit
0 0 0 0 0

7 Nothing is arranged for this bit. This is a write disabled bit. When this bit is read out, the contents are 0 . : 0 can be set by software, but 1 cannot be set.
0
Fig. 2.2.5 Structure of Interrupt request register 2
Interrupt control register 1
b7 b6 b5 b4 b3 b2 b1 b0 Interrupt control register 1 (ICON1 : address 003E16)
b
Name
Functions
0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled
At reset R W
0 0 0 0
0 INT0/Timer Z interrupt enable bit 1 INT1 interrupt enable bit 2 Serial I/O1 receive interrupt enable bit 3 Serial I/O1 transmit/SCL, SDA interrupt enable bit 4 Timer X interrupt enable bit 5 Timer Y interrupt enable bit 6 Timer 1 interrupt enable bit 7 Timer 2 interrupt enable bit
0 0 0 0
Fig. 2.2.6 Structure of Interrupt control register 1
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-10
APPLICATION 3804 Group (Spec.H) 2.2 Interrupt
Interrupt control register 2
b7 b6 b5 b4 b3 b2 b1 b0
0
Interrupt control register 2 (ICON2 : address 003F16)
b
Name
Functions
0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled
At reset R W
0 0
0 CNTR0/SCL, SDA interrupt enable bit 1 CNTR1/ Serial I/O3 receive interrupt enable bit 2 Serial I/O2/ Timer Z interrupt enable bit 3 INT2/I2C interrupt enable bit 4 INT3 interrupt enable bit 5 INT4/CNTR2 interrupt enable bit 6 AD converter/Serial I/O3 transmit interrupt enable bit 7 Fix this bit to "0".
0 0 0 0 0
0
Fig. 2.2.7 Structure of Interrupt control register 2
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-11
APPLICATION 3804 Group (Spec.H) 2.2 Interrupt
2.2.3 Interrupt source The 3804 group (Spec. H) 's interrupts are a type of vector and occur by 16 sources among 23 sources: nine external, thirteen internal, and one software. These are vector interrupts with a fixed priority system. Accordingly, when two or more interrupt requests occur during the same sampling, the higher-priority interrupt is accepted first. This priority is determined by hardware, but a variety of priority processing can be performed by software, using an interrupt enable bit and an interrupt disable flag. For interrupt sources, vector addresses and interrupt priority, refer to Tables 2.2.1.
Table 2.2.1 Interrupt sources, vector addresses and priority Interrupt Source Reset (Note 2) INT0 Timer Z INT1 Serial I/O1 reception Serial I/O1 transmission SCL, SDA Timer X Timer Y Timer 1 Timer 2 CNTR0 SCL, SDA CNTR1 Serial I/O3 reception Serial I/O2 Timer Z INT2 I 2C INT3 INT4 CNTR2 A/D converter Serial I/O3 transmission BRK instruction 16 FFDF16 FFDE16 11 FFE916 FFE816 6 7 8 9 10 FFF316 FFF116 FFEF16 FFED16 FFEB16 FFF216 FFF016 FFEE16 FFEC16 FFEA16 Priority 1 2 Vector Addresses (Note 1) Low High FFFC16 FFFD16 FFFB16 FFFA16 Interrupt Request Generating Conditions At reset At detection of either rising or falling edge of INT0 input At timer Z underflow At detection of either rising or falling edge of INT1 input At completion of serial I/O1 data reception At completion of serial I/O1 transmission shift or when transmission buffer is empty At detection of either rising or falling edge of SCL or SDA At timer X underflow At timer Y underflow At timer 1 underflow At timer 2 underflow At detection of either rising or falling edge of CNTR0 input At detection of either rising or falling edge of SCL or SDA At detection of either rising or falling edge of CNTR1 input At completion of serial I/O3 data reception At completion of serial I/O2 data transmission or reception At timer Z underflow 13 FFE516 FFE416 At detection of either rising or falling edge of INT2 input At completion of data transfer 14 15 FFE316 FFE116 FFE216 FFE016 At detection of either rising or falling edge of INT3 input At detection of either rising or falling edge of INT4 input At detection of either rising or falling edge of CNTR2 input At completion of A/D conversion At completion of serial I/O3 transmission shift or when transmission buffer is empty 17 FFDD16 FFDC16 At BRK instruction execution Valid when serial I/O3 is selected External interrupt (active edge selectable) External interrupt (active edge selectable) External interrupt (active edge selectable) External interrupt (active edge selectable) External interrupt (active edge selectable) External interrupt (active edge selectable) External interrupt (active edge selectable) Valid when serial I/O3 is selected Valid when serial I/O2 is selected STP release timer underflow Remarks Non-maskable External interrupt (active edge selectable) External interrupt (active edge selectable) Valid when serial I/O1 is selected Valid when serial I/O1 is selected
3 4 5
FFF916 FFF716 FFF516
FFF816 FFF616 FFF416
External interrupt (active edge selectable)
12
FFE716
FFE616
Non-maskable software interrupt
Notes 1: Vector addresses contain interrupt jump destination addresses. 2: Reset function in the same way as an interrupt with the highest priority.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-12
APPLICATION 3804 Group (Spec.H) 2.2 Interrupt
2.2.4 Interrupt operation When an interrupt request is accepted, the contents of the following registers just before acceptance of the interrupt requests are automatically pushed onto the stack area in the order of , and . High-order contents of program counter (PCH) Low-order contents of program counter (PCL) Contents of processor status register (PS) After the contents of the above registers are pushed onto the stack area, the accepted interrupt vector address enters the program counter and consequently the interrupt processing routine is executed. When the RTI instruction is executed at the end of the interrupt processing routine, the contents of the above registers pushed onto the stack area are restored to the respective registers in the order of , and ; and the microcomputer resumes the processing executed just before acceptance of the interrupts. Figure 2.2.8 shows an interrupt operation diagram.
Executing routine ******* Interrupt occurs (Accepting interrupt request)
Suspended operation
Contents of program counter (high-order) are pushed onto stack Contents of program counter (low-order) are pushed onto stack Contents of processor status register are pushed onto stack Interrupt processing routine RTI instruction Contents of processor status register are popped from stack Contents of program counter (low-order) are popped from stack Contents of program counter (high-order) are popped from stack
Resume processing *******
: Operation commanded by software : Internal operation performed automatically
Fig. 2.2.8 Interrupt operation diagram
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-13
APPLICATION 3804 Group (Spec.H) 2.2 Interrupt
(1) Processing upon acceptance of interrupt request Upon acceptance of an interrupt request, the following operations are automatically performed. The processing being executed is stopped. The contents of the program counter and the processor status register are pushed onto the stack area. Figure 2.2.9 shows the changes of the stack pointer and the program counter upon acceptance of an interrupt request. Concurrently with the push operation, the jump destination address (the beginning address of the interrupt processing routine) of the occurring interrupt stored in the vector address is set in the program counter, then the interrupt processing routine is executed. After the interrupt processing routine is started, the corresponding interrupt request bit is automatically cleared to "0". The interrupt disable flag is set to "1" so that multiple interrupts are disabled. Accordingly, for executing the interrupt processing routine, it is necessary to set the jump destination address in the vector area corresponding to each interrupt.
Program counter PCL Program counter (low-order) PCH Program counter (high-order) Stack pointer S (S) Interrupt request is accepted Program counter PCL PCH Vector address (from Interrupt vector area) Stack pointer S (S) - 3 Interrupt disable flag = "1" (s) - 3 Interrupt disable flag = "0" (S)
Stack area
Stack area
Processor status register Program counter (low-order) (S) Program counter (high-order)
Fig. 2.2.9 Changes of stack pointer and program counter upon acceptance of interrupt request
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-14
APPLICATION 3804 Group (Spec.H) 2.2 Interrupt
(2) Timing after acceptance of interrupt request The interrupt processing routine begins with the machine cycle following the completion of the instruction that is currently being executed. Figure 2.2.10 shows the time up to execution of interrupt processing routine and Figure 2.2.11 shows the timing chart after acceptance of interrupt request.
Interrupt request generated
Start of interrupt processing
Main routine
Waiting time for Stack push and post-processing Vector fetch of pipeline
Interrupt processing routine
0 to 16 cycles
2 cycles
5 cycles
7 to 23 cycles (When f(XIN) = 8 MHz, 1.75 s to 5.75 s) When executing DIV instruction
Fig. 2.2.10 Time up to execution of interrupt processing routine
Waiting time for pipeline post-processing
Push onto stack Vector fetch
Interrupt operation starts
SYNC RD WR Address bus Data bus PC Not used
S, SPS S-1, SPS S-2, SPS
BL AL
BH
AL, AH AH
PCH
PCL
PS
SYNC : CPU operation code fetch cycle (This is an internal signal that cannot be observed from the external unit.) BL, BH : Vector address of each interrupt AL, AH : Jump destination address of each interrupt SPS : "0016" or "0116"
Fig. 2.2.11 Timing chart after acceptance of interrupt request
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-15
APPLICATION 3804 Group (Spec.H) 2.2 Interrupt
2.2.5 Interrupt control The acceptance of all interrupts, excluding the BRK instruction interrupt, can be controlled by the interrupt request bit, interrupt enable bit, and an interrupt disable flag, as described in detail below. Figure 2.2.12 shows an interrupt control diagram.
Interrupt request bit Interrupt enable bit Interrupt request Interrupt disable flag BRK instruction Reset
Fig. 2.2.12 Interrupt control diagram The interrupt request bit, interrupt enable bit and interrupt disable flag function independently and do not affect each other. An interrupt is accepted when all the following conditions are satisfied. qInterrupt request bit .......... "1" qInterrupt enable bit ........... "1" qInterrupt disable flag ........ "0" Though the interrupt priority is determined by hardware, a variety of priority processing can be performed by software using the above bits and flag. Tables 2.2.2 shows list of interrupt control bits according to the interrupt source. (1) Interrupt request bits The interrupt request bits are allocated to the interrupt request register 1 (address 003C16) and interrupt request register 2 (address 003D16). The occurrence of an interrupt request causes the corresponding interrupt request bit to be set to "1". The interrupt request bit is held in the "1" state until the interrupt is accepted. When the interrupt is accepted, this bit is automatically cleared to "0". Each interrupt request bit can be set to "0", but cannot be set to "1", by software. (2) Interrupt enable bits The interrupt enable bits are allocated to the interrupt control register 1 (address 003E16) and the interrupt control register 2 (address 003F16). The interrupt enable bits control the acceptance of the corresponding interrupt request. When an interrupt enable bit is "0", the corresponding interrupt request is disabled. If an interrupt request occurs when this bit is "0", the corresponding interrupt request bit is set to "1" but the interrupt is not accepted. In this case, unless the interrupt request bit is set to "0" by software, the interrupt request bit remains in the "1" state. When an interrupt enable bit is "1", the corresponding interrupt is enabled. If an interrupt request occurs when this bit is "1", the interrupt is accepted (when interrupt disable flag = "0"). Each interrupt enable bit can be set to "0" or "1" by software.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-16
APPLICATION 3804 Group (Spec.H) 2.2 Interrupt
(3) Interrupt disable flag The interrupt disable flag is allocated to bit 2 of the processor status register. The interrupt disable flag controls the acceptance of interrupt request except BRK instruction. When this flag is "1", the acceptance of interrupt requests is disabled. When the flag is "0", the acceptance of interrupt requests is enabled. This flag is set to "1" with the SEI instruction and is set to "0" with the CLI instruction. When a main routine branches to an interrupt processing routine, this flag is automatically set to "1", so that multiple interrupts are disabled. To use multiple interrupts, set this flag to "0" with the CLI instruction within the interrupt processing routine. Figure 2.2.13 shows an example of multiple interrupts. Table 2.2.2 List of interrupt bits according to interrupt source Interrupt source INT0/Timer Z INT1 Serial I/O1 reception Serial I/O1 transmission/SCL, SDA Timer X Timer Y Timer 1 Timer 2 CNTR0/SCL, SDA CNTR1/Serial I/O3 reception Serial I/O2/Timer Z INT2/I2C INT3 INT4/CNTR2 A/D converter/Serial I/O3 transmission Interrupt enable bit Address 003E16 003E16 003E16 003E16 003E16 003E16 003E16 003E16 003F16 003F16 003F16 003F16 003F16 003F16 003F16 Bit b0 b1 b2 b3 b4 b5 b6 b7 b0 b1 b2 b3 b4 b5 b6 Interrupt request bit Address 003C16 003C16 003C16 003C16 003C16 003C16 003C16 003C16 003D16 003D16 003D16 003D16 003D16 003D16 003D16 Bit b0 b1 b2 b3 b4 b5 b6 b7 b0 b1 b2 b3 b4 b5 b6
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-17
APPLICATION 3804 Group (Spec.H) 2.2 Interrupt
Interrupt request
Nesting Reset
Time
Main routine I=1 C1 = 0, C2 = 0 Interrupt request 1 C1 = 1 I=0 Interrupt 1 Interrupt request 2 I=1 C2 = 1 I=0 Interrupt 2 I=1 RTI I=0 Multiple interrupt
RTI I=0
I : Interrupt disable flag C1 : Interrupt enable bit of interrupt 1 C2 : Interrupt enable bit of interrupt 2 : Set automatically. : Set by software.
Fig. 2.2.13 Example of multiple interrupts
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-18
APPLICATION 3804 Group (Spec.H) 2.2 Interrupt
2.2.6 INT interrupt The INT interrupt requests is generated when the microcomputer detects a level change of each INT pin (INT0-INT4). (1) Active edge selection INT0-INT4 can be selected from either a falling edge or rising edge detection as an active edge by the interrupt edge selection register. In the "0" state, the falling edge of the corresponding pin is detected. In the "1" state, the rising edge of the corresponding pin is detected. (2) INT0, INT2, INT4 interrupt source selection When using the following interrupt source, select which of the interrupt source by the interrupt source selection register (address 003916). (Set these bits to "0" when using INT.) *INT0 or timer Z (bit 0) *INT4 or CNTR2 (bit 4) *INT2 or I 2C (bit 5)
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-19
APPLICATION 3804 Group (Spec.H) 2.2 Interrupt
2.2.7 Notes on interrupts (1) Change of relevant register settings When the setting of the following registers or bits is changed, the interrupt request bit may be set to "1". When not requiring the interrupt occurrence synchronized with these setting, take the following sequence. *Interrupt edge selection register (address 003A16) *Timer XY mode register (address 002316) *Timer Z mode register (address 002A16) *I2C START/STOP condition control register (address 001616) Set the above listed registers or bits as the following sequence.
Set the corresponding interrupt enable bit to "0" (disabled) . Set the interrupt edge select bit (active edge switch bit) or the interrupt (source) select bit to "1". NOP (One or more instructions) Set the corresponding interrupt request bit to "0" (no interrupt request issued). Set the corresponding interrupt enable bit to "1" (enabled).
Fig. 2.2.14 Sequence of changing relevant register s Reason When setting the followings, the interrupt request bit may be set to "1". *When setting external interrupt active edge Concerned register: Interrupt edge selection register (address 003A16) Timer XY mode register (address 002316) Timer Z mode register (address 002A16) I 2C START/STOP condition control register (address 001616) *When switching interrupt sources of an interrupt vector address where two or more interrupt sources are allocated. Concerned register: Interrupt source selection register (address 003916)
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-20
APPLICATION 3804 Group (Spec.H) 2.2 Interrupt
(2) Check of interrupt request bit q When executing the BBC or BBS instruction to an interrupt request bit of an interrupt request register immediately after this bit is set to "0", execute one or more instructions before executing the BBC or BBS instruction.
Clear the interrupt request bit to "0" (no interrupt issued) NOP (one or more instructions) Execute the BBC or BBS instruction
Fig. 2.2.15 Sequence of check of interrupt request bit s Reason If the BBC or BBS instruction is executed immediately after an interrupt request bit of an interrupt request register is cleared to "0", the value of the interrupt request bit before being cleared to "0" is read.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-21
APPLICATION 3804 Group (Spec.H) 2.3 Timer
2.3 Timer
This paragraph explains the registers setting method and the notes relevant to the timers. 2.3.1 Memory map
Address 000E16 000F16 002016 002116 002216 002316 002416 002516 002616 002716 002816 002916 002A16
Timer 12, X count source selection register (T12XCSS) Timer Y, Z count source selection register (TYZCSS)
Prescaler 12 (PRE12) Timer 1 (T1) Timer 2 (T2) Timer XY mode register (TM) Prescaler X (PREX) Timer X (TX) Prescaler Y (PREY) Timer Y (TY) Timer Z low-order (TZL) Timer Z high-order (TZH) Timer Z mode register (TZM)
003916 003C16 003D16 003E16 003F16
Interrupt source selection register (INTSEL)
Interrupt request register 1 (IREQ1) Interrupt request register 2 (IREQ2) Interrupt control register 1 (ICON1) Interrupt control register 2 (ICON2)
Fig. 2.3.1 Memory map of registers relevant to timers
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-22
APPLICATION 3804 Group (Spec.H) 2.3 Timer
2.3.2 Relevant registers
Prescaler 12, Prescaler X, Prescaler Y
b7 b6 b5 b4 b3 b2 b1 b0 Prescaler 12 (PRE12), Prescaler X (PREX), Prescaler Y (PREY) (addresses 002016, 002416, 002616)
b
Functions
At reset R W
1 1 1 1 1 1 1 1
0 * Set a count value of each prescaler. 1 * The value set in this register is written to both 2 each prescaler and the corresponding 3 prescaler latch at the same time. * When this register is read out, the count value 4 of the corresponding prescaler is read out. 5 6 7
Fig. 2.3.2 Structure of Prescaler 12, Prescaler X, Prescaler Y
Timer 1
b7 b6 b5 b4 b3 b2 b1 b0 Timer 1 (T1: address 002116)
b
Functions
At reset R W
1 0 0 0 0 0 0 0
0 * Set timer 1 count value. 1 * The value set in this register is written to both 2 the timer 1 and the timer 1 latch at the same 3 time. * When the timer 1 is read out, the count value 4 of the timer 1 is read out. 5 6 7
Fig. 2.3.3 Structure of Timer 1
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-23
APPLICATION 3804 Group (Spec.H) 2.3 Timer
Timer 2, Timer X, Timer Y
b7 b6 b5 b4 b3 b2 b1 b0 Timer 2 (T2), Timer X (TX), Timer Y (TY) (addresses 002216, 002516, 002716)
b
Functions
At reset R W
1 1 1 1 1 1 1 1
0 * Set each timer count value. 1 * The value set in this register is written to both 2 each timer and the corresponding timer latch 3 at the same time. * When each timer is read out, the count value 4 of the corresponding timer is read out. 5 6 7
Fig. 2.3.4 Structure of Timer 2, Timer X, Timer Y
Timer Z low-order, Timer Z high-order
b7 b6 b5 b4 b3 b2 b1 b0 Timer Z low-order (TZL), Timer Z high-order (TZH) (addresses 002816, 002916)
b
0 1 2 3 4 5 6 7
Functions
* Set each timer count value. [At write] * Depending on the write control bit (bit 3 of TZM), the value set to this register is written to each timer and the corresponding timer latch at the same time, or is written only to the latch. [At read] * The corresponding timer count value is read out by reading this register. * Read both registers in order of TZH and TZL following. * Write both registers in order of TZL and TZH following.
At reset R W
1 1 1 1 1 1 1 1
Fig. 2.3.5 Structure of Timer Z (low-order, high-order)
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-24
APPLICATION 3804 Group (Spec.H) 2.3 Timer
Timer XY mode register
b7 b6 b5 b4 b3 b2 b1 b0 Timer XY mode register (TM: address 002316)
b
Name
b1 b0
Functions
At reset R W
0 0 0 0 0 0 0 0
0 Timer X operating mode bits 1 2 3 4 5 6 7
0 0: Timer mode 0 1: Pulse output mode 1 0: Event counter mode 1 1: Pulse width measurement mode CNTR0 active edge Refer to Table 2.3.1 switch bit Timer X count stop 0: Count start 1: Count stop bit Timer Y operating b5 b4 0 0: Timer mode mode bits 0 1: Pulse output mode 1 0: Event counter mode 1 1: Pulse width measurement mode CNTR1 active edge Refer to Table 2.3.1 switch bit Timer Y count stop 0: Count start 1: Count stop bit
Fig. 2.3.6 Structure of Timer XY mode register Table 2.3.1 CNTR0 /CNTR1 active edge switch bit function Timer X /Timer Y operation modes Timer mode CNTR0 / CNTR1 active edge switch bit (bits 2, 6 of address 002316) contents "0" CNTR0 / CNTR1 interrupt request occurrence: Falling edge ; No influence to timer count "1" CNTR0 / CNTR1 interrupt request occurrence: Rising edge Pulse output mode ; No influence to timer count "0" Pulse output start: Beginning at "H" level CNTR0 / CNTR1 interrupt request occurrence: Falling edge "1" Pulse output start: Beginning at "L" level CNTR0 / CNTR1 interrupt request occurrence: Rising edge Event counter mode "0" Timer X / Timer Y: Rising edge count CNTR0 / CNTR1 interrupt request occurrence: Falling edge "1" Timer X / Timer Y: Falling edge count CNTR0 / CNTR1 interrupt request occurrence: Rising edge Pulse width measurement mode "0" Timer X / Timer Y: "H" level width measurement CNTR0 / CNTR1 interrupt request occurrence: Falling edge "1" Timer X / Timer Y: "L" level width measurement CNTR0 / CNTR1 interrupt request occurrence: Rising edge
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-25
APPLICATION 3804 Group (Spec.H) 2.3 Timer
Timer Z mode register
b7 b6 b5 b4 b3 b2 b1 b0 Timer Z mode register (TZM: address 002A16)
b
Name
b2b1b0
Functions
0 0 0: Timer/Event counter mode 0 0 1: Pulse output mode 0 1 0: Pulse period measurement mode 0 1 1: Pulse width measurement mode 1 0 0: Programmable waveform generating mode 1 0 1: Programmable one-shot generating mode 1 1 0: Not available 1 1 1: Not available
At reset R W
0
0 Timer Z operating mode bits 1
0
2
0
3 Timer Z write control 0: Writing data to both latch and timer simultaneousuly bit 1: Writing data only to latch 0: "L" output 4 Output level latch 1: "H" output CNTR2 active edge Refer to Table 2.3.2. 5 switch bit 6 Timer Z count stop 0: Count start 1: Count stop bit 7 Timer/Event counter 0: Timer mode mode switch bit (Note) 1: Event counter mode
0
0 0 0 0
Note: When selecting the modes except the timer/event counter mode, set "0" to this bit.
Fig. 2.3.7 Structure of Timer Z mode register
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-26
APPLICATION 3804 Group (Spec.H) 2.3 Timer
Table 2.3.2 CNTR2 active edge switch bit function Timer Z operation modes Timer mode CNTR2 active edge switch bit (bit 5 of address 002A16) contents "0" CNTR2 interrupt request occurrence: Falling edge ; No influence to timer count "1" CNTR2 interrupt request occurrence: Rising edge ; No influence to timer count Event counter mode "0" Timer Z: Rising edge count CNTR2 interrupt request occurrence: Falling edge "1" Timer Z: Falling edge count CNTR2 interrupt request occurrence: Rising edge Pulse output mode "0" Pulse output start: Beginning at "H" level CNTR2 interrupt request occurrence: Falling edge "1" Pulse output start: Beginning at "L" level CNTR2 interrupt request occurrence: Rising edge Pulse period measurement mode "0" Timer Z : Term from one falling edge to next falling edge measurement CNTR2 interrupt request occurrence: Falling edge "1" Timer Z : Term from one rising edge to next rising edge measurement CNTR2 interrupt request occurrence: Rising edge Pulse width measurement mode "0" Timer Z: "H" level width measurement CNTR2 interrupt request occurrence: Falling edge "1" Timer Z: "L" level width measurement CNTR2 interrupt request occurrence: Rising edge Programmable one-shot generating "0" Timer Z : Pulse output start from "L" level, and "H" level one-shot mode pulse is output. CNTR2 interrupt request occurrence: Falling edge "1" Timer Z : Pulse output start from "H" level, and "L" level one-shot pulse is output. CNTR2 interrupt request occurrence: Rising edge
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-27
APPLICATION 3804 Group (Spec.H) 2.3 Timer
Timer 12, X count source selection register
b7 b6 b5 b4 b3 b2 b1 b0 Timer 12, X count source selection register (T12XCSS: address 000E16)
b
Name
b3b2b1b0
Functions
0 0 0 0: f(XIN)/2 or f(XCIN)/2 0 0 0 1: f(XIN)/4 or f(XCIN)/4 0 0 1 0: f(XIN)/8 or f(XCIN)/8 0 0 1 1: f(XIN)/16 or f(XCIN)/16 0 1 0 0: f(XIN)/32 or f(XCIN)/32 0 1 0 1: f(XIN)/64 or f(XCIN)/64 0 1 1 0: f(XIN)/128 or f(XCIN)/128 0 1 1 1: f(XIN)/256 or f(XCIN)/256 1 0 0 0: f(XIN)/512 or f(XCIN)/512 1 0 0 1: f(XIN)/1024 or f(XCIN)/1024 1010 to 1111: Not available
b7b6b5b4
At reset R W
1 1 0 0 1 1 0 0
0 Timer 12 count source selection bits 1 2 3 4 Timer X count source selection bits 5 6 7
0 0 0 0: f(XIN)/2 or f(XCIN)/2 0 0 0 1: f(XIN)/4 or f(XCIN)/4 0 0 1 0: f(XIN)/8 or f(XCIN)/8 0 0 1 1: f(XIN)/16 or f(XCIN)/16 0 1 0 0: f(XIN)/32 or f(XCIN)/32 0 1 0 1: f(XIN)/64 or f(XCIN)/64 0 1 1 0: f(XIN)/128 or f(XCIN)/128 0 1 1 1: f(XIN)/256 or f(XCIN)/256 1 0 0 0: f(XIN)/512 or f(XCIN)/512 1 0 0 1: f(XIN)/1024 or f(XCIN)/1024 1 0 1 0: f(XCIN) 1011 to 1111: Not available
Fig. 2.3.8 Structure of Timer 12, X count source selection register
Timer Y, Z count source selection register
b7 b6 b5 b4 b3 b2 b1 b0 Timer Y, Z count source selection register (TYZCSS: address 000F16)
b
Name
b3b2b1b0
Functions
0 0 0 0: f(XIN)/2 or f(XCIN)/2 0 0 0 1: f(XIN)/4 or f(XCIN)/4 0 0 1 0: f(XIN)/8 or f(XCIN)/8 0 0 1 1: f(XIN)/16 or f(XCIN)/16 0 1 0 0: f(XIN)/32 or f(XCIN)/32 0 1 0 1: f(XIN)/64 or f(XCIN)/64 0 1 1 0: f(XIN)/128 or f(XCIN)/128 0 1 1 1: f(XIN)/256 or f(XCIN)/256 1 0 0 0: f(XIN)/512 or f(XCIN)/512 1 0 0 1: f(XIN)/1024 or f(XCIN)/1024 1 0 1 0: f(XCIN) 1011 to 1111: Not available
b7b6b5b4
At reset R W
1
0 Timer Y count source selection bits 1
1 0
2 3
0
4 Timer Z count source selection bits 5
6
7
0 0 0 0: f(XIN)/2 or f(XCIN)/2 0 0 0 1: f(XIN)/4 or f(XCIN)/4 0 0 1 0: f(XIN)/8 or f(XCIN)/8 0 0 1 1: f(XIN)/16 or f(XCIN)/16 0 1 0 0: f(XIN)/32 or f(XCIN)/32 0 1 0 1: f(XIN)/64 or f(XCIN)/64 0 1 1 0: f(XIN)/128 or f(XCIN)/128 0 1 1 1: f(XIN)/256 or f(XCIN)/256 1 0 0 0: f(XIN)/512 or f(XCIN)/512 1 0 0 1: f(XIN)/1024 or f(XCIN)/1024 1 0 1 0: f(XCIN) 1011 to 1111: Not available
1
1
0
0
Fig. 2.3.9 Structure of Timer Y, Z count source selection register
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-28
APPLICATION 3804 Group (Spec.H) 2.3 Timer
Interrupt source selection register
b7 b6 b5 b4 b3 b2 b1 b0 Interrupt source selection register (INTSEL: address 003916)
b
Name
Functions
0: INT0 interrupt 1: Timer Z interrupt 0: Serial I/O2 interrupt 1: Timer Z interrupt 0: Serial I/O1 transmit interrupt 1: SCL, SDA interrupt 0: CNTR0 interrupt 1: SCL, SDA interrupt 0: INT4 interrupt 1: CNTR2 interrupt 0: INT2 interrupt 1: I2C interrupt 0: CNTR1 interrupt 1: Serial I/O3 receive interrupt 0: A/D converter interrupt 1: Serial I/O3 transmit interrupt
At reset R W
0
0 INT0/Timer Z interrupt source selection bit (*1) 1 Serial I/O2/Timer Z interrupt source selection bit (*1) 2 Serial I/O1 transmit/ SCL, SDA interrupt source selection bit (*2) 3 CNTR0/SCL, SDA interrupt source selection bit (*2) 4 INT4/CNTR2 interrupt source selection bit 5 INT2/I2C interrupt source selection bit 6 CNTR1/Serial I/O3 receive interrupt source selection bit 7 AD converter/Serial I/O3 transmit interrupt source selection bit
0
0
0
0
0 0
0
*1: Do not write 1 to these bits simultaneously. *2: Do not write 1 to these bits simultaneously.
Fig. 2.3.10 Structure of Interrupt source selection register
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-29
APPLICATION 3804 Group (Spec.H) 2.3 Timer
Interrupt request register 1
b7 b6 b5 b4 b3 b2 b1 b0 Interrupt request register 1 (IREQ1 : address 003C16)
b
Name
Functions
At reset R W
0 0 0 0
0 INT0/Timer Z 0 : No interrupt request issued interrupt request bit 1 : Interrupt request issued 1 INT1 interrupt request bit
0 : No interrupt request issued
1 : Interrupt request issued
2 Serial I/O1 receive 0 : No interrupt request issued interrupt request bit 1 : Interrupt request issued
0 : No interrupt request issued 3 Serial I/O1 transmit/SCL, SDA 1 : Interrupt request issued interrupt request bit
4 Timer X interrupt request bit 5 Timer Y interrupt request bit 6 Timer 1 interrupt request bit
0 : No interrupt request issued
0 0 0 0

1 : Interrupt request issued
0 : No interrupt request issued
1 : Interrupt request issued
0 : No interrupt request issued
1 : Interrupt request issued
7 Timer 2 interrupt 0 : No interrupt request issued request bit 1 : Interrupt request issued : 0 can be set by software, but 1 cannot be set.
Fig. 2.3.11 Structure of Interrupt request register 1
Interrupt request register 2
b7 b6 b5 b4 b3 b2 b1 b0 Interrupt request register 2 (IREQ2 : address 003D16)
b
Name
Functions
0 : No interrupt request issued 1 : Interrupt request issued 0 : No interrupt request issued 1 : Interrupt request issued 0 : No interrupt request issued 1 : Interrupt request issued 0 : No interrupt request issued 1 : Interrupt request issued 0 : No interrupt request issued 1 : Interrupt request issued 0 : No interrupt request issued 1 : Interrupt request issued 0 : No interrupt request issued 1 : Interrupt request issued
At reset R W
0 0
0 CNTR0/SCL, SDA interrupt request bit 1 CNTR1/Serial I/O3 receive interrupt request bit 2 Serial I/O2/Timer Z interrupt request bit 3 INT2/I2C interrupt request bit 4 INT3 interrupt request bit 5 INT4/CNTR2 interrupt request bit 6 AD converter/Serial I/O3 transmit interrupt request bit
0 0 0 0 0

7 Nothing is arranged for this bit. This is a write disabled bit. When this bit is read out, the contents are 0 . : 0 can be set by software, but 1 cannot be set.
0
Fig. 2.3.12 Structure of Interrupt request register 2
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-30
APPLICATION 3804 Group (Spec.H) 2.3 Timer
Interrupt control register 1
b7 b6 b5 b4 b3 b2 b1 b0 Interrupt control register 1 (ICON1 : address 003E16)
b
Name
Functions
0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled
At reset R W
0 0 0 0
0 INT0/Timer Z interrupt enable bit 1 INT1 interrupt enable bit 2 Serial I/O1 receive interrupt enable bit 3 Serial I/O1 transmit/SCL, SDA interrupt enable bit 4 Timer X interrupt enable bit 5 Timer Y interrupt enable bit 6 Timer 1 interrupt enable bit Timer 2 interrupt 7 enable bit
0 0 0 0
Fig. 2.3.13 Structure of Interrupt control register 1
Interrupt control register 2
b7 b6 b5 b4 b3 b2 b1 b0
0
Interrupt control register 2 (ICON2 : address 003F16)
b
Name
Functions
0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled
At reset R W
0 0
0 CNTR0/SCL, SDA interrupt enable bit 1 CNTR1/ Serial I/O3 receive interrupt enable bit 2 Serial I/O2/ Timer Z interrupt enable bit 3 INT2/I2C interrupt enable bit 4 INT3 interrupt enable bit 5 INT4/CNTR2 interrupt enable bit 6 AD converter/Serial I/O3 transmit interrupt enable bit 7 Fix this bit to "0".
0 0 0 0 0
0
Fig. 2.3.14 Structure of Interrupt control register 2
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-31
APPLICATION 3804 Group (Spec.H) 2.3 Timer
2.3.3 Timer application examples (1) Basic functions and uses [Function 1] Control of Event interval (Timer X, Timer Y, Timer Z, Timer 1, Timer 2) When a certain time, by setting a count value to each timer, has passed, the timer interrupt request occurs. *Generation of an output signal timing *Generation of a wait time [Function 2] Control of Cyclic operation (Timer X, Timer Y, Timer Z, Timer 1, Timer 2) The value of the timer latch is automatically written to the corresponding timer each time the timer underflows, and each timer interrupt request occurs in cycles. *Generation of cyclic interrupts *Clock function (measurement of 250 ms); see Application example 1 *Control of a main routine cycle [Function 3] Output of Rectangular waveform (Timer X, Timer Y, Timer Z) The output level of the CNTR pin is inverted each time the timer underflows (in the pulse output mode). *Piezoelectric buzzer output; see Application example 2 *Generation of the remote control carrier waveforms [Function 4] Count of External pulses (Timer X, Timer Y, Timer Z) External pulses input to the CNTR pin are counted as the timer count source (in the event counter mode). *Frequency measurement; see Application example 3 *Division of external pulses *Generation of interrupts due to a cycle using external pulses as the count source; count of a reel pulse [Function 5] Measurement of External pulse width (Timer X, Timer Y, Timer Z) The "H" or "L" level width of external pulses input to CNTR pin is measured (in the pulse width measurement mode). *Measurement of external pulse frequency (measurement of pulse width of FG pulse for a motor); see Application example 4 *Measurement of external pulse duty (when the frequency is fixed) FG pulse : Pulse used for detecting the motor speed to control the motor speed. [Function 6] Output of Arbitrary waveform (Timer Z) The value which is set to the output level latch is output from the CNTR pin each time the timer underflows. (programmable waveform generating mode) [Function 7] One-shot pulse output by external trigger (Timer Z) The value of timer latch is set to timer by trigger signal which is input from the INT pin, and timer is counted down. When trigger signal is input, "H" or "L" is output from the CNTR pin at the same time, and "L" or "H" is output by underflow of timer. (programmable one-shot generating mode)
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-32
APPLICATION 3804 Group (Spec.H) 2.3 Timer
(2) Timer application example 1: Clock function (measurement of 250 ms) Outline: The input clock is divided by the timer so that the clock can count up at 250 ms intervals. Specifications: *The clock f(XIN) = 4.19 MHz (2 22 Hz) is divided by the timer. *The clock is counted up in the process routine of the timer X interrupt which occurs at 250 ms intervals. Figure 2.3.15 shows the timers connection and setting of division ratios; Figure 2.3.16 shows the relevant registers setting; Figure 2.3.17 shows the control procedure.
Timer X count source selection bit f(XIN) = 4.19 MHz 1/16
Prescaler X 1/256
Timer X 1/256
Timer X interrupt request bit 0 or 1 250 ms
Dividing by 4 with software
1/4 1 second
0 : No interrupt request issued 1 : Interrupt request issued
Fig. 2.3.15 Timers connection and setting of division ratios
Timer 12, X count source selection register (address 000E16)
b7 b0
T12XCSS
0011 Timer X count source : f(XIN)/16
Timer XY mode register (address 002316)
b7 b0
TM
1
00 Timer X operating mode: Timer mode Timer X count: Stop Clear to "0" when starting count.
Prescaler X (address 002416)
b7 b0
PREX
256 - 1
Timer X (address 002516)
b7 b0
Set "division ratio - 1"
TX
256 - 1
Interrupt control register 1 (address 003E16)
b7 b0
ICON1
1 Timer X interrupt: Enabled
Interrupt request register 1 (address 003C16)
b7 b0
IREQ1
0 Timer X interrupt request (becomes "1" at 250 ms intervals)
Fig. 2.3.16 Relevant registers setting
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-33
APPLICATION 3804 Group (Spec.H) 2.3 Timer
RESET
q x: This bit is not used here. Set it to "0" or "1" arbitrarily.
Initialization SEI TM XXXX1X002 (address 002316) IREQ1 (address 003C16), bit4 0 ICON1 (address 003E16), bit4 1
..... .....
*All interrupts disabled *Timer X : Timer mode *Clear Timer X interrupt request bit *Timer X interrupt enabled
T12XCSS (address 000E16) (address 002416) PREX (address 002516) TX TM CLI
..... .....
0011XXXX2 256 - 1 256 - 1 0
*Timer X count source : f(XIN)/16 *Set "division ratio - 1" to Prescaler X and Timer X
(address 002316), bit3
*Timer X count start *Interrupts enabled
Main processing (Note 1) PREX (address 002416) 256 - 1 TX (address 002516) 256 - 1 IREQ1 (address 003C16), bit4 0
.....
*Reset Timer to restart count from 0 second after completion of clock set Note 1: Perform procedure for completion of clock set only when completing clock set.
Timer X interrupt process routine
CLT (Note 2) CLD (Note 3) Push registers to stack
Note 2: When using Index X mode flag (T) Note 3: When using Decimal mode flag (D) *Push registers used in interrupt process routine
Clock stop ? N Clock count up (1/4 second to year)
Y
*Judge whether clock stops
*Clock count up
Pop registers
*Pop registers pushed to stack
RTI
Fig. 2.3.17 Control procedure
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-34
APPLICATION 3804 Group (Spec.H) 2.3 Timer
(3) Timer application example 2: Piezoelectric buzzer output Outline: The rectangular waveform output function of the timer is applied for a piezoelectric buzzer output. Specifications: *The rectangular waveform, dividing the clock f(XIN) = 8 MHz into about 2 kHz (2049 Hz), is output from the P47/CNTR2 pin. *The level of the P47/CNTR2 pin is fixed to "H" while a piezoelectric buzzer output stops. Figure 2.3.18 shows a peripheral circuit example, and Figure 2.3.19 shows the timers connection and setting of division ratios. Figure 2.3.20 shows the relevant registers setting, and Figure 2.3.21 shows the control procedure.
The "H" level is output while a piezoelectric buzzer output stops.
CNTR2 output
P47/CNTR2 244 s 244 s
PiPiPi.....
Set a division ratio so that the underflow output period of the timer Z 3804 Group (Spec. H) can be 244 s.
Fig. 2.3.18 Peripheral circuit example
Timer Z count source selection bit Timer Z f(XIN) = 8 MHz 1/16 1/122 CNTR2
Fig. 2.3.19 Timers connection and setting of division ratios
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-35
APPLICATION 3804 Group (Spec.H) 2.3 Timer
Timer Y, Z count source selection register (address 000F16)
b7 b0
TYZCSS
0011
Timer Z count source: f(XIN)/16
Timer Z mode register (address 002A16)
b7 b0
TM
10
0001
Timer Z operating mode : Pulse output mode Write value in latch and timer at the same time CNTR2 active edge switch : Output starting at "H" level Timer Z count : Stop Clear to "0" when starting count Timer Z high-order (address 002916)
b7 b0
TZH
0
Timer Z low-order (address 002816)
b7 b0
Set "division ratio - 1"
TZL
122-1
Port P4 direction register (address 000916)
b7 b0
P4D
1
P47/CNTR2 : Output mode
Port P4 (address 000816)
b7 b0
P4
1
"H" output at stopping buzzer output
Fig. 2.3.20 Relevant registers setting
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-36
APPLICATION 3804 Group (Spec.H) 2.3 Timer
RESET
q X: This bit is not used here. Set it to "0" or "1" arbitrarily.
Initialization P4 (address 000816), bit7 P4D (address 000916)
ICON1 (address 003E16), bit0 0 X10X00012 (address 002A16) TZM TYZCSS (address 000F16) (address 002816) TZL (address 002916) TZH 0011XXXX2 122-1 0
Main processing
Output unit Buzzer request ? Yes
Stop of piezoelectric buzzer output
Fig. 2.3.21 Control procedure
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
.....
1 1XXXXXXX2 *Timer Z interrupt disabled *Timer Z count stopped; Buzzer output stopped *Timer Z: Pulse output mode *Timer Z count source: f(XIN)/16 *Set (division ratio - 1) to timer Z TZM
..... ..... .....
*Processing buzzer request, generated during main processing, in output unit No (address 002A16), bit6 1 TZM (address 002A16), bit6 0 Start of piezoelectric buzzer output
2-37
APPLICATION 3804 Group (Spec.H) 2.3 Timer
(4) Timer application example 3: Frequency measurement Outline: The following two values are compared to judge whether the frequency is within a valid range. *A value by counting pulses input to P55/CNTR1 pin with the timer. *A reference value Specifications: *The pulse is input to the P55/CNTR1 pin and counted by the timer Y. *The clock f(XIN) = 8 MHz is dividing by the timer 1, and the interrupt request occurs at about 2 ms intervals. *A count value is read out at about 2 ms intervals, the timer 1 interrupt interval. When the count value is 28 to 40, it is judged that the input pulse is valid. *Because the timer is a down-counter, the count value is compared with 227 to 215 (Note). Note: 227 to 215 = {255 (initial value of counter) - 28} to {255 - 40}; 28 to 40 means the number of valid count value. Figure 2.3.22 shows the judgment method of valid/invalid of input pulses; Figure 2.3.23 shows the relevant registers setting; Figure 2.3.24 shows the control procedure.
Input pulse
*****
*****
*****
71.4 s or more (less than 14 kHz)
71.4 s (14 kHz)
50 s (20 kHz)
50 s or less (20 kHz or more)
Invalid 2 ms = 28 counts 71.4 s
Valid 2 ms 50 s
Invalid = 40 counts
Fig. 2.3.22 Judgment method of valid/invalid of input pulses
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-38
APPLICATION 3804 Group (Spec.H) 2.3 Timer
Timer XY mode register (address 002316)
b7 b0
TM
1
110 Timer Y operating mode: Event counter mode CNTR1 active edge switch: Falling edge count Timer Y count: Stop Clear to "0" when starting count
Timer 12, X count source selection register (address 000E16)
b7 b0
T12XCSS
0100 f(XIN)/32: select
Prescaler 12 (address 002016)
b7 b0
PRE12
64 - 1
Timer 1 (address 002116)
b7 b0
T1
8-1
Set "division ratio - 1"
Prescaler Y (address 002616)
b7 b0
PREY
1-1
Timer Y (address 002716)
b7 b0
TY
255
Set 255 just before counting pulses (After a certain time has passed, the number of input pulses is decreased from this value.)
Interrupt control register 1 (address 003E16)
b7 b0
ICON1
10 Timer Y interrupt: Disabled Timer 1 interrupt: Enabled
Interrupt request register 1 (address 003C16)
b7 b0
IREQ1
0 Judgment of Timer Y interrupt request bit ( "1" of this bit when reading the count value indicates the 256 or more pulses input in the condition of Timer Y = 255)
Fig. 2.3.23 Relevant registers setting
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-39
APPLICATION 3804 Group (Spec.H) 2.3 Timer
RESET
Initialization SEI 1110XXXX2 (address 002316) TM T12XCSS(address 000E16) XXXX01002 PRE12 (address 002016) 64 - 1 (address 002116) T1 8-1 (address 002616) PREY 1-1 (address 002716) TY 255 IREQ1 (address 003C16) X00XXXXX2 1 ICON1 (address 003E16), bit6 TM CLI
... .. ... .. ... ..
q x: This bit is not used here. Set it to "0" or "1" arbitrary. *All interrupts disabled *Timer Y operating mode : Event counter mode (Count a falling edge of pulses input from CNTR1 pin.) *Set division ratio so that Timer 1 interrupt will occur at 2 ms intervals. *Timer 1, Y interrupt request bit cleared *Timer 1 interrupt: Enabled *Timer Y count start *Interrupts enabled
(address 002316), bit7
0
Timer 1 interrupt process routine
CLT (Note 1) CLD (Note 2) Push registers to stack
Note 1: When using Index X mode flag (T) Note 2: When using Decimal mode flag (D) *Push registers used in interrupt process routine
1 IREQ1(address 003C16), bit5 ? 0 (A) TY (address 002716) *Read the count value *Store the count value into Accumulator (A) *Process as out of range when the count value is 256 or more
In range 214 < (A) < 228 Out of range Fpulse 0 Fpulse
*Compare the read value with reference value *Store the comparison result to flag Fpulse 1
TY (address 002716) IREQ1 (address 003C16), bit5
256 - 1 0
*Initialize the counter value *Clear Timer Y interrupt request bit
Process judgment result
Pop registers
*Pop registers pushed to stack
RTI
Fig. 2.3.24 Control procedure
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-40
APPLICATION 3804 Group (Spec.H) 2.3 Timer
(5) Timer application example 4: Measurement of FG pulse width for motor Outline: The timer Z counts the "H" level width of the pulses input to the P47/CNTR2 pin. An underflow is detected by the timer Z interrupt and an end of the input pulse "H" level is detected by the P47/CNTR2 interrupt. Specifications: *The timer Z counts the "H" level width of the FG pulse input to the P47/CNTR2 pin. When the clock frequency is 8 MHz, the count source is 2 s, which is obtained by dividing the clock frequency by 16. Measurement can be made up to 131.072 ms in the range of FFFF16 to 000016. Figure 2.3.25 shows the timers connection and setting of division ratio; Figure 2.3.26 shows the relevant registers setting; Figure 2.3.27 and Figure 2.3.28 show the control procedure.
Timer Z count source selection bit f(XIN) = 8 MHz 1/16
Timer Z 1/65536
Timer Z interrupt request bit 0 or 1 131.072 ms 0 : No interrupt request issued 1 : Interrupt request issued
Fig. 2.3.25 Timers connection and setting of division ratios
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-41
APPLICATION 3804 Group (Spec.H) 2.3 Timer
Port P4 direction register (address 000916)
b7 b0
P4D
0 P47/CNTR2: Input mode
Timer Z mode register (address 002A16)
b7 b0
TZM
10
0011 Timer Z operating mode: Pulse width measurement mode Write in latch and timer at the same time CNTR2 active edge switch: "H" level width measurement Timer Z count: Stop Clear to "0" when starting count
Timer Y, Z count source selection register (address 000F16)
b7 b0
TYZCSS
0011 Timer Z count source: f(XIN)/16
Timer Z high-order (address 002916)
b7 b0
TZH
FF16 Set initial value "FFFF16" before starting pulse width measurement. (When not setting the initial value, count is started from the timer value before measurement start.)
Timer Z low-order (address 002816)
b7 b0
TZL
FF16
Interrupt source selection register (address 003916)
b7 b0
INTSEL
1
1 INT0/timer Z interrupt source: Timer Z interrupt INT4/CNTR2 interrupt source: CNTR2 interrupt
Interrupt request register 1 (address 003C16)
b7 b0
IREQ1
0 Timer Z interrupt request (Set to "1" automatically when Timer Z underflows)
Interrupt control register 1 (address 003E16)
b7 b0
ICON1
1 Timer Z interrupt: Enabled
Interrupt request register 2 (address 003D16)
b7 b0
IREQ2
0 CNTR2 interrupt request (Set to "1" automatically when "H" level input came to the end)
Interrupt control register 2 (address 003F16)
b7 b0
ICON2
1 CNTR2 interrupt: Enabled
Fig. 2.3.26 Relevant registers setting
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-42
APPLICATION 3804 Group (Spec.H) 2.3 Timer
RESET q x: This bit is not used here. Set it to "0" or "1" arbitrarily. Initialization SEI 0XXXXXXX2 (address 000916) P4D X10X00112 (address 002A16) TZM 0011XXXX2 TYZCSS (address 000F16) FF16 (address 002816) TZL FF16 (address 002916) TZH XXX1XXX12 INTSEL (address 003916) IREQ1 (address 003C16), bit0 0 ICON1 (address 003E16), bit0 1 IREQ2 (address 003D16), bit5 0 ICON2 (address 003F16), bit5 1 TZM CLI
.... .... .....
*All interrupts disabled *Set P47/CNTR2 pin to input mode *Timer Z: Pulse width measurement mode (Measure "H" level of pulses input from CNTR2 pin.) *Set timer Z initial value
*Timer Z interrupt enabled *CNTR2 interrupt enabled *Timer Z count start *Interrupts enabled
(address 002A16), bit6
0
Timer Z interrupt process routine
CLT (Note 1) CLD (Note 2) Push registers to stack
Note 1: When using Index X mode flag (T) Note 2: When using Decimal mode flag (D) *Push registers used in interrupt process routine
Error processing
Pop registers
*Pop registers pushed to stack
RTI
Note: Timer Z interrupt also occurs owing to factors other than measurement level. (CNTR2 input ="L" in this application) Process it by software as error processing is performed for measurement level as necessary. (CNTR2 input level can be checked by reading the contents of sharing port P47 register.)
Fig. 2.3.27 Control procedure (1)
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-43
APPLICATION 3804 Group (Spec.H) 2.3 Timer
CNTR2 interrupt process routine (Note 1) Notes 2: When using Index X mode flag (T) 3: When using Decimal mode flag (D) *Pushing registers used in interrupt process routine
CLT (Note 2) CLD (Note 3) Push registers to stack
(A) Measurement result (high-order 8 bits) (A) Measurement result (low-order 8 bits)
TZH (A) TZL (A)
*Count value read and storing it to RAM
Pop registers
*Popping registers pushed to stack
RTI Note 1: The first value becomes invalid depending on start timing of Timer Z count shown by the following figure. Process it by software as necessary.
[ Example 1] * Start Timer Z count when CNTR2 input level is "L". (CNTR2 input level can be checked by reading the contents of sharing port P47 register.) FFFF16
T1 T2 000016 T1 value: Valid CNTR2 Count start of Timer Z T2 value: Valid
CNTR2 interrupt
CNTR2 interrupt
[ Example 2] * Start Timer Z count when CNTR2 input level is "H". Invalidate the first CNTR2 interrupt after start of Timer Z count. FFFF16
T1 T2
000016 CNTR2
T1 value: Invalid
T2 value: Valid
Count start of CNTR2 interrupt Timer z
CNTR2 interrupt
Fig. 2.3.28 Control procedure (2)
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-44
APPLICATION 3804 Group (Spec.H) 2.3 Timer
2.3.4 Notes on timer Notes on 8-bit timer (timer 1, 2, X, Y) q If a value n (between 0 and 255) is written to a timer latch, the frequency division ratio is 1/(n+1). q When switching the count source by the timer 12, X and Y count source selection bits, the value of timer count is altered in unconsiderable amount owing to generating of thin pulses in the count input signals. Therefore, select the timer count source before set the value to the prescaler and the timer. q Set the double-function port of the CNTR0/CNTR1 pin and port P54/P55 to output in the pulse output mode. q Set the double-function port of CNTR0/CNTR1 pin and port P54/P55 to input in the event counter mode and the pulse width measurement mode. Notes on 16-bit timer (timer Z) (1) Pulse output mode q Set the double-function port of the CNTR2 pin and port P47 to output. (2) Pulse period measurement mode q Set the double-function port of the CNTR2 pin and port P47 to input. q A read-out of timer value is impossible in this mode. The timer can be written to only during timer stop (no measurement of pulse period). q Since the timer latch in this mode is specialized for the read-out of measured values, do not perform any write operation during measurement. q "FFFF16" is set to the timer when the timer underflows or when the valid edge of measurement start/completion is detected. Consequently, the timer value at start of pulse period measurement depends on the timer value just before measurement start. (3) Pulse width measurement mode q Set the double-function port of the CNTR2 pin and port P47 to input. q A read-out of timer value is impossible in this mode. The timer can be written to only during timer stop (no measurement of pulse period). q Since the timer latch in this mode is specialized for the read-out of measured values, do not perform any write operation during measurement. q "FFFF16" is set to the timer when the timer underflows or when the valid edge of measurement start/completion is detected. Consequently, the timer value at start of pulse width measurement depends on the timer value just before measurement start. (4) Programmable waveform generating mode q Set the double-function port of the CNTR2 pin and port P47 to output. (5) Programmable one-shot generating mode q Set the double-function port of CNTR2 pin and port P47 to output, and of INT1 pin and port P42 to input in this mode. q This mode cannot be used in low-speed mode. q If the value of the CNTR2 active edge switch bit is changed during one-shot generating enabled or generating one-shot pulse, then the output level from CNTR2 pin changes.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-45
APPLICATION 3804 Group (Spec.H) 2.3 Timer
(6) All modes qTimer Z write control Which write control can be selected by the timer Z write control bit (bit 3) of the timer Z mode register (address 002A16), writing data to both the latch and the timer at the same time or writing data only to the latch. When the operation "writing data only to the latch" is selected, the value is set to the timer latch by writing data to the address of timer Z and the timer is updated at next underflow. After reset release, the operation "writing data to both the latch and the timer at the same time" is selected, and the value is set to both the latch and the timer at the same time by writing data to the address of timer Z. In the case of writing data only to the latch, if writing data to the latch and an underflow are performed almost at the same time, the timer value may become undefined. qTimer Z read control A read-out of timer value is impossible in pulse period measurement mode and pulse width measurement mode. In the other modes, a read-out of timer value is possible regardless of count operating or stopped. However, a read-out of timer latch value is impossible. qSwitch of interrupt active edge of CNTR2 and INT1 Each interrupt active edge depends on setting of the CNTR2 active edge switch bit and the INT1 active edge selection bit. qSwitch of count source When switching the count source by the timer Z count source selection bits, the value of timer count is altered in inconsiderable amount owing to generating of thin pulses on the count input signals. Therefore, select the timer count source before setting the value to the prescaler and the timer.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-46
APPLICATION 3804 Group (Spec.H) 2.4 Serial interface
2.4 Serial interface
This paragraph explains the registers setting method and the notes relevant to Serial I/O. 2.4.1 Memory map
Address 001816 001916 001A16 001B16 001C16 001D16 001F16
Transmit/Receive buffer register 1 (TB1/RB1)
Serial I/O1 status register (SIO1STS) Serial I/O1 control register (SIO1CON) UART1 control register (UART1CON) Baud rate generator 1 (BRG1) Serial I/O2 control register (SIO2CON) Serial I/O2 register (SIO2)
002F16 003016 003116 003216 003316
Baud rate generator 3 (BRG3)
Transmit/Receive buffer register 3 (TB3/RB3)
Serial I/O3 status register (SIO3STS) Serial I/O3 control register (SIO3CON) UART3 control register (UART3CON)
003916 003C16 003D16 003E16 003F16
Interrupt source selection register (INTSEL)
Interrupt request register 1 (IREQ1) Interrupt request register 2 (IREQ2) Interrupt control register 1 (ICON1) Interrupt control register 2 (ICON2)
Fig. 2.4.1 Memory map of registers relevant to Serial I/O
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-47
APPLICATION 3804 Group (Spec.H) 2.4 Serial interface
2.4.2 Relevant registers
Transmit/Receive buffer register 1, Transmit/Receive buffer register 3
b7 b6 b5 b4 b3 b2 b1 b0 Transmit/Receive buffer register 1 (TB1/RB1: address 001816) Transmit/Receive buffer register 3 (TB3/RB3: address 003016)
b
0 1 2 3 4 5 6 7
Functions
The transmission data is written to or the receive data is read out from this buffer register. * At write: A data is written to the transmit buffer register. * At read: The contents of the receive buffer register are read out.
At reset R W
Undefined Undefined Undefined Undefined Undefined Undefined Undefined Undefined Note: The contents of transmit buffer register cannot be read out. The data cannot be written to the receive buffer register.
Fig. 2.4.2 Structure of Transmit/Receive buffer register 1 and Transmit/Receive buffer register 3
Serial I/O1 status register, Serial I/O3 status register
b7 b6 b5 b4 b3 b2 b1 b0 Serial I/O1 status register (SIO1STS: address 001916) Serial I/O3 status register (SIO3STS: address 003116)
b
Name
Functions
0: Buffer full 1: Buffer empty 0: Buffer empty 1: Buffer full 0: Transmit shift in progress 1: Transmit shift completed
0 Transmit buffer empty flag (TBE) 1 Receive buffer full flag (RBF) 2 Transmit shift register shift completion flag (TSC)
At reset R W 0
0 0

3 Overrun error flag 0: No error (OE) 1: Overrun error 4 Parity error flag 0: No error (PE) 1: Parity error 5 Framing error flag 0: No error (FE) 1: Framing error 6 Summing error flag 0: (OE) U (PE) U (FE) = 0 (SE) 1: (OE) U (PE) U (FE) = 1 7 Nothing is arranged for this bit. This bit is a write disabled bit. When this bit is read out, the contents are "1".
0 0 0 0 1
Fig. 2.4.3 Structure of Serial I/O1 status register and Serial I/O3 status register
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-48
APPLICATION 3804 Group (Spec.H) 2.4 Serial interface
Serial I/O1 control register
b7 b6 b5 b4 b3 b2 b1 b0 Serial I/O1 control register (SIO1CON: address 001A16)
b
Name
Functions
At reset R W
0 0
0 BRG count source 0: f(XIN) selection bit (CSS) 1: f(XIN)/4 When clock synchronous 1 Serial I/O1 synchronous clock serial I/O is selected, selection bit (SCS) 0: BRG output divided by 4 1: External clock input When UART is selected, 0: BRG output divided by 16 1: External clock input divided by16 2 SRDY1 output enable bit (SRDY) 3 Transmit interrupt source selection bit (TIC) 4 Transmit enable bit (TE) 5 Receive enable bit (RE) 6 Serial I/O1 mode selection bit (SIOM) 7 Serial I/O1 enable bit (SIOE) 0: I/O port (P47) 1: SRDY1 output pin 0: Transmit buffer empty 1: Transmit shift operation completion 0: Transmit disabled 1: Transmit enabled 0: Receive disabled 1: Receive enabled 0: UART 1: Clock synchronous serial I/O 0: Serial I/O1 disabled (P44 to P47: normal I/O pins) 1: Serial I/O1 enabled (P44 to P47: Serial I/O pins)
0 0
0 0 0
0
Fig. 2.4.4 Structure of Serial I/O1 control register
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-49
APPLICATION 3804 Group (Spec.H) 2.4 Serial interface
Serial I/O3 control register
b7 b6 b5 b4 b3 b2 b1 b0 Serial I/O3 control register (SIO3CON: address 003216)
b
Name
Functions
At reset R W
0 0
0 BRG count source 0: f(XIN) selection bit (CSS) 1: f(XIN)/4 When clock synchronous 1 Serial I/O3 synchronous clock serial I/O is selected, selection bit (SCS) 0: BRG output divided by 4 1: External clock input When UART is selected, 0: BRG output divided by 16 1: External clock input divided by16 2 SRDY3 output enable bit (SRDY) 3 Transmit interrupt source selection bit (TIC) 4 Transmit enable bit (TE) 5 Receive enable bit (RE) 6 Serial I/O3 mode selection bit (SIOM) 7 Serial I/O3 enable bit (SIOE) 0: I/O port (P37) 1: SRDY3 output pin 0: Transmit buffer empty 1: Transmit shift operation completion 0: Transmit disabled 1: Transmit enabled 0: Receive disabled 1: Receive enabled 0: UART 1: Clock synchronous serial I/O 0: Serial I/O3 disabled (P34 to P37: normal I/O pins) 1: Serial I/O3 enabled (P34 to P37: Serial I/O pins)
0 0
0 0 0
0
Fig. 2.4.5 Structure of Serial I/O3 control register
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-50
APPLICATION 3804 Group (Spec.H) 2.4 Serial interface
UART1 control register
b7 b6 b5 b4 b3 b2 b1 b0 UART1 control register (UART1CON: address 001B16)
b
Name
Functions
At reset R W
0 0 0 0 0
0 Character length 0: 8 bits selection bit (CHAS) 1: 7 bits 1 Parity enable bit (PARE) 2 Parity selection bit (PARS) 0: Parity checking disabled 1: Parity checking enabled 0: Even parity 1: Odd parity
3 Stop bit length 0: 1 stop bit selection bit (STPS) 1: 2 stop bits 4 P45/TxD1 P-channel 0: CMOS output output disable bit (in output mode) (POFF) 1: N-channel open-drain output (in output mode) 5 Nothing is arranged for these bits. These are 6 write disabled bits. When these bits are read out, the contents are "1". 7
1 1 1

Fig. 2.4.6 Structure of UART1 control register
UART3 control register
b7 b6 b5 b4 b3 b2 b1 b0 UART3 control register (UART3CON: address 003316)
b
Name
Functions
At reset R W
0 0 0 0 0
0 Character length 0: 8 bits selection bit (CHAS) 1: 7 bits 1 Parity enable bit (PARE) 2 Parity selection bit (PARS) 0: Parity checking disabled 1: Parity checking enabled 0: Even parity 1: Odd parity
3 Stop bit length 0: 1 stop bit selection bit (STPS) 1: 2 stop bits 4 P35/TxD3 P-channel 0: CMOS output output disable bit (in output mode) (POFF) 1: N-channel open-drain output (in output mode) 5 Nothing is arranged for these bits. These are 6 write disabled bits. When these bits are read out, the contents are "1". 7
1 1 1

Fig. 2.4.7 Structure of UART3 control register
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-51
APPLICATION 3804 Group (Spec.H) 2.4 Serial interface
Baud rate generator i (i = 1, 3)
b7 b6 b5 b4 b3 b2 b1 b0 Baud rate generator i (BRGi (i=1, 3): address 001C16, 002F16)
b
Functions
At reset R W
0 Set a count value of baud rate generator. Undefined 1 Undefined 2 Undefined 3 Undefined 4 Undefined 5 Undefined 6 Undefined 7 Undefined Note: Write to this register while transmit/receive operation is stopped.
Fig. 2.4.8 Structure of Baud rate generator 1 and Baud rate generator 3
Serial I/O2 control register
b7 b6 b5 b4 b3 b2 b1 b0 Serial I/O2 control register (SIO2CON: address 001D16)
b
Name
b2b1b0
Functions
0 0 0: f(XIN)/8 0 0 1: f(XIN)/16 0 1 0: f(XIN)/32 0 1 1: f(XIN)/64 1 1 0: f(XIN)/128 1 1 1: f(XIN)/256 0: I/O port (P51, P52) 1: SOUT2, SCLK2 signal output 0: I/O port (P53) 1: SRDY2 signal output 0: LSB first 1: MSB first 0: External clock 1: Internal clock 0: CMOS output (in output mode) 1: N-channel open-drain output (in output mode)
At reset R W
0 0 0 0 0 0 0
0 Internal synchronous clock 1 selection bits 2 3 Serial I/O2 port selection bit 4 SRDY2 output enable bit 5 Transfer direction selection bit 6 Serial I/O2 synchronous clock selection bit 7 P51/SOUT2 P-channel output disable bit
0
Fig. 2.4.9 Structure of Serial I/O2 control register
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-52
APPLICATION 3804 Group (Spec.H) 2.4 Serial interface
Serial I/O2 register
b7 b6 b5 b4 b3 b2 b1 b0 Serial I/O2 register (SIO2: address 001F16)
b
0 1 2 3 4 5 6 7
Name
Functions
At reset R W
Undefined Undefined Undefined Undefined Undefined Undefined Undefined Undefined
This register becomes shift register. At transmit: Set transmit data to this register. At receive: Received data is stored to this register.
Fig. 2.4.10 Structure of Serial I/O2 register
Interrupt source selection register
b7 b6 b5 b4 b3 b2 b1 b0 Interrupt source selection register (INTSEL: address 003916)
b
Name
Functions
0: INT0 interrupt 1: Timer Z interrupt 0: Serial I/O2 interrupt 1: Timer Z interrupt 0: Serial I/O1 transmit interrupt 1: SCL, SDA interrupt 0: CNTR0 interrupt 1: SCL, SDA interrupt 0: INT4 interrupt 1: CNTR2 interrupt 0: INT2 interrupt 1: I2C interrupt 0: CNTR1 interrupt 1: Serial I/O3 receive interrupt 0: A/D converter interrupt 1: Serial I/O3 transmit interrupt
At reset R W
0
0 INT0/Timer Z interrupt source selection bit (*1) 1 Serial I/O2/Timer Z interrupt source selection bit (*1) 2 Serial I/O1 transmit/ SCL, SDA interrupt source selection bit (*2) 3 CNTR0/SCL, SDA interrupt source selection bit (*2) 4 INT4/CNTR2 interrupt source selection bit 5 INT2/I2C interrupt source selection bit 6 CNTR1/Serial I/O3 receive interrupt source selection bit 7 AD converter/Serial I/O3 transmit interrupt source selection bit
0
0
0
0
0 0
0
*1: Do not write 1 to these bits simultaneously. *2: Do not write 1 to these bits simultaneously.
Fig. 2.4.11 Structure of Interrupt source selection register
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-53
APPLICATION 3804 Group (Spec.H) 2.4 Serial interface
Interrupt request register 1
b7 b6 b5 b4 b3 b2 b1 b0 Interrupt request register 1 (IREQ1 : address 003C16)
b
Name
Functions
At reset R W
0 0 0 0
0 INT0/Timer Z 0 : No interrupt request issued interrupt request bit 1 : Interrupt request issued 1 INT1 interrupt request bit
0 : No interrupt request issued
1 : Interrupt request issued
2 Serial I/O1 receive 0 : No interrupt request issued interrupt request bit 1 : Interrupt request issued
0 : No interrupt request issued 3 Serial I/O1 transmit/SCL, SDA 1 : Interrupt request issued interrupt request bit
4 Timer X interrupt request bit 5 Timer Y interrupt request bit 6 Timer 1 interrupt request bit
0 : No interrupt request issued
0 0 0 0

1 : Interrupt request issued
0 : No interrupt request issued
1 : Interrupt request issued
0 : No interrupt request issued
1 : Interrupt request issued
7 Timer 2 interrupt 0 : No interrupt request issued request bit 1 : Interrupt request issued : 0 can be set by software, but 1 cannot be set.
Fig. 2.4.12 Structure of Interrupt request register 1
Interrupt request register 2
b7 b6 b5 b4 b3 b2 b1 b0 Interrupt request register 2 (IREQ2 : address 003D16)
b
Name
Functions
0 : No interrupt request issued 1 : Interrupt request issued 0 : No interrupt request issued 1 : Interrupt request issued 0 : No interrupt request issued 1 : Interrupt request issued 0 : No interrupt request issued 1 : Interrupt request issued 0 : No interrupt request issued 1 : Interrupt request issued 0 : No interrupt request issued 1 : Interrupt request issued 0 : No interrupt request issued 1 : Interrupt request issued
At reset R W
0 0
0 CNTR0/SCL, SDA interrupt request bit 1 CNTR1/Serial I/O3 receive interrupt request bit 2 Serial I/O2/Timer Z interrupt request bit 3 INT2/I2C interrupt request bit 4 INT3 interrupt request bit 5 INT4/CNTR2 interrupt request bit 6 AD converter/Serial I/O3 transmit interrupt request bit
0 0 0 0 0

7 Nothing is arranged for this bit. This is a write disabled bit. When this bit is read out, the contents are 0 . : 0 can be set by software, but 1 cannot be set.
0
Fig. 2.4.13 Structure of Interrupt request register 2
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-54
APPLICATION 3804 Group (Spec.H) 2.4 Serial interface
Interrupt control register 1
b7 b6 b5 b4 b3 b2 b1 b0 Interrupt control register 1 (ICON1 : address 003E16)
b
Name
Functions
0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled
At reset R W
0 0 0 0
0 INT0/Timer Z interrupt enable bit 1 INT1 interrupt enable bit 2 Serial I/O1 receive interrupt enable bit 3 Serial I/O1 transmit/SCL, SDA interrupt enable bit 4 Timer X interrupt enable bit 5 Timer Y interrupt enable bit 6 Timer 1 interrupt enable bit 7 Timer 2 interrupt enable bit
0 0 0 0
Fig. 2.4.14 Structure of Interrupt control register 1
Interrupt control register 2
b7 b6 b5 b4 b3 b2 b1 b0
0
Interrupt control register 2 (ICON2 : address 003F16)
b
Name
Functions
0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled
At reset R W
0 0
0 CNTR0/SCL, SDA interrupt enable bit 1 CNTR1/ Serial I/O3 receive interrupt enable bit 2 Serial I/O2/ Timer Z interrupt enable bit 3 INT2/I2C interrupt enable bit 4 INT3 interrupt enable bit 5 INT4/CNTR2 interrupt enable bit 6 AD converter/Serial I/O3 transmit interrupt enable bit 7 Fix this bit to "0".
0 0 0 0 0
0
Fig. 2.4.15 Structure of Interrupt control register 2
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-55
APPLICATION 3804 Group (Spec.H) 2.4 Serial interface
2.4.3 Serial I/O connection examples (1) Control of peripheral IC equipped with CS pin Figure 2.4.16 shows connection examples of a peripheral IC equipped with the CS pin. There are connection examples using a clock synchronous serial I/O mode.
(1) Only transmission (Using the RXDi pin as an I/O port) Port SCLKi TXDi CS CLK DATA
(2) Transmission and reception
Port SCLKi TXDi RXDi 3804 group (Spec. H)
CS CLK IN OUT Peripheral IC 2 (E PROM etc.)
3804 group Peripheral IC (Spec. H) (OSD controller etc.) (3) Transmission and reception (When connecting RXDi with TXDi) (When connecting IN with OUT in peripheral IC) Port SCLKi TXDi RXDi CS CLK IN
(4) Connection of plural IC Port SCLKi TXDi RXDi Port 3804 group (Spec. H) CS CLK IN OUT Peripheral IC 1
OUT 3804 group 1 Peripheral IC 2 2 (Spec. H) (E PROM etc.)
CS CLK IN OUT Peripheral IC 2
1:
Select an N-channel open-drain output for TXDi pin output control. 2: Use the OUT pin of peripheral IC which is an N-channel opendrain output and becomes high impedance during receiving data.
Notes 1: "Port" means an output port controlled by software. 2: Use SOUT2 and SIN2 instead of TxDi and RxDi for the serial I/O2. (i = 1, 3)
Fig. 2.4.16 Serial I/O connection examples (1)
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-56
APPLICATION 3804 Group (Spec.H) 2.4 Serial interface
(2) Connection with microcomputer Figure 2.4.17 shows connection examples with another microcomputer.
(1) Selecting internal clock SCLKi TXDi RXDi 3804 group (Spec. H) CLK IN OUT Microcomputer
(2) Selecting external clock SCLKi TXDi RXDi 3804 group (Spec. H) CLK IN OUT Microcomputer
(3) Using SRDYi signal output function (Selecting an external clock)
SRDYi
(4) In UART
RDY CLK IN OUT Microcomputer
TXDi RXDi 3804 group (Spec. H)
RXD TXD Microcomputer
SCLKi TXDi RXDi 3804 group (Spec. H)
UART cannot be used for serial I/O2. Note: Use SOUT2 and SIN2 instead of TxDi and RxDi for the serial I/O2. (i = 1, 3)
Fig. 2.4.17 Serial I/O connection examples (2)
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-57
APPLICATION 3804 Group (Spec.H) 2.4 Serial interface
2.4.4 Setting of serial I/O transfer data format A clock synchronous or clock asynchronous (UART) can be selected as a data format of serial I/O1 and serial I/O3. Serial I/O2 operates in a clock synchronous. Figure 2.4.18 shows the serial I/O transfer data format.
1ST-8DATA-1SP
ST LSB MSB SP
1ST-7DATA-1SP
ST LSB MSB SP
1ST-8DATA-1PAR-1SP
ST LSB MSB PAR SP
1ST-7DATA-1PAR-1SP
ST LSB MSB PAR SP
UART
1ST-8DATA-2SP
ST LSB MSB 2SP
1ST-7DATA-2SP
ST LSB MSB 2SP
Serial I/O1 Serial I/O3
1ST-8DATA-1PAR-2SP
ST LSB MSB PAR 2SP
1ST-7DATA-1PAR-2SP
ST LSB MSB PAR 2SP
Clock synchronous Serial I/O
LSB first
Serial I/O2
Clock synchronous Serial I/O
LSB first MSB first
ST : Start bit SP : Stop bit PAR : Parity bit
Fig. 2.4.18 Serial I/O transfer data format
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-58
APPLICATION 3804 Group (Spec.H) 2.4 Serial interface
2.4.5 Serial I/O1, serial I/O3 operation: stop and initialize Serial I/O1 and serial I/O3 perform the same operation. In the following explanations when names of serial I/O1 and serial I/O3 are different, serial I/O1s' are showed first and then serial I/O3s' in the marked ( ). (1) Clock synchronous serial I/O mode sStop/initialize transmit operation when only transmitting When using an internal clock, set the transmit enable bit and serial I/O1 enable bit (serial I/O3 enable bit) to "0". When using an external clock, set the transmit enable bit to "0". By setting the transmit enable bit to "0", the transmit operations listed below will be stopped or initialized. However, when using an internal clock, the clock is output in 8 pulses, even if the transmit enable bit is set to "0" during transmit operations. *Stop supply of shift clock to transmit shift register *Initialize clock control circuit for transmit *Transmit buffer empty flag = "0" *Transmit shift register shift complete flag = "0" *P45/TxD1 pin: input/output port P45 (P35/TxD3 pin: input/output port P35) By setting the serial I/O1 enable bit (serial I/O3 enable bit) to "0", pins P44/RxD1, P45/TxD1, P46/ SCLK1, and P47/SRDY1 (P34/RxD3, P35/TxD3, P36/SCLK3, P37/SRDY3 pins) all become I/O ports. As a result, the internal clock cannot be output externally. sStop/initialize receive operation when only receiving When using an internal clock, set the receive enable bit and serial I/O1 enable bit (serial I/O3 enable bit) to "0". When using an external clock, set the receive enable bit or serial I/O1 enable bit (serial I/O3 enable bit) to "0". By setting the receive enable bit to "0", the receive operations listed below will be stopped or initialized. However, when using an internal clock, the clock is output in 8 pulses, even if the receive enable bit is set to "0" during receive operations. *Stop supply of shift clock to receive shift register *Initialize clock control circuit for receive *Error flags (over-run, parity, framing, and summing error flags) = "0" *Receive buffer full flag = "0" *P44/RxD1 pin: input/output port P44 (P34/RxD3 pin: input/output port P34) By setting the serial I/O1 enable bit (serial I/O3 enable bit) to "0", the receive operations listed below will be stopped or initialized. As a result, the internal clock cannot be output externally. *Stop supply of shift clock to receive shift register *Initialize clock control circuit for receive *Error flags (over-run, parity, framing, and summing error flags) = "0" *Receive buffer full flag = "0" *P44/RxD1, P45/TxD1, P46/SCLK1, P47/SRDY1 pins: I/O ports P44, P45, P46, P47 (P34/RxD3, P35/TxD3, P36/SCLK3, P37/SRDY3 pins: I/O ports P34, P35, P36, P37) sStop/initialize receive/transmit operation when both receiving and transmitting Set the transmit enable bit and receive enable bit to "0" simultaneously. When using an internal clock, also set the serial I/O1 enable bit (serial I/O3 enable bit) to "0". (2) UART Mode sStop/initialize transmit operation Set the transmit enable bit to "0". sStop/initialize receive operation Set the receive enable bit to "0".
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-59
APPLICATION 3804 Group (Spec.H) 2.4 Serial interface
2.4.6 Serial I/O pin function and selection method (1) Serial I/O1, serial I/O3 Table 2.4.1 shows the pin function in the clock synchronous serial I/O mode, Table 2.4.2 shows the pin function in the UART mode. Table 2.4.1 Pin function in clock synchronous serial I/O mode
Serial I/O1 control register (address 001A16) Serial I/O3 control register (address 003216) Pin name (Serial I/O1) Pin name (Serial I/O3) Function
(No te 1)
b7
b6
b5 RE 1 0 1
b4 TE 1 1 0 1 1 1
b3 T IC
b2 SRDY 1 0
b1 SCS 1 0
SIOE SIOM RxD1, RxD3 P44/RxD1 P34/RxD3 P44, P34 TxD1, TxD3 P45, P35 SCLK1 (External clock input) P46/SCLK1
(Note 2)
Corresponding direction CSS register b0 0/1 0/1 0/1
1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1
P45/TxD1
P35/TxD3
P36/SCLK3
SCLK1 (Internal clock output) SRDY1, SRDY3
P47/SRDY1 /CNTR2
P37/SRDY3
P47, P37
Note 1: When SIOE is set to "0", all pins become I/O ports regardless of set value of b6-b0. Note 2: In the pulse output mode, the programmable waveform generating mode, or the programmable one-shot generating mode of the timer Z, this pin functions as the timer Z function output pin regardless of b7-b0 setting. : This is not used for the pin's function setting.
Table 2.4.2 Pin function in UART mode
Serial I/O1 control register (address 001A16) Pin name (Serial I/O1) Pin name (Serial I/O3) RxD P44/RxD1 P34/RxD3 P44 TxD P45/TxD1 P35/TxD3 P45 SCLK1 (External clock input) P46/SCLK1
(Note 2)
Function
(No te 1)
b7
b6 SIOM 0 0 0 0 0 0 0
b5 RE 1 0
b4 TE 1 0
b3 TIC
b2 SRDY
b1 SCS 1 0
SIOE 1 1 1 1 1 1 1
Corresponding direction CSS register b0 0/1 0/1 0/1 0/1
P36/SCLK3
P46 P47
P47/SRDY1 /CNTR2
P37/SRDY3
Note 1: When SIOE is set to "0", all pins become I/O ports regardless of set value of b6-b0. Note 2: In the pulse output mode, the programmable waveform generating mode, or the programmable one-shot generating mode of the timer Z, this pin functions as the timer Z function output pin regardless of b7-b0 setting. : This is not used for the pin's function setting.
(2) Serial I/O2 Table 2.4.3 shows the pin function in the clock synchronous serial I/O mode. Table 2.4.3 Pin function in clock synchronous serial I/O mode
Serial I/O2 control register (address 001D16) Pin name SIN2 P50 SOUT2 P51 SCLK2 (External clock input) P52/SCLK2 SCLK2 (Internal clock output) P52 P53/SRDY2 SRDY2 P53
(Note 2) C orrespo nding d irection register
Function
(Note 1)
b7
b6 0 1
b5
b4 1 0
b3 1 1 1 0 1 1 0
b2
b1
b0
P50/SIN2
0 0/1 0/1 0/1 0/1
CMOS output N-channel open-drain output
0 1
(No te 3)
P51/SOUT2

Notes 1: Although this pin functions as SIN2 when b3 is set to "0", set "1" to b3. Notes 2: Although this pin functions as SCLK2 when b3 and the corresponding direction register are set to "0", set "1" to b3. Notes 3: When the corresponding direction register bit is "1", the b7 setting is valid. : This is not used for the pin's function setting.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-60
APPLICATION 3804 Group (Spec.H) 2.4 Serial interface
2.4.7 Serial I/O application examples (1) Communication using clock synchronous serial I/O (transmit/receive) Outline : 2-byte data is transmitted and received, using the clock synchronous serial I/O. The SRDY1 signal is used for communication control. Figure 2.4.19 shows a connection diagram, and Figure 2.4.20 shows a timing chart. Figure 2.4.21 shows a registers setting relevant to the transmitting side, and Figure 2.4.22 shows registers setting relevant to the receiving side.
Transmitting side
Receiving side
P42/INT1
SRDY1
SCLK1 TXD1 3804 group (Spec. H)
SCLK1 RXD1 3804 group (Spec. H)
Note: Use SOUT2 and SIN2 instead of TxDi and RxDi for the serial I/O2. (i = 1, 3)
Fig. 2.4.19 Connection diagram Specifications : * * * * Serial I/O is used (clock synchronous serial I/O is selected.) Synchronous clock frequency : 125 kHz (f(XIN) = 4 MHz is divided by 32) SRDY1 (receivable signal) is used. The receiving side outputs SRDY1 signal at intervals of 2 ms (generated by timer), and 2-byte data is transferred from the transmitting side to the receiving side.
SRDY1 SCLK1
.... ....
TXD
D0 D1 D2 D3 D4 D5 D6 D7
D0 D1 D2 D3 D4 D5 D6 D7
D0 D1
....
2 ms
Fig. 2.4.20 Timing chart (using clock synchronous serial I/O)
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-61
APPLICATION 3804 Group (Spec.H) 2.4 Serial interface
Transmitting side
Port P4 direction register (Address : 000916)
b7 b0
P4D
0
Port P42/INT1: Input mode
Serial I/O1 status register (Address : 001916)
b7 b0
SIO1STS
Transmit buffer empty flag * Confirm that the data has been transferred from Transmit buffer register to Transmit shift register. * When this flag is "1", it is possible to write the next transmission data in to Transmit buffer register. Transmit shift register shift completion flag Confirm completion of transmitting 1-byte data with this flag. "1" : Transmit shift completed
Serial I/O1 control register (Address : 001A16)
b7 b0
SIO1CON
1101
00
BRG count source : f(XIN) Serial I/O1 synchronous clock : BRG/4 Transmit enabled Receive disabled Clock synchronous serial I/O Serial I/O1 enabled
Baud rate generator 1 (Address : 001C16)
b7 b0
BRG1
8-1
Set "division ratio - 1"
Interrupt edge selection register (Address : 003A16)
b7 b0
INTEDGE
0
INT1 falling edge active
Fig. 2.4.21 Registers setting relevant to transmitting side
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-62
APPLICATION 3804 Group (Spec.H) 2.4 Serial interface
Receiving side
Serial I/O1 status register (Address : 001916)
b7 b0
SIO1STS
Receive buffer full flag Confirm completion of receiving 1-byte data with this flag. "1" : at completing reception "0" : at reading out contents of Receive buffer register Overrun error flag "1" : When data is ready in Receive shift register while Receive buffer register contains the data. Parity error flag "1" : When a parity error occurs in enabled parity. Framing error flag "1" : When stop bits cannot be detected at the specified timing Summing error flag "1" : when any one of the following errors occurs. * Overrun error * Parity error * Framing error
Serial I/O1 control register (Address : 001A16)
b7 b0
SIO1CON
1111
11
Serial I/O1 synchronous clock : External clock
SRDY1 output enabled
Transmit enabled Set this bit to "1", using SRDY1 output. Receive enabled Clock synchronous serial I/O Serial I/O1 enabled
Fig. 2.4.22 Registers setting relevant to receiving side
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-63
APPLICATION 3804 Group (Spec.H) 2.4 Serial interface
Figure 2.4.23 shows a control procedure of the transmitting side, and Figure 2.4.24 shows a control procedure of the receiving side.
RESET
q x: This bit is not used here. Set it to "0" or "1" arbitrarily.
Initialization SIO1CON (Address : 001A16) 1101xx002 (Address : 001C16) 8-1 BRG1 0 INTEDGE (Address : 003A16), bit1
... ..
IREQ1 (Address: 003C16), bit1? 1 IREQ1 (Address : 003C16), bit1 0
0
* Detection of INT1 falling edge
TB1/RB1 (Address : 001816)
The first byte of a transmission data
* Transmission data write Transmit buffer empty flag is set to "0" by this writing.
SIO1STS (Address : 001916), bit0? 1 TB1/RB1 (Address : 001816)
0
* Judgment of transferring from Transmit buffer register to Transmit shift register (Transmit buffer empty flag) * Transmission data write Transmit buffer empty flag is set to "0" by this writing.
The second byte of a transmission data
SIO1STS (Address : 001916), bit0? 1
0
* Judgment of transferring from Transmit buffer register to Transmit shift register (Transmit buffer empty flag)
SIO1STS (Address : 001916), bit2? 1
0
* Judgment of shift completion of Transmit shift register (Transmit shift register shift completion flag)
Fig. 2.4.23 Control procedure of transmitting side
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-64
APPLICATION 3804 Group (Spec.H) 2.4 Serial interface
RESET
q x: This bit is not used here. Set it to "0" or "1" arbitrarily.
Initialization SIO1CON (Address : 001A16)
... ..
1111x11x2
N Pass 2 ms? Y TB1/RB1 (Address : 001816) Dummy data * SRDY1 output SRDY1 signal is outpu t by writing data to the TB1/RB1. Using the SRDY1, set Transmit enable bit (bit 4) of the SIO1CON to "1". * Judgment of completion of receiving (Receive buffer full flag) * An interval of 2 ms generated by Timer.
0 SIO1STS (Address : 001916), bit1? 1 Read out reception data from TB1/RB1 (Address : 001816) * Reception of the first byte data. Receive buffer full flag is set to "0" by reading data.
0 SIO1STS (Address : 001916), bit1? 1 Read out reception data from TB1/RB1 (Address : 001816) * Reception of the second byte data. Receive buffer full flag is set to "0" by reading data. * Judegment of completion of receiving (Receive buffer full flag)
Fig. 2.4.24 Control procedure of receiving side
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-65
APPLICATION 3804 Group (Spec.H) 2.4 Serial interface
(2) Output of serial data (control of peripheral IC) Outline : 4-byte data is transmitted and received, using the clock synchronous serial I/O. The CS signal is output to a peripheral IC through port P63. Figure 2.4.25 shows connection diagrams of example for using serial I/O1 and example for using serial I/O2 with the same specification, and Figure 2.4.26 shows a timing chart.
P63 SCLK1 TXD1
CS CLK DATA
CS CLK DATA
P63 SCLK2 SOUT2
CS CLK DATA
CS CLK DATA
3804 group (Spec. H)
Peripheral IC
3804 group (Spec. H)
Peripheral IC
(1) Example for using Serial I/O1
(2) Example for using Serial I/O2
Fig. 2.4.25 Connection diagrams Specifications : * Serial I/O is used (clock synchronous serial I/O is selected.) * Synchronous clock frequency : 125 kHz (f(XIN) = 4 MHz is divided by 32) * Transfer direction : LSB first * The Serial I/O interrupt is not used. * Port P63 is connected to the CS pin ("L" active) of the peripheral IC for transmission control; the output level of port P63 is controlled by software.
CS
CLK
DATA
DO0
DO1
DO2
DO3
Note: When using serial I/O2, the SOUT2 pin becomes the high-impedance state after transfer is completed.
Fig. 2.4.26 Timing chart (serial I/O1)
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-66
APPLICATION 3804 Group (Spec.H) 2.4 Serial interface
Figure 2.4.27 shows registers setting relevant to serial I/O1, and Figure 2.4.28 shows a setting of serial I/O1 transmission data.
Serial I/O1 control register (Address : 001A16)
b7 b0
SIO1CON
11011000
BRG count source : f(XIN) Serial I/O1 synchronous clock : BRG/4 SRDY1 output disabled Transmit interrupt source : Transmit shift operating completion Transmit enabled Receive disabled Clock synchronous serial I/O Serial I/O1 enabled
UART1 control register (Address : 001B16)
b7 b0
UART1CON
0
P45/TXD1 pin : CMOS output
Baud rate generator 1 (Address : 001C16)
b7 b0
BRG1
8 -1
b7 b0
Set "division ratio - 1"
Interrupt control register 1 (Address : 003E16) ICON1 0
Serial I/O1 transmit interrupt : Disabled
Interrupt request register 1 (Address : 003C16)
b7 b0
IREQ1
0
Serial I/O1 transmit interrupt request Confirm completion of transmitting 1-byte data by one unit. "1" : Transmit shift completion
Port P6 (Address : 000C16)
b7 b0
P6
1
Port P63: CS signal to peripheral ICs "L" active
Port P6 direction register (Address : 000D16)
b7 b0
P6D
1
Port P63: Output mode
Fig. 2.4.27 Registers setting relevant to serial I/O1
Transmit/Receive buffer register 1 (Address : 001816)
b7 b0
TB1/RB1
Set a transmission data. Confirm that transmission of the previous data is completed (bit 3 of the Interrupt request register 1 is "1") before writing data.
Fig. 2.4.28 Setting of serial I/O1 transmission data
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-67
APPLICATION 3804 Group (Spec.H) 2.4 Serial interface
When the registers are set as shown in Fig. 2.4.27, serial I/O1 can transmit 1-byte data by writing data to the transmit buffer register. Thus, after setting the CS signal to "L", write the transmission data to the transmit buffer register by each 1 byte, and return the CS signal to "H" when the target number of bytes has been transmitted. Figure 2.4.29 shows a control procedure of serial I/O1.
RESET
q X: This bi t is not used here. Set it to "0" or "1" arbitrarily. q
Initialization SIO1CON (Address : 001A16) 110110002 0 UART1CON(Address : 001B16), bit4 8-1 BRG1 (Address : 001C16) 0 ICON1 (Address : 003E16), bit3 1 P6 (Address : 000C16), bit3 P6D (Address : 000D16) XXXX1XXX2
.... ....
* Serial I/O1 setting
* Serial I/O1 transmit interrupt : Disabled * CS signal output port setting ("H" level output)
P6 (Address : 000C16), bit3
0
* CS signal output level to "L" setting
IREQ1 (Address : 003C16), bit3
0
* Serial I/O1 transmit interrupt request bit to "0" setting
TB1/RB1 (Address : 001816)
a transmission data
* Transmission data write (Start of transmit 1-byte data)
IREQ1 (Address : 003C16), bit3? 1
0
* Judgment of completion of transmitting 1-byte data
N
Complete to transmit data? Y
* Use any of RAM area as a counter for counting the number of transmitted bytes * Judgment of completion of transmitting the target number of bytes
P6 (Address : 000C16), bit3
1
* Returning CS signal output level to "H" when transmission of the target number of bytes is completed
Fig. 2.4.29 Control procedure of serial I/O1
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-68
APPLICATION 3804 Group (Spec.H) 2.4 Serial interface
Figure 2.4.30 shows registers setting relevant to serial I/O2, and Figure 2.4.31 shows a setting of serial I/O2 transmission data.
Serial I/O2 control register (Address : 001D16)
b7 b0
SIO2CON
1001010
Synchronous clock : f(XIN)/32 Serial I/O2 used SRDY2 output disabled LSB first Internal clock
Interrupt source selection register (Address : 003916)
b7 b0
INTSEL
0
Serial I/O2/timer Z interrupt source selection : Serial I/O2 interrupt
Interrupt control register 2 (Address : 003F16)
b7 b0
ICON2
0
Serial I/O2 interrupt : Interrupt disabled
Interrupt request register 2 (Address : 003D16)
b7 b0
IREQ2
0
Serial I/O2 interrupt request Confirm completion of transmitting 1-byte data by one unit. "1" : Transmit shift completion
Port P6 (Address : 000C16)
b7 b0
P6
1
Port P63: CS signal to peripheral ICs "L" active
Port P6 direction register (Address : 000D16)
b7 b0
P6D
1
Port P63: Output mode
Fig. 2.4.30 Registers setting relevant to serial I/O2
Serial I/O2 register (Address : 001F16)
b7 b0
SIO2
Set a transmission data. Confirm that transmission of the previous data is completed (bit 2 of the Interrupt request register 2 is "1") before writing data.
Fig. 2.4.31 Setting of serial I/O2 transmission data
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-69
APPLICATION 3804 Group (Spec.H) 2.4 Serial interface
When the registers are set as shown in Fig. 2.4.30, serial I/O2 can transmit 1-byte data by writing data to the serial I/O2 register. Thus, after setting the CS signal to "L", write the transmission data to the serial I/O2 register by each 1 byte, and return the CS signal to "H" when the target number of bytes has been transmitted. Figure 2.4.32 shows a control procedure of serial I/O2.
RESET
q X: This bi t is not used here. Set it to "0" or "1" arbitrarily. q
Initialization SIO2CON (Address : 001D16) 010010102 INTSEL (Address : 003916) XXXXXX0X2 ICON2 (Address : 003F16), bit2 0 P6 (Address : 000C16), bit3 1 P6D (Address : 000D16) XXXX1XXX2
.... ....
* Serial I/O2 control register setting * Serial I/O2 interrupt : Disabled * CS signal output port setting ("H" level output)
P6 (Address : 000C16), bit3
0
* CS signal output level to "L" setting
IREQ2 (Address : 003D16), bit2
0
* Serial I/O2 interrupt request bit to "0" setting
SIO2 (Address : 001F16)
a transmission data
* Transmission data write (Start of transmit 1-byte data)
IREQ2 (Address : 003D16), bit2? 1
0
* Judgment of completion of transmitting 1-byte data
N
Complete to transmit data? Y
* Use any of RAM area as a counter for counting the number of transmitted bytes. * Judgment of completion of transmitting the target number of bytes
P6 (Address : 000C16), bit3
1
* Returning CS signal output level to "H" when transmission of the target number of bytes is completed
Fig. 2.4.32 Control procedure of serial I/O2
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-70
APPLICATION 3804 Group (Spec.H) 2.4 Serial interface
(3) Cyclic transmission or reception of block data (data of specified number of bytes) between two microcomputers Outline : When the clock synchronous serial I/O is used for communication, synchronization of the clock and the data between the transmitting and receiving sides may be lost because of noise included in the synchronous clock. It is necessary to correct that constantly, using "heading adjustment". This "heading adjustment" is carried out by using the interval between blocks in this example. This example is described for serial I/O1, but this example also can apply serial I/O3. Figure 2.4.33 shows connection diagram.
SCLK1 RXD1 TXD1 Master unit
SCLK1 TXD1 RXD1 Slave unit
Note: Use SOUT2 and SIN2 instead of TxD1 and RxD1 for serial I/O2.
Fig. 2.4.33 Connection diagram
Specifications : * * * * * * * *
Serial I/O is used (clock synchronous serial I/O is selected). Synchronous clock frequency : 131 kHz (f(XIN) = 4.19 MHz is divided by 32) Byte cycle: 488 s Number of bytes for transmission or reception : 8 byte/block Block transfer cycle : 16 ms Block transfer term : 3.5 ms Interval between blocks : 12.5 ms Heading adjustment time : 8 ms
Limitations of the specifications : * Reading of the reception data and setting of the next transmission data must be completed within the time obtained from "byte cycle - time for transferring 1-byte data" (in this example, the time taken from generating of the serial I/O1 receive interrupt request to input of the next synchronous clock is 431 s). * "Heading adjustment time < interval between blocks" must be satisfied.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-71
APPLICATION 3804 Group (Spec.H) 2.4 Serial interface
The communication is performed according to the timing shown in Figure 2.4.34. In the slave unit, when a synchronous clock is not input within a certain time (heading adjustment time), the next clock input is processed as the beginning (heading) of a block. When a clock is input again after one block (8 byte) is received, the clock is ignored. Figure 2.4.35 shows relevant registers setting.
D0
D1
D2
D7
D0
Byte cycle Block transfer term Block transfer cycle Heading adjustment time Interval between blocks
Processing for heading adjustment
Fig. 2.4.34 Timing chart
Master unit
Serial I/O1 control register (Address : 001A16) b7 b0 SIO1CON 1 1 1 1 1 0 0 0 BRG count source : f(XIN) Synchronous clock : BRG/4 SRDY1 output disabled Transmit interrupt source : Transmit shift operating completion Transmit enabled Receive enabled Clock synchronous serial I/O Serial I/O1 enabled
Slave unit
Serial I/O1 control register (Address : 001A16) b7 b0 SIO1CON 1 1 1 1
01
Not be affected by external clock Synchronous clock : External clock SRDY1 output disabled Not use the serial I/O1 transmit interrupt Transmit enabled Receive enabled Clock synchronous serial I/O Serial I/O1 enabled
Both of units
UART1 control register (Address : 001B16) b7 b0 UART1CON
0
P45/TXD1 pin : CMOS output Baud rate generator 1 (Address : 001C16) b7 b0
BRG1
8-1
Set "division ratio - 1"
Fig. 2.4.35 Relevant registers setting
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-72
APPLICATION 3804 Group (Spec.H) 2.4 Serial interface
Control procedure : q Control in the master unit After setting the relevant registers shown in Figure 2.4.35, the master unit starts transmission or reception of 1-byte data by writing transmission data to the transmit buffer register. To perform the communication in the timing shown in Figure 2.4.34, take the timing into account and write transmission data. Additionally, read out the reception data when the serial I/O1 transmit interrupt request bit is set to "1," or before the next transmission data is written to the transmit buffer register. Figure 2.4.36 shows a control procedure of the master unit using timer interrupts.
Interrupt processing routine executed every 488s
CLT (Note 1) CLD (Note 2) Push register to stack
q
Note 1: When using the Index X mode flag (T). Note 2: When using the Decimal mode flag (D). Push the register used in the interrupt processing routine into the stack.
Within a block transfer period? Y Read a reception data
N
q
Generate a certain block interval by using a timer or other functions.
q
Count a block interval counter
Check the block interval counter and determine to start a block transfer.
Complete to transfer a block? N Write a transmission data
Y
Start a block transfer? Y Write the first transmission data (first byte) in a block
N
Pop registers
q
Pop registers which is pushed to stack.
RTI
Fig. 2.4.36 Control procedure of master unit
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-73
APPLICATION 3804 Group (Spec.H) 2.4 Serial interface
q Control in the slave unit After setting the relevant registers as shown in Figure 2.4.35, the slave unit becomes the state where a synchronous clock can be received at any time, and the serial I/O1 receive interrupt occurs each time an 8-bit synchronous clock is received. In the serial I/O1 receive interrupt processing routine, the data to be transmitted next is written to the transmit buffer register after the received data is read out. However, if no serial I/O1 receive interrupt occurs for a certain time (heading adjustment time or more), the following processing will be performed. 1. The first 1-byte data of the transmission data in the block is written into the transmit buffer register. 2. The data to be received next is processed as the first 1 byte of the received data in the block. Figure 2.4.37 shows a control procedure of the slave unit using the serial I/O1 receive interrupt and any timer interrupt (for heading adjustment).
Serial I/O1 receive interrupt processing routine
Timer interrupt processing routine
CLT (Note 1) CLD (Note 2) Push register to stack
Within a block transfer term? Y Read a reception data
* Push the register used in the interrupt processing routine into the stack. * Confirm the received byte counter to judge N the block transfer term.
CLT (Note 1) CLD (Note 2) Push register to stack
* Push the register used in the interrupt processing routine into the stack.
Heading adjustment counter - 1
Heading adjustment counter = 0? Y
N
A received byte counter +1
Write the first transmission data (first byte) in a block
A received byte counter 8? N
Y
A received byte counter
0
Pop registers Write a transmission data Write dummy data (FF16) RTI Heading adjustment counter Initial value (Note 3) * Pop registers which is pushed to stack.
* Pop registers which is pushed to stack.
Pop registers
RTI
Notes 1: When using the Index X mode flag (T). 2: When using the Decimal mode flag (D). 3: In this example, set the value which is equal to the heading adjustment time divided by the timer interrupt cycle as the initial value of the heading adjustment counter. For example: When the heading adjustment time is 8 ms and the timer interrupt cycle is 1 ms, set 8 as the initial value.
Fig. 2.4.37 Control procedure of slave unit
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-74
APPLICATION 3804 Group (Spec.H) 2.4 Serial interface
(4) Communication (transmit/receive) using asynchronous serial I/O (UART) Outline : 2-byte data is transmitted and received, using the asynchronous serial I/O. Port P40 is used for communication control. Figure 2.4.38 shows a connection diagram, and Figure 2.4.39 shows a timing chart.
Transmitting side
P40
Receiving side
P40
TXD
RXD
3804 group (Spec. H)
3804 group (Spec. H)
Fig. 2.4.38 Connection diagram (Communication using UART)
Specifications : * Serial I/O1 is used (UART is selected). * Transfer bit rate : 9600 bps (f(XIN) = 4.9152 MHz is divided by 512) * Communication control using port P40 (The output level of port P40 is controlled by software.) * 2-byte data is transferred from the transmitting side to the receiving side at intervals of 10 ms generated by the timer.
P40
****
TXD1
ST D0 D1 D2 D3 D4 D5 D6 D7 SP(2) ST D0 D1 D2 D3 D4 D5 D6 D7 SP(2) ST D0
****
10 ms
Fig. 2.4.39 Timing chart (using UART)
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-75
APPLICATION 3804 Group (Spec.H) 2.4 Serial interface
Table 2.4.4 shows setting examples of the baud rate generator (BRG) values and transfer bit rate values; Figure 2.4.40 shows registers setting relevant to the transmitting side; Figure 2.4.41 shows registers setting relevant to the receiving side. Table 2.4.4 Setting examples of Baud rate generator (BRG) values and transfer bit rate values BRG count source (Note 1) f(XIN)/4 f(XIN)/4 f(XIN)/4 f(XIN)/4 f(XIN)/4 f(XIN)/4 f(XIN)/4 f(XIN)/4 f(XIN) f(XIN) f(XIN) BRG setting value 255(FF16) 127(7F16) 63(3F16) 31(1F16) 15(0F16) 7(0716) 3(0316) 1(0116) 3(0316) 1(0116) 0(0016) Transfer bit rate (bps) (Note 2) at f(XIN) = 4.9152 MHZ at f(XIN) = 16 MHZ 300 600 1200 2400 4800 9600 19200 38400 76800 153600 307200 976.5625 1953.125 3906.25 7812.5 15625 31250 62500 125000 250000 500000 1000000
Notes 1: Select the BRG count source with bit 0 of the serial I/O1 control register (Address : 001A16). 2: Equation of transfer bit rate: Transfer bit rate (bps) = f(XIN) (BRG setting value + 1) 16 m
m: When bit 0 of the serial I/O1 control register (Address : 001A16) is set to "0," a value of m is 1. When bit 0 of the serial I/O1 control register (Address : 001A16) is set to "1," a value of m is 4.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-76
APPLICATION 3804 Group (Spec.H) 2.4 Serial interface
Transmitting side
Serial I/O1 status register (Address : 001916)
b7 b0
SIO1STS
Transmit buffer empty flag * Confirm that the data has been transferred from Transmit buffer register to Transmit shift register. * When this flag is "1", it is possible to write the next transmission data in to Transmit buffer register. Transmit shift register shift completion flag Confirm completion of transmitting 1-byte data with this flag. "1" : Transmit shift completed
Serial I/O1 control register (Address : 001A16)
b7 b0
SIO1CON 1 0 0 1
001
BRG count source : f(XIN)/4 Synchronous clock : BRG/16 SRDY1 output disabled Transmit enabled Receive disabled Asynchronous serial I/O(UART) Serial I/O1 enabled
UART1 control register (Address : 001B16)
b7 b0
UART1CON
01
00
Character length : 8 bits Parity checking disabled Stop bit length : 2 stop bits P45/TXD1 pin : CMOS output
Baud rate generator 1 (Address : 001C16)
b7 b0
BRG1
8-1
Set
f(XIN) Transfer bit rate 16 m
-1
When bit 0 of Serial I/O1 control register (Address : 001A16) is set to "0," a value of m is 1. When bit 0 of Serial I/O1 control register (Address : 001A16) is set to "1," a value of m is 4.
Port P4 (Address : 000816)
b7 b0
P4
0
Port P40: Communication control: "H" active
Port P4 direction register (Address : 000916)
b7 b0
P4D
1
Port P40: Communication control: Output mode
Fig. 2.4.40 Registers setting relevant to transmitting side
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-77
APPLICATION 3804 Group (Spec.H) 2.4 Serial interface
Receiving side
Serial I/O1 status register (Address : 001916)
b7 b0
SIO1STS
Receive buffer full flag Confirm completion of receiving 1-byte data with this flag. "1" : at completing reception "0" : at reading out contents of Receive buffer register Overrun error flag "1" : When data is ready in Receive shift register while Receive buffer register contains the data. Parity error flag "1" : When a parity error occurs in enabled parity. Framing error flag "1" : When stop bits cannot be detected at the specified timing Summing error flag "1" : when any one of the following errors occurs. * Overrun error * Parity error * Framing error
Serial I/O1 control register (Address : 001A16)
b7 b0
SIO1CON
1010
001
BRG count source : f(XIN)/4 Synchronous clock : BRG/16
SRDY1 output disabled
Transmit disabled Receive enabled Asynchronous serial I/O(UART) Serial I/O1 enabled
UART1 control register (Address : 001B16)
b7 b0
UART1CON
1
0
0
Character length : 8 bits Parity checking disabled Stop bit length : 2 stop bits
Baud rate generator 1 (Address : 001C16)
b7 b0
BRG1
8-1
Set
f(XIN) Transfer bit rate 16 m
-1
When bit 0 of Serial I/O1 control register (Address : 001A16) is set to "0," a value of m is 1. When bit 0 of Serial I/O1 control register (Address : 001A16) is set to "1," a value of m is 4.
Port P4 direction register (Address : 000916)
b7 b0
P4D
0
Port P40: Communication control: Input mode
Fig. 2.4.41 Registers setting relevant to receiving side
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-78
APPLICATION 3804 Group (Spec.H) 2.4 Serial interface
Figure 2.4.42 shows a control procedure of the transmitting side, and Figure 2.4.43 shows a control procedure of the receiving side.
RESET
q X: This bit is not used here. Set it to "0" or "1" arbitrarily.
Initialization SIO1CON (Address : 001A16) 1001X0012 UART1CON (Address : 001B16) 000010002 BRG1 (Address : 001C16) 8-1 0 P4 (Address : 000816), bit0 P4D (Address : 000916) XXXXXXX12
... ..
* Port P40 set for communication control
Pass 10 ms? Y P4 (Address : 000816), bit0 TB1/RB1 (Address : 001816) 1
N
* An interval of 10 ms generated by Timer
* Communication start * Transmission data write Transmit buffer empty flag is set to "0" by this writing. * Judgment of transferring data from Transmit buffer register to Transmit shift register (Transmit buffer empty flag)
The first byte of a transmission data
SIO1STS (Address : 001916), bit0? 1 TB1/RB1 (Address : 001816) The second byte of a transmission data
0
* Transmission data write Transmit buffer empty flag is set to "0" by this writing. * Judgment of transferring data from Transmit buffer register to Transmit shift register (Transmit buffer empty flag)
SIO1STS (Address : 001916), bit0? 1
0
SIO1STS (Address : 001916), bit2?
1
0
* Judgment of shift completion of Transmit shift register (Transmit shift register shift completion flag)
P4 (Address : 000816), bit0
0
* Communication completion
Fig. 2.4.42 Control procedure of transmitting side
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-79
APPLICATION 3804 Group (Spec.H) 2.4 Serial interface
RESET Initialization SIO1CON (Address : 001A16) UART1CON (Address : 001B16) BRG1 (Address : 001C16) P4D (Address : 000916)
... ..
q X: This bit is not used here. Set it to "0" or "1" arbitrarily.
1010X0012 000010002 8-1 XXXXXXX02
SIO1STS (Address : 001916), bit1?
1
0
* Judgment of completion of receiving (Receive buffer full flag) * Reception of the first byte data Receive buffer full flag is set to "0" by reading data.
Read out a reception data from RB1 (Address : 001816)
SIO1STS (Address : 001916), bit6? 0
1
* Judgment of an error flag
SIO1STS (Address : 001916), bit1?
1
0
* Judgment of completion of receiving (Receive buffer full flag) * Reception of the second byte data Receive buffer full flag is set to "0" by reading data.
Read out a reception data from RB1 (Address : 001816)
SIO1STS (Address : 001916), bit6? 0
1
* Judgment of an error flag Processing for error
1
P4 (Address : 000816), bit0?
0
SIO1CON (Address : 001A16) SIO1CON (Address : 001A16)
0000X0012 1010X0012
* Countermeasure for a bit slippage
Fig. 2.4.43 Control procedure of receiving side
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-80
APPLICATION 3804 Group (Spec.H) 2.4 Serial interface
2.4.8 Notes on serial interface (1) Notes when selecting clock synchronous serial I/O Stop of transmission operation As for serial I/Oi (i = 1, 3) that can be used as either a clock synchronous or an asynchronous (UART) serial I/O, clear the serial I/Oi enable bit and the transmit enable bit to "0" (serial I/Oi and transmit disabled). q Reason Since transmission is not stopped and the transmission circuit is not initialized even if only the serial I/Oi enable bit is cleared to "0" (serial I/Oi disabled), the internal transmission is running (in this case, since pins TxDi, RxDi, SCLKi, and SRDYi function as I/O ports, the transmission data is not output). When data is written to the transmit buffer register in this state, data starts to be shifted to the transmit shift register. When the serial I/Oi enable bit is set to "1" at this time, the data during internally shifting is output to the TxDi pin and an operation failure occurs. Stop of receive operation As for serial I/Oi (i = 1, 3) that can be used as either a clock synchronous or an asynchronous (UART) serial I/O, clear the receive enable bit to "0" (receive disabled), or clear the serial I/Oi enable bit to "0" (serial I/Oi disabled). Stop of transmit/receive operation As for serial I/Oi (i = 1, 3) that can be used as either a clock synchronous or an asynchronous (UART) serial I/O, clear both the transmit enable bit and receive enable bit to "0" simultaneously (transmit and receive disabled) in the clock synchronous serial I/O mode. (When data is transmitted and received in the clock synchronous serial I/O mode, any one of data transmission and reception cannot be stopped.) q Reason In the clock synchronous serial I/O mode, the same clock is used for transmission and reception. If any one of transmission and reception is disabled, a bit error occurs because transmission and reception cannot be synchronized. In this mode, the clock circuit of the transmission circuit also operates for data reception. Accordingly, the transmission circuit does not stop by clearing only the transmit enable bit to "0" (transmit disabled). Also, the transmission circuit is not initialized by clearing the serial I/Oi enable bit to "0" (serial I/Oi disabled) (refer to in (1) ). (2) Notes when selecting clock asynchronous serial I/O Stop of transmission operation Clear the transmit enable bit to "0" (transmit disabled). Transmission operation does not stop by setting the serial I/Oi enable bit (i = 1, 3) to "0". q Reason This is the same as in (1). Stop of receive operation Clear the receive enable bit to "0" (receive disabled).
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-81
APPLICATION 3804 Group (Spec.H) 2.4 Serial interface
Stop of transmit/receive operation Only transmission operation is stopped. Clear the transmit enable bit to "0" (transmit disabled). Transmission operation does not stop by setting the serial I/Oi enable bit (i = 1, 3) to "0". q Reason This is the same as in (1). Only receive operation is stopped. Clear the receive enable bit to "0" (receive disabled). (3) SRDYi (i = 1, 3) output of reception side When signals are output from the SRDYi pin on the reception side by using an external clock in the clock synchronous serial I/O mode, set all of the receive enable bit, the SRDYi output enable bit, and the transmit enable bit to "1" (transmit enabled). (4) Setting serial I/Oi (i = 1, 3) control register again Set the serial I/Oi control register again after the transmission and the reception circuits are reset by clearing both the transmit enable bit and the receive enable bit to "0."
Clear both the transmit enable bit (TE) and the receive enable bit (RE) to "0" Set the bits 0 to 3 and bit 6 of the serial I/Oi control register Set both the transmit enable bit (TE) and the receive enable bit (RE), or one of them to "1"
Can be set with the LDM instruction at the same time
Fig. 2.4.44 Sequence of setting serial I/Oi (i = 1, 3) control register again (5) Data transmission control with referring to transmit shift register completion flag After the transmit data is written to the transmit buffer register, the transmit shift register completion flag changes from "1" to "0" with a delay of 0.5 to 1.5 shift clocks. When data transmission is controlled with referring to the flag after writing the data to the transmit buffer register, note the delay. (6) Transmission control when external clock is selected When an external clock is used as the synchronous clock for data transmission, set the transmit enable bit to "1" at "H" of the SCLKi (i = 1, 3) input level. Also, write the transmit data to the transmit buffer register at "H" of the SCLKi input level.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-82
APPLICATION 3804 Group (Spec.H) 2.4 Serial interface
(7) Transmit interrupt request when transmit enable bit is set When the transmit interrupt is used, take the following sequence. Set the serial I/Oi transmit interrupt enable bit (i = 1, 3) to "0" (disabled). Set the tranasmit enable bit to "1". Set the serial I/Oi transmit interrupt request bit (i = 1, 3) to "0" after 1 or more instruction has executed. Set the serial I/Oi transmit interrupt enable bit (i = 1, 3) to "1" (enabled). q Reason When the transmission enable bit is set to "1", the transmit buffer empty flag and transmit shift register shift completion flag are also set to "1". Therefore, regardless of selecting which timing for the generating of transmit interrupts, the interrupt request is generated and the transmit interrupt request bit is set at this point. (8) Writing to baud rate generator i (BRGi) (i = 1, 3) Write data to the baud rate generator i (BRGi) (i = 1, 3) while the transmission/reception operation is stopped.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-83
APPLICATION 3804 Group (Spec.H) 2.5 Multi-master I2C-BUS interface
2.5 Multi-master I2C-BUS interface
The only 3804 group has functions of the multi-master I 2C-BUS interface. The multi-master I2C-BUS interface is a serial communication circuit, conforming to the Philips I2C-BUS data transfer format. This paragraph explains the I 2C-BUS overview and communication examples. 2.5.1 Memory map
001016 MISRG 001116 I2C data shift register (S0) 001216 I2C special mode status register (S3) 001316 I2C status register (S1) 001416 I2C control register (S1D) 001516 I2C clock control register (S2) 001616 I2C START/STOP condition control register (S2D) 001716 I2C special mode control register (S3D) 003916 Interrupt source selection register (INTSEL)
003C16 Interrupt request register 1 (IREQ1) 003D16 Interrupt request register 2 (IREQ2) 003E16 Interrupt control register 1 (ICON1) 003F16 Interrupt control register 2 (ICON2) 0FF716 0FF816 I2C slave address register 0 (S0D0) I2C slave address register 1 (S0D1)
0FF916 I2C slave address register 2 (S0D2)
Fig. 2.5.1 Memory map of registers relevant to I 2C-BUS interface
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-84
APPLICATION 3804 Group (Spec.H) 2.5 Multi-master I2C-BUS interface
2.5.2 Relevant registers
MISRG
b7 b6 b5 b4 b3 b2 b1 b0 MISRG (MISRG: address 001016)
b
Name
Functions
At reset R W
0
0 Oscillation stabilizing 0: Automatically set (Note 1) time set after STP 1: Autimatically set disabled instruction released bit 1 Middle-speed mode 0: Not set automatically automatic switch set 1: Automatic switching enabled (Notes 2, 3) bit 2 Middle-speed mode 0: 4.5 to 5.5 machine cycles 1: 6.5 to 7.5 machine cycles automatic switch wait time set bit 3 Middle-speed mode 0: Invalid 1: Automatic switch start automatic switch (Note 3) start bit (Depending on program) 4 Nothing is arranged for these bits. These are write disabled bits. When these bits are read 5 out, the contents are 0 . 6
0
0
0
0 0 0
0 7 Notes 1: 0116 is set to Timer 1, FF16 is set to Prescaler 12. 2: During operation in low-speed mode, it is possible automatically to switch to middle-speed mode owing to the rising of SCL/SDA. 3: When automatic switch to middle-speed mode from low-speed mode occurs, the values of CPU mode register (003B16) change.

Fig. 2.5.2 Structure of MISRG
I2C data shift register
b7 b6 b5 b4 b3 b2 b1 b0 I2C data shift register (S0: address 001116)
b
Functions
At reset R W
0 * 8-bit shift register to store receive data and 1 write transmit data. 2 3 4 5 6 7
Undefined Undefined Undefined Undefined Undefined Undefined Undefined Undefined Note: When data is written to I2C data shift register after the MST bit is set to "0" (slave mode), keep the interval for 8 machine cycles or more. Also, when the read-modify-write instructions (SEB, CLB) are used during data transfer, the values may be undefined.
Fig. 2.5.3 Structure of I 2C data shift register
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-85
APPLICATION 3804 Group (Spec.H) 2.5 Multi-master I2C-BUS interface
I2C special mode status register
b7 b6 b5 b4 b3 b2 b1 b0 I2C special mode status register (S3: address 001216)
b
Name
Functions
0: Address disagreement 1: Address agreement (Notes 1, 2) 0: Address disagreement 1: Address agreement (Notes 1, 2) 0: Address disagreement 1: Address agreement (Notes 1, 2)
0 Slave address 0 comparison flag (AAS0) 1 Slave address 1 comparison flag (AAS1) 2 Slave address 2 comparison flag (AAS2)
At reset R W 0
0
0
3 Nothing is arranged for this bit. This is a write disabled bit. When this bit is read out, the contents are 0 . 4 Nothing is arranged for this bit. This is a write disabled bit. When this bit is read out, the contents are undefined. 5 SCL pin low hold 2 0: SCL pin low hold 1: SCL pin low release flag (PIN2) (Notes 1, 3) 6 Nothing is arranged for this bit. This is a write disabled bit. When this bit is read out, the contents are 0 . 7 STOP condition flag (SPCF) 0: No detection 1: Detection (Notes 1, 4)
0

0
1
0

0
Notes 1: These bits and flags can be read out, but cannot be written. 2: These bits can be detected only when the data format selection bit (ALS) of I2C control register is set to 0 . 3: This bit is initialized to 1 at reset, when the ACK interrupt control bit is 0 , or when writing 1 to the SCL pin low hold 2 flag set bit. 4: This bit is initialized to 0 at reset, when the I2C-BUS interface enable bit (ES0) is 0 , or when writing 1 to the STOP condition flag clear bit.
Fig. 2.5.4 Structure of I 2C special mode status register
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-86
APPLICATION 3804 Group (Spec.H) 2.5 Multi-master I2C-BUS interface
I2C status register
b7 b6 b5 b4 b3 b2 b1 b0 I2C status register (S1: address 001316)
b
Name
Functions
At reset R W
0 Last receive bit (LRB) 1 General call detection flag (AD0) 2 Slave address comparison flag (AAS) 3 Arbitration lost detection flag (AL) 4 SCL pin low hold bit (PIN) 5 Bus busy flag (BB) 6 Communication mode specification bits (TRX, MST) 7
Undefined 0: Last bit = 0 1: Last bit = 1 (Note 1) 0 0: No general call detected 1: General call detected (Notes 1, 2) 0 0: Address disagreement 1: Address agreement (Notes 1, 2) 0: Not detected 1: Detected (Note 1) 0: SCL pin low hold (Note 3) 1: SCL pin low release 0: Bus free 1: Bus busy
b7 b6
0 1 0 0
0 0 1 1
0: 1: 0: 1:
Slave receive mode Slave transmit mode Master receive mode Master transmit mode
0
Notes 1: These flags and bits are exclusive to input. When writing to these bits, write 0 to these bits. 2: These bits can be detected only when the data format selection bit (ALS) of I2C control register is set to 0 . 3: This bit can be set to 1 by program, but cannot be cleared to 0 . 4: All bits are changed by hardware. Do not use the readmodify-write instructions (SEB, CLB).
Fig. 2.5.5 Structure of I 2C status register
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-87
APPLICATION 3804 Group (Spec.H) 2.5 Multi-master I2C-BUS interface
I2C control register
b7 b6 b5 b4 b3 b2 b1 b0 I2C control register (S1D: address 001416)
b
Name
b2b1b0
Functions
0 0 0: 8 0 0 1: 7 0 1 0: 6 0 1 1: 5 1 0 0: 4 1 0 1: 3 1 1 0: 2 1 1 1: 1
At reset R W
0 0 0 0 0 0
0 Bit counter (Number of transmit/receive 1 bits) (BC0, BC1, BC2) 2
0: Disabled 3 I2C-BUS interface 1: Enabled enable bit (ES0) 0: Addressing format 4 Data format selection bit (ALS) 1: Free data format 5 Addressing format 0: 7-bit addressing format selection bit 1: 10-bit addressing format (10BIT SAD) 6 Nothing is arranged for this bit. This is a write disabled bit. When this bit is read out, the contents are 0 . 7 I2C-BUS interface pin 0: SMBUS input input level selection 1: CMOS input bit (TISS)
0
0
Note: Do not use the read-modify-write instruction because some bits change by hardware when the start condition is detected and the byte-transfer is completed.
Fig. 2.5.6 Structure of I 2C control register
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-88
APPLICATION 3804 Group (Spec.H) 2.5 Multi-master I2C-BUS interface
I2C clock control register
b7 b6 b5 b4 b3 b2 b1 b0 I2C clock control register (S2: address 001516)
b
Name
Functions
Setting value b4b3b2b1b0 00 to 02 03 04 05 06 Standard High-speed clock mode clock mode Disabled Disabled Disabled 333 (Note 2) 250 100 400 (Note 3) 83.3 166 500/CCR value 1000/CCR value (Note 3) (Note 3) 17.2 34.5 1D 1E 16.6 33.3 1F 16.1 32.3 ( = 4 MHz, Unit: kHz) (Note 1)
At reset R W
0 0 0 0 0 0
0 SCL frequency control bits (CCR0, CCR1, 1 CCR2, CCR3, CCR4) 2 3 4 5 SCL mode specification bit (FAST MODE) 6 ACK bit (ACK BIT) 7 ACK clock bit (ACK)
0: Standard clock mode 1: High-speed clock mode 0: ACK is returned. 1: ACK is not returned. 0: No ACK clock 1: ACK clock
0 0
Notes 1: Duty of SCL clock output is 50 %. The duty becomes 35 to 45 % only when the highspeed clock mode is selected and CCR value = 5 (400 kHz, at = 4 MHz). H duration of the clock fluctuates from --4 to +2 machine cycles in the standard clock mode, and fluctuates from --2 to +2 machine cycles in the high-speed clock mode. In the case of negative fluctuation, the frequency does not increase because L duration is extended instead of H duration reduction. These are values when SCL clock synchronization by the synchronous function is not performed. CCR value is the decimal notation value of the SCL frequency control bits CCR4 to CCR0. 2: Each value of SCL frequency exceeds the limit at = 4 MHz or more. When using these setting value, use of 4 MHz or less. 3: The data formula of SCL frequency is described below: /(8 CCR value) Standard clock mode /(4 CCR value) High-speed clock mode (CCR value 5) /(2 CCR value) High-speed clock mode (CCR value = 5) Do not set 0 to 2 as CCR value regardless of frequency. Set 100 kHz (max.) in the standard clock mode and 400 kHz (max.) in the high-speed clock mode to the SCL frequency by setting the SCL frequency control bits CCR4 to CCR0.
Fig. 2.5.7 Structure of I 2C clock control register
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-89
APPLICATION 3804 Group (Spec.H) 2.5 Multi-master I2C-BUS interface
I2C START/STOP condition control register
b7 b6 b5 b4 b3 b2 b1 b0
0
I2C START/STOP condition control register (S2D: address 001616)
b
Name
Functions
SCL release time = (s) (SSC+1) Setup time = (s) (SSC+1)/2 Hold time = (s) (SSC+1)/2
At reset R W
0 1 0 1 1
0 START/STOP condition set bits 1 (SSC0, SSC1, 2 SSC2, SSC3, SSC4) 3 4 5 SCL/SDA interrupt pin polarity selection bit (SIP) 6 SCL/SDA interrupt pin selection bit (SIS) 7 Fix this bit to 0 .
0: Falling edge active 1: Rising edge active 0: SDA valid 1: SCL valid
0
0
0
Note: Fix SSC0 to 0 . Also, do not set SSC4 to SSC0 to odd values or 000002 .
Fig. 2.5.8 Structure of I 2C START/STOP condition control register
I2C special mode control register
b7 b6 b5 b4 b3 b2 b1 b0
0
0
I2C special mode control register (S3D: address 001716)
b
Name
Functions
At reset R W
0 0
0 Fix this bit to 0 . 1 ACK interrupt control 0: At communication completion bit (ACKICON) 1: At falling of ACK clock and communication completion 2 Slave address 0: One-byte slave address control bit (MSLAD) compare mode 1: Three-byte slave address compare mode 3 Nothing is arranged for this bit. This is a write disabled bit. When this bit is read out, the contents are 0 . 4 Fix this bit to 0 . 5 SCL pin low hold 2 Writing 1 to this bit initializes flag set bit (PIN2IN) the SCL pin low hold 2 flag to 1 . (Notes 1, 2) Writing 1 to this bit clears 6 SCL pin low hold set bit (PIN2HD) the SCL pin low hold 2 flag to 0 and holds the SCL pin low. (Notes 1, 2) 7 STOP condition flag Writing 1 to this bit initializes clear bit (SPFCL) the STOP condition flag to 0 . (Note 1)
0
0
0 0
0
0
Notes 1: When 0 is written to these bits, nothing is happened. 2: Do not write 1 to these bits at the same time.
Fig. 2.5.9 Structure of I2C special mode control register
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-90
APPLICATION 3804 Group (Spec.H) 2.5 Multi-master I2C-BUS interface
I2C slave address register i (i = 0 to 2)
b7 b6 b5 b4 b3 b2 b1 b0 I2C slave address register i (i = 0 to 2) (S0D0, S0D1, S0D2: addresses 0FF716, 0FF816, 0FF916)
b
Name
Functions
0: Write bit 1: Read bit
At reset R W
0
0 Read/Write bit (RWB)
1 Slave address 0 The contents of these bits 2 (SAD0, SAD1, SAD2, are compared with the 0 3 SAD3, SAD4, SAD5, address data transmitted 0 from master. 4 SAD6) 0 5 0 6 0 7 0 Note: When the read-modify-write instructions (SEB, CLB) are used at detection of stop condition, the values may be undefined.
Fig. 2.5.10 Structure of I 2C slave address register i (i = 0 to 2)
Interrupt source selection register
b7 b6 b5 b4 b3 b2 b1 b0 Interrupt source selection register (INTSEL: address 003916)
b
Name
Functions
0: INT0 interrupt 1: Timer Z interrupt 0: Serial I/O2 interrupt 1: Timer Z interrupt 0: Serial I/O1 transmit interrupt 1: SCL, SDA interrupt 0: CNTR0 interrupt 1: SCL, SDA interrupt 0: INT4 interrupt 1: CNTR2 interrupt 0: INT2 interrupt 1: I2C interrupt 0: CNTR1 interrupt 1: Serial I/O3 receive interrupt 0: A/D converter interrupt 1: Serial I/O3 transmit interrupt
At reset R W
0
0 INT0/Timer Z interrupt source selection bit (*1) 1 Serial I/O2/Timer Z interrupt source selection bit (*1) 2 Serial I/O1 transmit/ SCL, SDA interrupt source selection bit (*2) 3 CNTR0/SCL, SDA interrupt source selection bit (*2) 4 INT4/CNTR2 interrupt source selection bit 5 INT2/I2C interrupt source selection bit 6 CNTR1/Serial I/O3 receive interrupt source selection bit 7 AD converter/Serial I/O3 transmit interrupt source selection bit
0
0
0
0
0 0
0
*1: Do not write 1 to these bits simultaneously. *2: Do not write 1 to these bits simultaneously.
Fig. 2.5.11 Structure of Interrupt source selection register
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-91
APPLICATION 3804 Group (Spec.H) 2.5 Multi-master I2C-BUS interface
Interrupt request register 1
b7 b6 b5 b4 b3 b2 b1 b0 Interrupt request register 1 (IREQ1 : address 003C16)
b
Name
Functions
At reset R W
0 0 0 0
0 INT0/Timer Z 0 : No interrupt request issued interrupt request bit 1 : Interrupt request issued 1 INT1 interrupt request bit
0 : No interrupt request issued
1 : Interrupt request issued
2 Serial I/O1 receive 0 : No interrupt request issued interrupt request bit 1 : Interrupt request issued
0 : No interrupt request issued 3 Serial I/O1 transmit/SCL, SDA 1 : Interrupt request issued interrupt request bit
4 Timer X interrupt request bit 5 Timer Y interrupt request bit 6 Timer 1 interrupt request bit
0 : No interrupt request issued
0 0 0 0

1 : Interrupt request issued
0 : No interrupt request issued
1 : Interrupt request issued
0 : No interrupt request issued
1 : Interrupt request issued
7 Timer 2 interrupt 0 : No interrupt request issued request bit 1 : Interrupt request issued : 0 can be set by software, but 1 cannot be set.
Fig. 2.5.12 Structure of Interrupt request register 1
Interrupt request register 2
b7 b6 b5 b4 b3 b2 b1 b0 Interrupt request register 2 (IREQ2 : address 003D16)
b
Name
Functions
At reset R W
0 0
0 CNTR0/SCL, SDA 0 : No interrupt request issued interrupt request bit 1 : Interrupt request issued 1 CNTR1/Serial I/O3 0 : No interrupt request issued 1 : Interrupt request issued receive interrupt request bit 2 Serial I/O2/Timer Z interrupt request bit 3 INT2/I2C interrupt request bit 4 INT3 interrupt request bit 5 INT4/CNTR2 interrupt request bit 6 AD converter/Serial I/O3 transmit interrupt request bit 0 : No interrupt request issued 1 : Interrupt request issued 0 : No interrupt request issued 1 : Interrupt request issued 0 : No interrupt request issued 1 : Interrupt request issued 0 : No interrupt request issued 1 : Interrupt request issued 0 : No interrupt request issued 1 : Interrupt request issued
0 0 0 0 0

7 Nothing is arranged for this bit. This is a write disabled bit. When this bit is read out, the contents are 0 . : 0 can be set by software, but 1 cannot be set.
0
Fig. 2.5.13 Structure of Interrupt request register 2
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-92
APPLICATION 3804 Group (Spec.H) 2.5 Multi-master I2C-BUS interface
Interrupt control register 1
b7 b6 b5 b4 b3 b2 b1 b0 Interrupt control register 1 (ICON1 : address 003E16)
b
Name
Functions
0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled
At reset R W
0 0 0 0
0 INT0/Timer Z interrupt enable bit 1 INT1 interrupt enable bit 2 Serial I/O1 receive interrupt enable bit 3 Serial I/O1 transmit/SCL, SDA interrupt enable bit 4 Timer X interrupt enable bit 5 Timer Y interrupt enable bit 6 Timer 1 interrupt enable bit 7 Timer 2 interrupt enable bit
0 0 0 0
Fig. 2.5.14 Structure of Interrupt control register 1
Interrupt control register 2
b7 b6 b5 b4 b3 b2 b1 b0
0
Interrupt control register 2 (ICON2 : address 003F16)
b
Name
Functions
0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled
At reset R W
0 0
0 CNTR0/SCL, SDA interrupt enable bit 1 CNTR1/ Serial I/O3 receive interrupt enable bit 2 Serial I/O2/ Timer Z interrupt enable bit 3 INT2/I2C interrupt enable bit 4 INT3 interrupt enable bit 5 INT4/CNTR2 interrupt enable bit 6 AD converter/Serial I/O3 transmit interrupt enable bit 7 Fix this bit to 0 .
0 0 0 0 0
0
Fig. 2.5.15 Structure of Interrupt control register 2
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-93
APPLICATION 3804 Group (Spec.H) 2.5 Multi-master I2C-BUS interface
2.5.3 I 2C-BUS overview The I 2C-BUS is a both directions serial bus connected with two signal lines; the SCL which transmits a clock and the SDA which transmits data. Each port of the 3804 group has an N-channel open-drain structure for output and a CMOS structure for input. The devices connected with the I 2 C-BUS interface use an open drain, so that external pull-up resistors are required. Accordingly, while any one of devices always outputs "L", other devices cannot output "H". Figure 2.5.16 shows the I 2C-BUS connection structure.
SCL output
SCL output
SCL input
SCL input
SDA output
SDA output
SDA input
SDA input
SCL output
SCL input
SDA output
SDA input
Fig. 2.5.16 I 2C-BUS connection structure
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-94
APPLICATION 3804 Group (Spec.H) 2.5 Multi-master I2C-BUS interface
2.5.4 Communication format Figure 2.5.17 shows an I2C-BUS communication format example. The I 2C-BUS consists of the following: *START condition to indicate communication start *Slave address and data to specify each device *ACK to indicate acknowledgment of address and data *STOP condition to indicate communication completion.
Bus busy term S Slave address 7 bits R/W A Data 8 bits A Data 8 bits AP
SCL
SDA Start Addresses 0 to 6 W ACK Data 0 to 7 ACK Data 0 to 7 ACK Stop
Fig. 2.5.17 I2C-BUS communication format example (1) START condition When communication starts, the master device outputs the START condition to the slave device. The I2C-BUS defines that data can be changed when a clock line is "L". Accordingly, data change when a clock line is "H" is treated as STOP or START condition. The data line change from "H" to "L" when a clock line is "H" is START condition. (2) STOP condition Just as in START condition, the data line change from "L" to "H" when a clock line is "H" is STOP condition. The term from START condition to STOP condition is called "Bus busy". The master device is inhibited from starting data transfer during that term. The Bus busy status can be judged by using the BB flag of I2C status register (bit 5 of address 001316). (3) Slave address The slave address is transmitted after START condition. This address consists of 7 bits and the 7th bit functions as the read/write (R/W) bit which indicates a data transmission method. The slave devices connected with the same I2C-BUS must have their addresses, individually. It is because that address is defined for the master to specify the transmitted/received slave device. The read/write (R/W) bit indicates a data transmission direction; "L" means write from the master to the slave, and "H" means read in. (4) Data The data has an 8-bit length. There are two cases depending on the read/write (R/W) bit of a slave address; one is from the master to the slave and the other is from the slave to the master.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-95
APPLICATION 3804 Group (Spec.H) 2.5 Multi-master I2C-BUS interface
(5) ACK bit The ACK bit clock is generated by the master. This is used for indication of acknowledgment on the SDA line, the slave's busy and the data end. For example, the slave device makes the SDA line "L" for acknowledgment when confirming the slave address following the START condition. The built-in I2C-BUS interface has the slave address automatic judgment function and the ACK acknowledgment function. "L" is automatically output when the ACK bit of I2C clock control register (bit 6 of address 001516) is "0" and an address data is received. When the slave address and the address data do not correspond, "H" (NACK) is automatically output. In case the slave device cannot receive owing to an interrupt process, performing operation or others, the master can output STOP condition and complete data transfer by making the ACK data of the slave address "H" for acknowledgment. Even in case the slave device cannot receive data during data transferring, the communication can be interrupted by performing NACK acknowledgment to the following data. When the master is receiving the data from the slave, the master can notify the slave of completion of data reception by performing NACK acknowledgment to the last data received from the slave. (6) RESTART condition The master can receive or transmit data without transmission of STOP condition while the master is transmitting or receiving a data. For example, after the master transmitted a data to the slave, transmitting a slave address + R (Read) following RESTART condition can make the following data treat as a reception data. Additionally, transmitting a slave address + W (Write) following RESTART condition can make the following data treat as a transmission data.
START condition
RESTART condition
Master reception 1st-byte
Master reception 2nd-byte
S
Slave address R/W A 7 bits "0" Write
Data 8 bits
A Sr
Slave address R/W A 7 bits "1" Read
Lower data 8 bits
A
Upper data 8 bits
AP
NACK expression end of master reception data S: START condition P: STOP condition A: ACK bit R/W: Read/Write bit Sr: RESTART condition Master to slave Slave to master
Fig. 2.5.18 RESTART condition of master reception 2.5.5 Synchronization and arbitration lost (1) Synchronization When a plural master exists on the I2C-BUS and the masters, which have different speed, are going to simultaneously communicate; there is a rule to unify clocks so that a clock of each bit can be output correctly. Figure 2.5.19 shows a synchronized SCL line example. The SCL (A) and the SCL (B) are the master devices having a different speed. The SCL is synchronized waveforms. As shown by Figure 2.5.19, the SCL lines can be synchronized by the following method; the device which first finishes "H" term makes the SCL line "L" and the device which last remains "L" makes the SCL line "H".
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-96
APPLICATION 3804 Group (Spec.H) 2.5 Multi-master I2C-BUS interface
SCL(A)
SCL(B)

SCL
Fig. 2.5.19 SCL waveforms when synchronizing clocks After START condition, the masters, which have different speed, simultaneously start clock transmission. The SCL outputs "L" because (A) finished counting "H" output; then (B)'s "H" output counting is interrupted and (B) starts counting "L" output. The (A) outputs "H" because (A) finished counting "L" term; the SCL level does not become "H" because (B) outputs "L", and counting "H" term does not start but stop. (B) outputs "L" term. The SCL outputs "H" because (B) finished counting "L" term; then (B)'s "H" output counting is started at the same time as (A). The SCL outputs "L" because (A) first finished counting "H" output; then (B)'s "H" output counting is interrupted and (B) starts counting "L" output. The above are repeatedly performed. (2) Clock synchronization during communication In the I 2C-BUS, the slave device is permitted to retain the SCL line "L" and become waiting status for transmission from the master. By byte unit, for the reception preparation of the slave device, the master can become waiting status by making the SCL line "L", which is after completion of byte reception or the ACK. By bit unit, it is possible to slow down a clock speed by retaining the clock line "L" for slave devices having limited hardware. The 3804 group can transmit data correctly without reduction of data bits toward waiting status request from the slave device. It is because the synchronization circuit is included for the case when retaining the SCL line "L" as an internal hardware. After the last bit, including the ACK bit, of a transmission/reception data byte, the SCL line automatically remains "L" and waiting status is generated until completion of an interrupt process or reception preparation. (3) Arbitration lost A plural master exists on the same bus in the I2C-BUS and there are possibility to start communication simultaneously. Even when the master devices having the same transmission frequency start communication simultaneously, which device must transmit data correctly. Accordingly, there is the definition to detect a communication confliction on the SDA line in the I 2C-BUS. The SDA line is output at the timing synchronized by the SCL, however, the synchronization among the SDA signals is not performed.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-97
APPLICATION 3804 Group (Spec.H) 2.5 Multi-master I2C-BUS interface
2.5.6 SMBUS communication usage example This clause explains a SMBUS communication control example using the I2C-BUS. This is a control example as the master device and the slave device in the Read Word protocol of SMBUS protocol. The following is a communication example of the "Voltage () command" of the Smart battery data. Communication specifications: *Communication frequency = 100 kHz *Slave address of itself, battery, = "0001011X2" (X means the read/write bit) *Slave address of communication destination, host, = "0001000X2" (X means the read/write bit) *Voltage () command = "0916" *Voltage value of acknowledgment = "2EE016" (12000 mV) *The communication process is performed in the interrupt process. However, the main process performs an occurrence of the first START condition and a slave address set. *A communication buffer is established. Data transfer between the main process and the interrupt process is performed through the communication buffer. (1) Initial setting Figure 2.5.20 shows an initial setting example using SMBUS communication.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-98
APPLICATION 3804 Group (Spec.H) 2.5 Multi-master I2C-BUS interface
I2C special mode control register (address 001716)
b7 b0
S3D
00000000 Fix to "0" ACK interrupt control : At communication completion One-byte slave address compare mode Fix to "0" Fix to "0" SCL pin low hold 2 flag set bit : Not used SCL pin low hold set bit : Not set STOP condition flag clear bit : Not used I2C slave address register 0 (address 0FF716)
b7 b0
This setting can be omitted.
S0D0
00010110 Set slave address value 001616. I2C clock control register (address 001516)
b7 b0
S2
10000101 Set clock 100 kHz (XIN = 8MHz) Standard clock mode ACK is returned ACK clock I2C status register (address 001316)
b7 b0
S1
00
1 SCL pin low hold bit: Fix to "1" Slave receive mode
I2C START/STOP condition control register (address 001616)
b7 b0
S2D
00011010 Set setup time, hold time to 27 cycles (6.75 s: XIN = 8 MHz). SCL/SDA interrupt: Falling edge active SCL/SDA interrupt: SDA valid Fix to "0"
I2C control register (address 001416)
b7 b0
S1D
00001000 Set number of transmit/receive bits to "8". I2C-BUS interface: Enabled Addressing format 7-bit addressing format Fix to "0" Set SMBUS input level.
Fig. 2.5.20 Initial setting example for SMBUS communication
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-99
APPLICATION 3804 Group (Spec.H) 2.5 Multi-master I2C-BUS interface
(2) Communication example in master device The master device follows the procedures to shown by Figure 2.5.21. Additionally, the shaded area in the figure is a transmission data from the master device and the white area is a transmission data from the slave device. Generating of START condition; Transmission of slave address + write bit Transmission of command Generating of RESTART condition; Transmission of slave address + read bit Reception of lower data Reception of upper data Generating of STOP condition
Figures 2.5.22 to 2.5.27 show the procedures to .

S
Slave address R/W A Command A Sr Slave address R/W A 7 bits "0" Write 8 bits 7 bits Interrupt request "1" Read
Lower data 8 bits
A
Upper data 8 bits
AP
Interrupt request
Interrupt request Interrupt request
Interrupt request
S: START condition P: STOP condition A: ACK bit R/W: Read/Write bit Sr: RESTART condition
Master to slave Slave to master
Fig. 2.5.21 Read Word protocol communication as SMBUS master device
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-100
APPLICATION 3804 Group (Spec.H) 2.5 Multi-master I2C-BUS interface
Generating of START condition; Transmission of slave address + write bit After confirming that other master devices do not use the bus, generate the START condition, because the SMBUS is a multi-master. Write "slave address + write bit" to the I2C data shift register (address 001116) before performing to make the START condition generate. It is because the SCL of 1-byte unit is output, following occurrence of the START condition. If other master devices start communication until an occurrence of the START condition after confirming the bus use, it cannot communicate correctly. However in this case, that situation does not affect other master devices owing to detection of an arbitration lost or the START condition duplication preventing function.
1
(A)000100002
SEI (Note 1)
* Interrupts disabled
1 (used) BB (address 001316), bit5 ? (Note 2) 0 (not used) S0 (address 001116) (A) S1 (address 001316) 111100002 * Slave address value write * START condition occurrence * Bus use confirmation
CLI (Note 1) End
* Interrupt enabled
Notes 1: In this example, the SEI instruction to disable interrupts need not be executed because this processing is going to be performed in the interrupt processing. When the START condition is generated out of the interrupt processing, execute the SEI instruction to disable interrupts. 2: Use the branch bit instruction to confirm bus busy.
Fig. 2.5.22 Generating of START condition and transmission process of slave address + write bit
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-101
APPLICATION 3804 Group (Spec.H) 2.5 Multi-master I2C-BUS interface
Transmission of command Confirm correct completion of communication at before command transmission. When receiving the STOP condition, a process not to transmit a command is required, because the internal I2CBUS generates an interrupt request also owing to the STOP condition transmitted to other devices. After confirming correct completion of communication, write a command to the I 2 C data shift register (address 001116). In case the AL bit (bit 3 of address 001316) is "1", check the slave address comparison flag (AAS bit; bit 2 of address 001316) to judge whether the device given a right of master transmission owing to an arbitration specifies itself as a slave address. When it is "1", perform the slave reception; when "0", wait for a STOP condition occurrence caused by other devices and the communication completion. In case the AL bit is "0", check the last received bit (LRB bit; bit 0 of address 001316). When it is "1", make the STOP condition generate and release the bus use, because the specified slave device does not exist on the SMBUS.
2
1(error) PIN (address 001316), bit 4 ?
* Judgment of bus hold
0 (slave address transmitted) 1(detected) AL (address 001316), bit 3 ? 0 (not detected) 1(NACK) LRB (address 001316), bit 0 ? 0 (ACK) S0 (address 001116) 000010012 * Command data write to I2C data shift register * ACK confirmation * Judgment of arbitration lost detection
End
STOP condition output
0 (address not corresponded) AAS (address 001316), bit 2 ? * Judgment of slave address comparison
1 (address corresponded) Re-transmission preparation Slave reception
Fig. 2.5.23 Transmission process of command
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-102
APPLICATION 3804 Group (Spec.H) 2.5 Multi-master I2C-BUS interface
Generating of RESTART condition; Transmission of slave address + read bit Confirm correct completion of communication at before generating the RESTART condition. After confirming correct completion, generate the RESTART condition and perform the transmission process of "slave address + read bit". Note that procedure because that is different from 's process. As the same reason as , write "slave address + read bit" to the I2C data shift register (address 001116) before performing to make the START condition generate. However, when writing a slave address to the I 2C data shift register in this condition, a slave address is output at that time. Consequently, the RESTART condition cannot be generated. Therefore, follow the slave reception procedure before those processes. In case the arbitration lost detecting flag (AL bit, bit 3 of address 001316) is "1", return to the process , because other master devices will have priority to communicate. When the last received bit (LRB bit; bit 0 of address 001316) is "1", generate the STOP condition and make the bus release, because acknowledgment cannot be done owing to BUSY status of the slave device specified on the SMBUS or other reasons.
3
1 (STOP condition)
PIN (address 001316), bit 4 ?
* Bus judgment during hold
0 (command transmission) 1 (detected) AL (address 001316), bit 3 ? 0 (not detected) 1 (NACK) LRB (address 001316), bit 0 ? 0 (ACK) S1 (address 001316) 000000002 (Note 1) (A) 000100012 * Slave receive mode set * ACK confirmation * Judgment of arbitration lost detection
* Slave address read out
SEI (Note 2) S0 (address 001116) (A) S1 (address 001316) 111100002
* Interrupt disabled
* Slave address value write * RESTART condition occurrence * Interrupt enabled
CLI (Note 2)
End
Re-transmission preparation
STOP condition output
Notes 1: Set to the receive mode while the PIN bit is "0". Do not write "1" to the PIN bit. 2: In this example, the SEI instruction to disable interrupts need not be executed because this processing is going to be performed in the interrupt processing. When the START condition is generated out of the interrupt processing, execute the SEI instruction to disable interrupts.
Fig. 2.5.24 Transmission process of RESTART condition and slave address + read bit
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-103
APPLICATION 3804 Group (Spec.H) 2.5 Multi-master I2C-BUS interface
Reception of lower data Confirm correct completion of communication at before receiving the lower data. After confirming correct completion, clear the ACK bit (bit 6 of address 001516) to "0", in which ACK is returned, and set to the master receive mode. After that, write dummy data to the I 2C data shift register (address 001116). When the MST bit (bit 7 of address 001316) is "0", perform the error process explained as follows and return to the process . When the last receive bit (LRB bit; bit 0 of address 001316) is "1", generate the STOP condition and make the bus release, because the slave device specified on the SMBUS does not exist.
4
1 (STOP condition) PIN (address 001316), bit 4 ? * Judgment of bus hold
0 (transmission of RESTART condition) 0 (slave) MST (address 001316), bit 7 ? 1 (master) 1 (NACK) LRB (address 001316), bit 0 ? 0 (ACK) S2 (address 001516) 100001012 S1 (address 001316) 101000002 S0 (address 001116) 111111112 * "ACK clock is used" select and "ACK is returned" set * Master receive mode set * Dummy data to I2C data shift register write * ACK confirmation * Judgment of slave mode detection
End
STOP condition output
1 (detected)
AL (address 001316), bit 3 ? 0 (not detected)
* Judgment of arbitration lost detection
Re-transmission preparation
Error processing
Fig. 2.5.25 Reception process of lower data
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-104
APPLICATION 3804 Group (Spec.H) 2.5 Multi-master I2C-BUS interface
Transmission of upper data Confirm correct completion of communication at before receiving the upper data. After confirming correct completion, store the received data (lower data). Set the ACK bit (bit 6 of address 001516) to "1", in which ACK is not returned and write dummy data to the I 2C data shift register (address 001116). When the MST bit (bit 7 of address 001316) is "0", return to the process , because other devices have priority to communicate.
5
1 (STOP condition) PIN (address 001316), bit 4 ? * Judgment of bus hold
0 (lower data transmitted) 0 (slave) MST (address 001316), bit 7 ? 1 (Master) Receive data buffer S0 (address 001116) S2 (address 001516) 110001012 S0 (address 001116) 111111112 * Receive data read and save * "NACK is returned" set * Dummy data to I2C data shift register write * Judgment of slave mode detection
End
1(detected)
AL (address 001316), bit 3 ? 0 (not detected)
* Judgment of arbitration lost detection
Re-transmission preparation
Error processing
Fig. 2.5.26 Reception process of upper data
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-105
APPLICATION 3804 Group (Spec.H) 2.5 Multi-master I2C-BUS interface
Generating of STOP condition Confirm correct completion of communication at before generating the STOP condition. After confirming correct completion, store the received data (upper data). Clear the ACK bit (bit 6 of address 001516) to "0", in which ACK is returned, and generate the STOP condition. The communication mode is set to the slave receive mode by the occurrence of STOP condition. When the MST bit (bit 7 of address 001316) is "0", return to the process , because other devices have priority to communicate.
6
1 (STOP condition) PIN (address 001316), bit 4 ? 0 (upper data transmitted) 1 (detected) AL (address 001316), bit 3 ? 0 (not detected) Receive data buffer S0 (address 001116) S2 (address 001516) 100001012 S1 (address 001316) 110100002 * Receive data read and save * Set "ACK is returned" * STOP condition occurrence * Judgment of arbitration lost detection * Judgment of bus hold
1 (bus busy) BB (address 001316), bit5 ? (Note) 0 (bus free) Re-transmission preparation End Note: Use the branch bit instruction to check bus busy. Also, execute the time out processing separately, if neccessary. * Judgment of bus busy
Fig. 2.5.27 Generating of STOP condition
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-106
APPLICATION 3804 Group (Spec.H) 2.5 Multi-master I2C-BUS interface
(3) Communication example in slave device The slave device follows the procedures to shown by Figure 2.5.28. The only difference from the master device's communication is an occurrence of interrupt request after detection of STOP condition. Reception of START condition; Transmission of ACK bit due to slave address correspondence Reception of command Reception of RESTART condition; Reception of slave address + read bit Transmission of lower data Transmission of upper data Reception of STOP condition
Figures 2.5.29 to 2.5.34 show the procedures to .

S
Slave address R/W A Command A Sr Slave address R/W A 7 bits "0" Write 8 bits 7 bits Interrupt request "1" Read
Lower data 8 bits
A
Upper data 8 bits
AP
Interrupt request
Interrupt request Master to slave Slave to master
Interrupt request
Interrupt Interrupt request request
S: START condition P: STOP condition A: ACK bit R/W: Read/Write bit Sr: RESTART condition
Fig. 2.5.28 Communication example as SMBUS slave device
Rev.1.00 Jan 14, 2004 REJ09B0212-0100Z
2-107
APPLICATION 3804 Group (Spec.H) 2.5 Multi-master I2C-BUS interface
Reception of START condition; Transmission of ACK bit due to slave address correspondence In the case of operation as the slave, all processes are performed in the interrupt after setting of the slave reception in the main process, because an interrupt request does not occur until correspondence of a slave address. In the first interrupt, after confirming correspondence of the slave address, write dummy data to receive a command into the I 2C data shift register.
1
1 (STOP condition) PIN (address 001316), bit 4 ? 0 (slave address received) 0 (not corresponded) AAS (address 001316), bit 2 ? 1 (corresponded) S0 (address 001116) 111111112 * Dummy data write to I2C data shift register * Judgment of slave address correspondence * Judgment of bus hold
End
S1 (address 001316) 000100002
* Slave receive mode set
Error processing
Fig. 2.5.29 Reception process of START condition and slave address
Rev.1.00 Jan 14, 2004 REJ09B0212-0100Z
2-108
APPLICATION 3804 Group (Spec.H) 2.5 Multi-master I2C-BUS interface
Reception of command Confirm correct completion of the command reception in the interrupt after receiving the command. After confirming correct command from the host, write dummy data to the I 2C data shift register to wait for reception of the next slave address.
2
1 (STOP condition) PIN (address 001316), bit 4 ? 0 (command received) Receive data buffer S0 (address 001116) Judgment of receive command S2 (address 001516) 100001012 S0 (address 001116) 111111112 * "ACK clock is used" select and "ACK is returned" set * Dummy data write to I2C data shift register * Receive data read and save * Judgment of bus hold
End
S1 (address 001316) 000100002
* Slave receive mode set
Error end
Fig. 2.5.30 Reception process of command
Rev.1.00 Jan 14, 2004 REJ09B0212-0100Z
2-109
APPLICATION 3804 Group (Spec.H) 2.5 Multi-master I2C-BUS interface
Reception of RESTART condition and slave address After receiving a slave address, prepare transmission data. Judgment whether receiving data or transmitting is required, because the mode is automatically switched between the receive mode and the transmit mode depending on the R/W bit of the received slave address. Accordingly, judge whether read or write referring the slave address comparison flag (AAS bit; bit 2 of address 001316).
3
1 (STOP condition) PIN (address 001316), bit 4 ? 0 (lower data received) 0 (not corresponded) AAS (address 001316), bit 2 ? 1 (corresponded) 0 (received) TRX (address 001316), bit 6 ? 1 (transmitted) S0 (address 001116) lower data
* Judgment of bus hold
* Judgment of transmit/receive mode
* Output lower data write to I2C data shift register
End
Slave receive processing, etc.
End
S1 (address 001316) 000100002
* Slave receive mode set
Error end
Fig. 2.5.31 Reception process of RESTART condition and slave address
Rev.1.00 Jan 14, 2004 REJ09B0212-0100Z
2-110
APPLICATION 3804 Group (Spec.H) 2.5 Multi-master I2C-BUS interface
Transmission of lower data Before transmitting the upper data, restart to transmit the data at and confirm correct completion of transmission of the lower data set in the slave address reception interrupt. After that, transmit the upper data.
4
1 (STOP condition) PIN (address 001316), bit 4 ? * Judgment of bus hold
0 (lower data transmission completed) 1(NACK) LRB (address 001316), bit 0 ? 0 (ACK) S0 (address 001116) Upper data * Output upper data write to I2C data shift register * ACK confirmation
End
S1 (address 001316) 000100002
* Slave receive mode set
Error end
Fig. 2.5.32 Transmission process of lower data
Rev.1.00 Jan 14, 2004 REJ09B0212-0100Z
2-111
APPLICATION 3804 Group (Spec.H) 2.5 Multi-master I2C-BUS interface
Transmission of upper data Confirm correct completion of the upper data transmission. The master returns the NACK toward the transmitted second-byte data, the upper data. Accordingly, confirm that the last receive bit (LRB bit; bit 0 of address 001316) is "1". After that, write dummy data to the I 2C data shift register and wait for the interrupt of STOP condition.
5
1 (STOP condition) PIN (address 001316), bit 4 ? * Judgment of bus hold
0 (upper data transmission completed) 0 (ACK) LRB (address 001316), bit 0 ? 1 (NACK) S0 (address 001116) 111111112 * Dummy data write to I2C data shift register * ACK confirmation
End
S1 (address 001316) 000100002
* Slave receive mode set
Error end Note: Use the branch bit instruction to check bus busy.
Fig. 2.5.33 Transmission process of upper data
Rev.1.00 Jan 14, 2004 REJ09B0212-0100Z
2-112
APPLICATION 3804 Group (Spec.H) 2.5 Multi-master I2C-BUS interface
Reception of STOP condition Confirm that the STOP condition is correctly output and the bus is released.
6
0 (address or data received) PIN (address 001316), bit 4 ? 1 (STOP condition) End processing S1 (address 001316) 000100002 * Slave receive mode set * Judgment of bus hold
End
S1(address 001316) 000100002
* Slave receive mode set
Error end
Fig. 2.5.34 Reception of STOP condition
Rev.1.00 Jan 14, 2004 REJ09B0212-0100Z
2-113
APPLICATION 3804 Group (Spec.H) 2.5 Multi-master I2C-BUS interface
2.5.7 Notes on multi-master I 2C-BUS interface (1) Read-modify-write instruction Each register of the multi-master I2C-BUS interface has bits to change by hardware. The precautions when the read-modify-write instruction such as SEB, CLB etc. is executed for each register of the multi-master I 2C-BUS interface are described below. I2C data shift register (S0: address 001116) When executing the read-modify-write instruction for this register during transfer, data may become a value not intended. I 2C slave address registers 0 to 2 (S0D0 to S0D2: addresses 0FF716 to 0FF916) When the read-modify-write instruction is executed for this register at detecting the STOP condition, data may become a value not intended. q Reason It is because hardware changes the read/write bit (RWB) at detecting the STOP condition. I2C status register (S1: address 001316) Do not execute the read-modify-write instruction for this register because all bits of this register are changed by hardware. I2C control register (S1D: address 001416) When the read-modify-write instruction is executed for this register at detecting the START condition or at completing the byte transfer, data may become a value not intended. q Reason Because hardware changes the bit counter (BC0 to BC2). I2C clock control register (S2: address 001516) The read-modify-write instruction can be executed for this register. I2C START/STOP condition control register (S2D: address 001616) The read-modify-write instruction can be executed for this register.
Rev.1.00 Jan 14, 2004 REJ09B0212-0100Z
2-114
APPLICATION 3804 Group (Spec.H) 2.5 Multi-master I2C-BUS interface
(2) START condition generating procedure using multi-master Procedure example (The necessary conditions of the generating procedure are described as the following to ). LDA #SLADR (Taking out of slave address value) SEI (Interrupt disabled) BBS 5, S1, BUSBUSY (BB flag confirming and branch process) BUSFREE: STA S0 (Writing of slave address value) LDM #$F0, S1 (Trigger of START condition generating) CLI (Interrupt enabled) : : BUSBUSY: CLI (Interrupt enabled) : : Use "Branch on Bit Set" of "BBS 5, S1, -" for the BB flag confirming and branch process. Use "STA, STX" or "STY" of the zero page addressing instruction for writing the slave address value to the I 2C data shift register (S0: address 001116). Execute the branch instruction of above and the store instruction of above continuously shown by the above procedure example. Disable interrupts during the following three process steps: * BB flag confirming * Writing of slave address value * Trigger of START condition generating (3) RESTART condition generating procedure in master Procedure example (The necessary conditions of the generating procedure are described as the following to ). Execute the following procedure when the PIN bit is "0". LDM #$00, S1 (Select slave receive mode) LDA #SLADR (Taking out of slave address value) SEI (Interrupt disabled) STA S0 (Writing of slave address value) LDM #$F0, S1 (Trigger of RESTART condition generating) CLI (Interrupt enabled) : : Select the slave receive mode when the PIN bit is "0". Do not write "1" to the PIN bit. The TRX bit becomes "0" and the SDA pin is released. The SCL pin is released by writing the slave address value to the I 2C data shift register. Disable interrupts during the following two process steps: * Writing of slave address value * Trigger of RESTART condition generating (4) Writing to I 2C status register (S1: address 001316) Do not execute an instruction to set the PIN bit to "1" from "0" and an instruction to set the MST and TRX bits to "0" from "1" simultaneously. It is because it may enter the state that the SCL pin is released and the SDA pin is released after about one machine cycle. Do not execute an instruction to set the MST and TRX bits to "0" from "1" simultaneously when the PIN bit is "1". It is because it may become the same as above.
Rev.1.00 Jan 14, 2004 REJ09B0212-0100Z
2-115
APPLICATION 3804 Group (Spec.H) 2.5 Multi-master I2C-BUS interface
(5) Writing to I 2C clock control register (S2: address 001516) Do not write data into the I2C clock control register during transfer. If data is written during transfer, the I 2C clock generator is reset, so that data cannot be transferred normally. (6) Switching of SCL/SDA interrupt pin polarity selection bit, SCL/SDA interrupt pin selection bit, I 2C-BUS interface enable bit When changing the setting of the SCL/SDA interrupt pin polarity selection bit, the SCL/SDA interrupt pin selection bit, or the I 2C-BUS interface enable bit ES0, the SCL/SDA interrupt request bit may be set. When selecting the SCL/SDA interrupt source, disable the interrupt before the SCL/SDA interrupt pin polarity selection bit, the SCL/SDA interrupt pin selection bit, or the I2C-BUS interface enable bit ES0 is set. Reset the request bit to "0" after setting these bits, and enable the interrupt. (7) Process of after STOP condition generating in master mode Do not write data in the I2C data shift register (S0) and the I2C status register (S1) until the bus busy flag BB becomes "0" after generating the STOP condition in the master mode. It is because the STOP condition waveform might not be normally generated. Reading to the above registers does not have the problem. (8) ES0 bit switch In standard clock mode when SSC = "000102" or in high-speed clock mode, flag BB may switch to "1" if ES0 bit is set to "1" when SDA is "L". Countermeasure: Set ES0 to "1" when SDA is "H".
Rev.1.00 Jan 14, 2004 REJ09B0212-0100Z
2-116
APPLICATION 3804 Group (Spec.H) 2.5 Multi-master I2C-BUS interface
2.5.8 Notes on programming for SMBUS interface (1) Time out process For a smart battery system, the time out process with a program is required so that the communication can be completed even when communication is interrupted. It is because there is possibility of extracting a battery from a PC. The specifications are defined so that communication has been able to be completed within 25 ms from START condition to STOP condition and within 10 ms from the ACK pulse to the ACK pulse of each byte. Accordingly, the following two should be considered as count start conditions. SDA falling edge caused by SCL/SDA interrupt This is the countermeasure for a communication interrupt in the middle of from START condition to a slave address. However, the detection condition must be considered because a interrupt is also generated by communication from other masters to other slaves. SMBUS interrupt after receiving slave address This is the countermeasure for when communication is interrupted from receiving a slave address until receiving a command. (2) Low hold of communication line The I2C-BUS interface conforms to the I2C-BUS Standard Specifications. However, because the use condition of SMBUS differs from the I 2C-BUS's, there is possibility of occurrence of the following problem. Low hold of SDA line caused by ACK pulse at voltage drop of communication line When the SMBUS voltage slowly drops, that is caused by extracting a battery from equipment or turning off a PC's power or etc., it might be incorrectly treated as the SCL pulse near the threshold level voltage. When the SDA is judged "L" in that condition, it becomes the general call and the ACK is transmitted. However, when the SCL remains "L" at the ACK pulse, the SDA continuously remains "L" until input of the next SCL pulse. Countermeasure: As explained before, start the time out count at the falling of SDA line of START condition and reset ES0 bit of the S1D register when the time out is satisfied (Note). Note: Do not use the read-modify-write instruction at this time. Furthermore, when the ES0 bit is set to "0", it becomes a general-purpose port ; so that the port must be set to input mode or "H".
Rev.1.00 Jan 14, 2004 REJ09B0212-0100Z
2-117
APPLICATION 3804 Group (Spec.H) 2.6 PWM
2.6 PWM
This paragraph explains the registers setting method and the notes relevant to the PWM. 2.6.1 Memory map
Address 002B16 002C16 002D16 PWM control register (PWMCON) PWM prescaler (PREPWM) PWM register (PWM)
Fig. 2.6.1 Memory map of registers relevant to PWM 2.6.2 Relevant registers
PWM control register
b7 b6 b5 b4 b3 b2 b1 b0 PWM control register (PWMCON: address 002B16)
b
Name
Functions
At reset R W
0 0 0 0 0 0 0 0
0 PWM function 0 : PWM disabled enable bit 1 : PWM enabled 1 Count source 0 : f(XIN) selection bit 1 : f(XIN)/2 2 Nothing is arranged for these bits. These are 3 write disabled bits. When these bits are read 4 out, the contents are "0". 5 6 7

Fig. 2.6.2 Structure of PWM control register
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-118
APPLICATION 3804 Group (Spec.H) 2.6 PWM
PWM prescaler
b7 b6 b5 b4 b3 b2 b1 b0 PWM prescaler (PREPWM: address 002C16)
b
Functions
At reset R W
Undefined Undefined Undefined Undefined Undefined Undefined Undefined Undefined
0 *Set the PWM period. 1 *The value set in this register is written to both PWM prescaler pre-latch and PWM prescaler 2 latch at the same time. 3 * When data is written to this register during PWM output, the pulse corresponding to 4 changed value is output at the next period. 5 * When this register is read out, the count value of the PWM prescaler latch is read out. 6 7
Fig. 2.6.3 Structure of PWM prescaler
PWM register
b7 b6 b5 b4 b3 b2 b1 b0 PWM register (PWM: address 002D16)
b
Functions
At reset R W
Undefined Undefined Undefined Undefined Undefined Undefined Undefined Undefined
0 * Set the PWM "H" level output interval. 1 * The value set in this register is written to both PWM register pre-latch and PWM register 2 latch at the same time. 3 * When data is written to this register during PWM output, the pulse corresponding to 4 changed value is output at the next period. 5 * When this register is read out, the contents of the PWM register latch is read out. 6 7
Fig. 2.6.4 Structure of PWM register
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-119
APPLICATION 3804 Group (Spec.H) 2.6 PWM
2.6.3 PWM output circuit application example Outline : The rotation speed of the motor is controlled by using PWM (pulse width modulation) output. Figure 2.6.5 shows a connection diagram ; Figures 2.6.6 shows PWM output timing, and Figure 2.6.7 shows a setting of the related registers.
P56/PWM D/A converter
M Motor driver
3804 group (Spec. H)
Fig. 2.6.5 Connection diagram Specifications : * Motor is controlled by using the PWM output function of 8-bit resolution. * Clock f(XIN) = 5 MHz * "T", PWM cycle : 102 s * "t", "H" level width of output pulse : 40 s (Fixed speed) A motor speed can be changed by modifying the "H" level width of output pulse.
t = 40 s
PWM output T = 102 s
Fig. 2.6.6 PWM output timing
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-120
APPLICATION 3804 Group (Spec.H) 2.6 PWM
PWM control register (Address : 002B16)
b7 b0
PWMCON
01
PWM output: Enabled (Note) Count source: f(XIN)
PWM prescaler (Address : 002C16)
b7 b0
PREPWM
n
Set "T", PWM cycle n=1
[Equation] 255 (n + 1) T= f(XIN)
PWM register (Address : 002D16)
b7 b0
PWM
m
Set "t", "H" level width of PWM m = 100
[Equation] t= Tm 255
Note: The PWM output function has priority even when bit 6 (corresponding bit to P56 pin) of Port P5 direction register is set to "0" (input mode).
Fig. 2.6.7 Setting of relevant registers 1. Set the PWM function enable bit to "1" : The P56/PWM pin is used as the PWM pin. The pulse beginning with "H" level pulse is output. 2. Set the PWM function enable bit to "0" : The P56/PWM pin is used as the port P56. Thus, when fixing the output level, take the following procedure: (1) Write an output value to bit 6 of the port P5 register. (2) Write "010000002" to the port P5 direction register. 3. After data is set to the PWM prescaler and the PWM register, the PWM waveforms corresponding to updated data will be output from the next repetitive cycle.
PWM output
Change PWM output data
From the next repetitive cycle, output modified data
Fig. 2.6.8 PWM output
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-121
APPLICATION 3804 Group (Spec.H) 2.6 PWM
By setting the related registers as shown by Figure 2.6.7, PWM waveforms are output to the externals. This PWM output is integrated through the low pass filter, and that converted into DC signals is used for control of the motor. Figure 2.6.9 shows control procedure.
~ ~
P5 (Address : 000A16), bit6 P5D (Address : 000B16) PREPWM (Address : 002C16) PWM (Address : 002D16) PWMCON (Address : 002B16) 0 X1XXXXXX2 1 100 XXXXXX012
* X : This bit is not used here. Set it to "0" or "1" arbitrarily. * "L" level output from P56/PWM pin
* PWM period setting * "H" level width of PWM setting * PWM count source selected, PWM output enabled
~ ~
Fig. 2.6.9 Control procedure 2.6.4 Notes on PWM The PWM starts after the PWM enable bit is set to enable and "L" level is output from the PWM pin. The length of this "L" level output is as follows: n+1 2 * f(XIN) n+1 f(XIN)
(s)
(Count source selection bit = 0, where n is the value set in the prescaler)
(s)
(Count source selection bit = 1, where n is the value set in the prescaler)
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-122
APPLICATION 3804 Group (Spec.H) 2.7 A/D converter
2.7 A/D converter
This paragraph explains the registers setting method and the notes relevant to the A/D converter. 2.7.1 Memory map
Address 003416 003516 AD/DA control register (ADCON) AD conversion register 1 (AD1)
003816 003916
AD conversion register 2 (AD2)
Interrupt source selection register (INTSEL)
003D16
Interrupt request register 2 (IREQ2)
003F16
Interrupt control register 2 (ICON2)
Fig. 2.7.1 Memory map of registers relevant to A/D converter 2.7.2 Relevant registers
AD/DA control register
b7 b6 b5 b4 b3 b2 b1 b0 AD/DA control register (ADCON: address 003416)
b
Name
b2 b1 b0
Functions
0 0 0: P60/AN0 or P00/AN8 0 0 1: P61/AN1 or P01/AN9 0 1 0: P62/AN2 or P02/AN10 0 1 1: P63/AN3 or P03/AN11 1 0 0: P64/AN4 or P04/AN12 1 0 1: P65/AN5 or P05/AN13 1 1 0: P66/AN6 or P06/AN14 1 1 1: P67/AN7 or P07/AN15
At reset R W
0
0 Analog input pin selection bits 1 1
0
2
0
0: Conversion in progress 3 AD conversion 1: Conversion completed completion bit 4 Analog input pin 0: AN0 to AN7 side 1: AN8 to AN15 side selection bit 2 5 Nothing is arranged for this bit. This is a write disabled bit. When this bit is read out, the contents are "0". 6 DA1 output enable 0: DA1 output disabled 1: DA1 output enabled bit 7 DA2 output enable 0: DA2 output disabled 1: DA2 output enabled bit
1 0 0
0 0
Fig. 2.7.2 Structure of AD/DA control register
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-123
APPLICATION 3804 Group (Spec.H) 2.7 A/D converter
AD conversion register 1
b7 b6 b5 b4 b3 b2 b1 b0 AD conversion register 1 (AD1: address 003516)
b
Functions
At reset R W
Undefined Undefined 0 Undefined 0 Undefined 0 Undefined 0 Undefined 0 Undefined 0 Undefined 0
0 This is A/D conversion result stored bits. This is 1 read exclusive register. 2 8-bit read b7 b0 3 b9 b8 b7 b6 b5 b4 b3 b2 4 5 10-bit read b7 b0 6 b7 b6 b5 b4 b3 b2 b1 b0 7
Fig. 2.7.3 Structure of AD conversion register 1
AD conversion register 2
b7 b6 b5 b4 b3 b2 b1 b0 AD conversion register 2 (AD2: address 003816)
b
Functions
At reset R W
0 This is A/D conversion result stored bits. This is Undefined read exclusive register. 10-bit read b0 b7 Undefined 1 0 b9 b8 2 3 4 5 6 7 Nothing is arranged for these bits. These are write disabled bits. When these bits are read out, the contents are "0". 0 0 0 0 0 0
Conversion mode selection bit
0: 10-bit A/D mode 1: 8-bit A/D mode
Fig. 2.7.4 Structure of AD conversion register 2
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-124
APPLICATION 3804 Group (Spec.H) 2.7 A/D converter
Interrupt source selection register
b7 b6 b5 b4 b3 b2 b1 b0 Interrupt source selection register (INTSEL: address 003916)
b
Name
Functions
0: INT0 interrupt 1: Timer Z interrupt 0: Serial I/O2 interrupt 1: Timer Z interrupt 0: Serial I/O1 transmit interrupt 1: SCL, SDA interrupt 0: CNTR0 interrupt 1: SCL, SDA interrupt 0: INT4 interrupt 1: CNTR2 interrupt 0: INT2 interrupt 1: I2C interrupt 0: CNTR1 interrupt 1: Serial I/O3 receive interrupt 0: A/D converter interrupt 1: Serial I/O3 transmit interrupt
At reset R W
0
0 INT0/Timer Z interrupt source selection bit (*1) 1 Serial I/O2/Timer Z interrupt source selection bit (*1) 2 Serial I/O1 transmit/ SCL, SDA interrupt source selection bit (*2) 3 CNTR0/SCL, SDA interrupt source selection bit (*2) 4 INT4/CNTR2 interrupt source selection bit 5 INT2/I2C interrupt source selection bit 6 CNTR1/Serial I/O3 receive interrupt source selection bit 7 AD converter/Serial I/O3 transmit interrupt source selection bit
0
0
0
0
0 0
0
*1: Do not write 1 to these bits simultaneously. *2: Do not write 1 to these bits simultaneously.
Fig. 2.7.5 Structure of Interrupt source selection register
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-125
APPLICATION 3804 Group (Spec.H) 2.7 A/D converter
Interrupt request register 2
b7 b6 b5 b4 b3 b2 b1 b0 Interrupt request register 2 (IREQ2 : address 003D16)
b
Name
Functions
0 : No interrupt request issued 1 : Interrupt request issued 0 : No interrupt request issued 1 : Interrupt request issued 0 : No interrupt request issued 1 : Interrupt request issued 0 : No interrupt request issued 1 : Interrupt request issued 0 : No interrupt request issued 1 : Interrupt request issued 0 : No interrupt request issued 1 : Interrupt request issued 0 : No interrupt request issued 1 : Interrupt request issued
At reset R W
0 0
0 CNTR0/SCL, SDA interrupt request bit 1 CNTR1/Serial I/O3 receive interrupt request bit 2 Serial I/O2/Timer Z interrupt request bit 3 INT2/I2C interrupt request bit 4 INT3 interrupt request bit 5 INT4/CNTR2 interrupt request bit 6 AD converter/Serial I/O3 transmit interrupt request bit
0 0 0 0 0

7 Nothing is arranged for this bit. This is a write disabled bit. When this bit is read out, the contents are 0 . : 0 can be set by software, but 1 cannot be set.
0
Fig. 2.7.6 Structure of Interrupt request register 2
Interrupt control register 2
b7 b6 b5 b4 b3 b2 b1 b0
0
Interrupt control register 2 (ICON2 : address 003F16)
b
Name
Functions
0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled
At reset R W
0 0
0 CNTR0/SCL, SDA interrupt enable bit CNTR1/ Serial I/O3 1 receive interrupt enable bit 2 Serial I/O2/ Timer Z interrupt enable bit 3 INT2/I2C interrupt enable bit 4 INT3 interrupt enable bit 5 INT4/CNTR2 interrupt enable bit 6 AD converter/Serial I/O3 transmit interrupt enable bit 7 Fix this bit to "0".
0 0 0 0 0
0
Fig. 2.7.7 Structure of Interrupt control register 2
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-126
APPLICATION 3804 Group (Spec.H) 2.7 A/D converter
2.7.3 A/D converter application examples (1) Conversion of analog input voltage 1 Outline : The analog input voltage input from a sensor is converted to digital values. Figure 2.7.8 shows a connection diagram, and Figure 2.7.9 shows the relevant registers setting.
P60/AN0
Sensor
3804 Group (Spec. H)
Fig. 2.7.8 Connection diagram Specifications : *The analog input voltage input from a sensor is converted to digital values. *P60/AN0 pin is used as an analog input pin. *10-bit A/D mode
AD/DA control register (address 003416)
b7 b0
ADCON
0 00 00
Analog input pin : P60/AN0 selected A/D conversion start Analog input pin : AN0-AN7 selected
AD conversion register 2 (address 003816)
b7 b0
AD2
0 A result of A/D conversion is stored (read-only) (Note). 10-bit A/D mode
AD conversion register 1 (address 003516)
b7 b0
AD1
(Read-only)
A result of A/D conversion is stored (Note). Note: After bit 3 of AD/DA control register (ADCON) is set to "1", read out that contents. When reading 10-bit data, read address 003816 before address 003516. When reading 10-bit data, bits 2 to 6 of address 003816 become "0".
Fig. 2.7.9 Relevant registers setting
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-127
APPLICATION 3804 Group (Spec.H) 2.7 A/D converter
An analog input signal from a sensor is converted to the digital value according to the relevant registers setting shown by Figure 2.7.9. Figure 2.7.10 shows the control procedure for 10-bit A/D mode.
q X: This bit is not used here. Set it to "0" or "1" arbitrarily. AD2 (address 003816) 0XXXXXXX2 *10-bit A/D mode selected
ADCON (address 003416)
XX0000002
*P60/AN0 pin selected as analog input pin *A/D conversion start
ADCON (address 003416), bit3 ?
0
*Judgment of A/D conversion completion
1 Read out AD2 (address 003816) *Read out of high-order digit (b9, b8) of conversion result
Read out AD1 (address 003516)
*Read out of low-order digit (b7 - b0) of conversion result
Fig. 2.7.10 Control procedure (10-bit A/D mode)
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-128
APPLICATION 3804 Group (Spec.H) 2.7 A/D converter
(2) Conversion of analog input voltage 2 Outline : The analog input voltage input from a sensor is converted to digital values. Figure 2.7.11 shows a connection diagram, and Figure 2.7.12 shows the relevant registers setting.
P60/AN0
Sensor
3804 Group (Spec. H)
Fig. 2.7.11 Connection diagram Specifications : *The analog input voltage input from a sensor is converted to digital values. *P60/AN0 pin is used as an analog input pin. *8-bit A/D mode
AD/DA control register (address 003416)
b7 b0
ADCON
0 00 00
Analog input pin : P60/AN0 selected A/D conversion start Analog input pin : AN0-AN7 selected
AD conversion register 2 (address 003816)
b7 b0
AD2
1 8-bit A/D mode
AD conversion register 1 (address 003516)
b7 b0
AD1
(Read-only)
A result of A/D conversion is stored (Note). Note: After bit 3 of AD/DA control register (ADCON) is set to "1", read out that contents. When reading 8-bit data, read address 003516 only.
Fig. 2.7.12 Relevant registers setting
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-129
APPLICATION 3804 Group (Spec.H) 2.7 A/D converter
An analog input signal from a sensor is converted to the digital value according to the relevant registers setting shown by Figure 2.7.12. Figure 2.7.13 shows the control procedure for 8-bit A/D mode.
q x: This bit is not used here. Set it to "0" or "1" arbitrarily. AD2 (address 003816) 1XXXXXXX2 *8-bit A/D mode selected
ADCON (address 003416)
XX0000002
*P60/AN0 pin selected as analog input pin *A/D conversion start
ADCON (address 003416), bit3 ?
0
*Judgment of A/D conversion completion
1 Read out AD1 (address 003516) *Read out of conversion result
Fig. 2.7.13 Control procedure (8-bit A/D mode)
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-130
APPLICATION 3804 Group (Spec.H) 2.7 A/D converter
2.7.4 Notes on A/D converter (1) Analog input pin Make the signal source impedance for analog input low, or equip an analog input pin with an external capacitor of 0.01 F to 1 F. Further, be sure to verify the operation of application products on the user side. q Reason An analog input pin includes the capacitor for analog voltage comparison. Accordingly, when signals from signal source with high impedance are input to an analog input pin, charge and discharge noise generates. This may cause the A/D conversion precision to be worse. (2) A/D converter power source pin The AVSS pin is A/D converter power source pins. Regardless of using the A/D conversion function or not, connect it as following : * AVSS : Connect to the VSS line q Reason If the AVSS pin is opened, the microcomputer may have a failure because of noise or others. (3) Clock frequency during A/D conversion The comparator consists of a capacity coupling, and a charge of the capacity will be lost if the clock frequency is too low. Thus, make sure the following during an A/D conversion. * f(XIN) is 500 kHz or more * Do not execute the STP instruction
(4) Difference between at 8-bit reading in 10-bit A/D mode and at 8-bit A/D mode At 8-bit reading in the 10-bit A/D mode, "-1/2 LSB" correction is not performed to the A/D conversion result. In the 8-bit A/D mode, the A/D conversion characteristics is the same as 3802 group's characteristics because "-1/2 LSB" correction is performed.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-131
APPLICATION 3804 Group (Spec.H) 2.8 D/A converter
2.8 D/A Converter
This paragraph explains the registers setting method and the notes relevant to the D/A converter. 2.8.1 Memory map
000716
Port P3 direction register (P3D)
003416 003616 003716
AD/DA control register (ADCON) DA1 conversion register (DA1) DA2 conversion register (DA2)
Fig. 2.8.1 Memory map of registers relevant to D/A converter
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-132
APPLICATION 3804 Group (Spec.H) 2.8 D/A converter
2.8.2 Relevant registers
Port P3 direction register
b7 b6 b5 b4 b3 b2 b1 b0 Port P3 direction register (P3D: address 000716)
b
Name
Functions
0 : Port P30 input mode 1 : Port P30 output mode 0 : Port P31 input mode 1 : Port P31 output mode 0 : Port P32 input mode 1 : Port P32 output mode 0 : Port P33 input mode 1 : Port P33 output mode 0 : Port P34 input mode 1 : Port P34 output mode 0 : Port P35 input mode 1 : Port P35 output mode 0 : Port P36 input mode 1 : Port P36 output mode 0 : Port P37 input mode 1 : Port P37 output mode
At reset R W
0 0 0 0 0 0 0 0
0 Port P3 direction register 1 2 3 4 5 6 7
Fig. 2.8.2 Structure of Port P5 direction register
AD/DA control register
b7 b6 b5 b4 b3 b2 b1 b0 AD/DA control register (ADCON: address 003416)
b
Name
b2 b1 b0
Functions
0 0 0: P60/AN0 or P00/AN8 0 0 1: P61/AN1 or P01/AN9 0 1 0: P62/AN2 or P02/AN10 0 1 1: P63/AN3 or P03/AN11 1 0 0: P64/AN4 or P04/AN12 1 0 1: P65/AN5 or P05/AN13 1 1 0: P66/AN6 or P06/AN14 1 1 1: P67/AN7 or P07/AN15
At reset R W
0
0 Analog input pin selection bits 1 1
0
2
0
0: Conversion in progress 3 AD conversion 1: Conversion completed completion bit 4 Analog input pin 0: AN0 to AN7 side 1: AN8 to AN15 side selection bit 2 5 Nothing is arranged for this bit. This is a write disabled bit. When this bit is read out, the contents are "0". 6 DA1 output enable 0: DA1 output disabled 1: DA1 output enabled bit 7 DA2 output enable 0: DA2 output disabled 1: DA2 output enabled bit
1 0 0
0 0
Fig. 2.8.3 Structure of AD/DA control register
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-133
APPLICATION 3804 Group (Spec.H) 2.8 D/A converter
DAi conversion register
b7 b6 b5 b4 b3 b2 b1 b0 DAi conversion register (i = 1, 2) (DAi: addresses 003616, 003716)
b
Functions
At reset R W
0 0 0 0 0 0 0 0
0 This is D/A output value stored bits. This is write 1 exclusive register. 2 3 4 5 6 7
Fig. 2.8.4 Structure of DAi converter register
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-134
APPLICATION 3804 Group (Spec.H) 2.8 D/A converter
2.8.3 D/A converter application example (1) Speaker output volume modulation Outline: The volume of a speaker output is modulated by using D/A converter. Specifications: *Timer X modulates the period of sound for the pitch interval, so that a fixed pitch ("la": approx. 440 Hz) can be output. Modulating the amplitude with the D/A output value controls the volume. *Use f(XIN) = 6 MHz. *Use DA1 (P30/DA1 pin) as D/A converter. Figure 2.8.5 shows a peripheral circuit example and Figure 2.8.6 shows a speaker output example. Figure 2.8.7 shows the relevant registers setting.
3804 Group (Spec. H)
P30/DA1
Amplification circuit Power amplifier
+
Fig. 2.8.5 Peripheral circuit example
Modulation of volume VREF (amplitude is set by D/A1 output)
VSS
Timer X interrupt
Timer X interrupt
Timer X interrupt
Timer X interrupt
Timer X interrupt
Timer X interrupt
Modulation of pitch interval: 440 Hz (Cycle is set by timer X)
Fig. 2.8.6 Speaker output example
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-135
APPLICATION 3804 Group (Spec.H) 2.8 D/A converter
b7
b0
0
Port P3 direction register (P3D) (address 000716)
P30/DA1: Input mode
b7
b0
1
AD/DA control register (ADCON) (address 003416)
DA1 output enabled
b7
b0
001
Timer XY mode register (TM) (address 002316)
Timer X count: Stop Timer mode
b7
b0
0011
Timer 12, X count source serection register (T12XCSS) (address 000E16)
Timer X count source: f(XIN)/16
b7
b0
2-1
Prescaler X (PREX) (address 002416)
Set "division ratio -1"
b7
b0
D616 - 1
Timer X (TX) (address 002516)
Set "division ratio -1"
b7
b0
0
Interrupt request register 1 (IREQ1) (address 003C16)
Timer X interrupt request
b7
b0
1
Interrupt control register 1 (ICON1) (address 003E16)
Timer X interrupt: Enabled
b7
b0
DA1 conversion register (DA1) (address 003616)
Set conversion value (n) Analog voltage V =
b7 b0
VREF x n 256
(n=0 to 255)
000
Timer XY mode register (TM) (address 002316 )
Timer X count: Start
Fig. 2.8.7 Relevant registers setting
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-136
APPLICATION 3804 Group (Spec.H) 2.8 D/A converter
When the registers are set as shown in Figure 2.8.7, the speaker output volume is modulated by the D/A output value. Figure 2.8.8 shows the control procedure.
RESET
q x: This bit is not used here. Set it to "0" or "1" arbitrarily.
Initialization SEI CLT (Note 1) CLD (Note 2) (address 003E16), bit4 0 ICON1 (address 000716), bit0 0 P3D X1XXXXXX2 (address 003416) ADCON XX001XXX2 (address 002316) TM 0011XXXX2 T12XCSS (address 000E16) 2-1 (address 002416) PREX D616 - 1 (address 002516) TX 1 WORK flag (Note 3) (address 003C16), bit4 0 IREQ1 (address 003E16), bit4 1 ICON1 (address 003616) Set output value (volume) DA1 CLI (address 002316) XX000XXX2 TM *All interrupts disabled
Fig. 2.8.8 Control procedure
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
..... .....
*Timer X interrupt disabled *Set port P30 to input mode *DA1 output enabled *Timer Y: Timer mode, Timer X count: Stop *Timer X count source: f(XIN)/16 *Set "division ratio - 1" to Prescaler X *Set "division ratio - 1" to Timer X *Timer X interrupt request bit cleared *Timer X interrupt: Enabled *D/A converter start *All interrupts enabled *Timer X count start
Main processing
Notes 1: When using Index X mode flag 2: When using Decimal mode flag 3: The WORK flag is a user flag for work. When this flag is "1 ", a value other than Vss is output from the DA output pin. When this flag is "0", Vss is output from the DA output pin.
Timer X interrupt process routine
Push registers to stack
*Push registers used in interrupt process routine
Value of WORK flag ? "1" Set value except Vss to DA1 conversion register. Set "0" to WORK flag.
"0"
Set value of Vss to DA1 conversion register.
Set "1" to WORK flag.
Pop registers
*Pop registers pushed to stack
RTI
Decide an D/A value from several times of D/A conversion results.
2-137
APPLICATION 3804 Group (Spec.H) 2.8 D/A converter
2.8.4 Notes on D/A converter (1) Vcc when using D/A converter The D/A converter accuracy when Vcc is 4.0 V or less differs from that of when Vcc is 4.0 V or more. When using the D/A converter, we recommend using a Vcc of 4.0 V or more. (2) DAi conversion register when not using D/A converter When a D/A converter is not used, set all values of the DAi conversion registers (i = 1, 2) to "0016". The initial value after reset is "0016".
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-138
APPLICATION 3804 Group (Spec.H) 2.9 Watchdog timer
2.9 Watchdog timer
This paragraph explains the registers setting method and the notes relevant to the watchdog timer. 2.9.1 Memory map
Address 001E16 003B16
Watchdog timer control register (WDTCON)
CPU mode register (CPUM)
Fig. 2.9.1 Memory map of registers relevant to watchdog timer 2.9.2 Relevant registers
Watchdog timer control register
b7 b6 b5 b4 b3 b2 b1 b0 Watchdog timer control register (WDTCON: address 001E16)
b
Name
Functions
0 Watchdog timer H 1 (for read-out of high-order 6 bit) 2 3 4 5 6 STP instruction 0: STP instruction enabled 1: STP instruction disabled disable bit 7 Watchdog timer H 0: Watchdog timer L underflow count source selection 1: f(XIN)/16 or f(XCIN)/16 bit
At reset R W 1 1 1 1 1 1
0 0
Fig. 2.9.2 Structure of Watchdog timer control register
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-139
APPLICATION 3804 Group (Spec.H) 2.9 Watchdog timer
CPU mode register
b7 b6 b5 b4 b3 b2 b1 b0
1
CPU mode register (CPUM: address 003B16)
b
Name
b1 b0
Functions
00 : Single-chip mode 01 : 10 : Not available 11 : 0 : 0 page 1 : 1 page 0: I/O port function (stop oscillating) 1: XCIN-XCOUT oscillation function 0: Oscillating 1: Stopped 0 0: =f(XIN)/2 (high-speed mode) 0 1: =f(XIN)/8 (middle-speed mode) 1 0: =f(XCIN)/2 (low-speed mode) 1 1: Not available
b7 b6
At reset R W
0 0 0 1 0
0 Processor mode bits 1 2 Stack page selection bit 3 Fix this bit to "1". 4 Port Xc switch bit
5 Main clock (XINXOUT) stop bit 6 Main clock division ratio selection bits
0 1
7
0
Fig. 2.9.3 Structure of CPU mode register
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-140
APPLICATION 3804 Group (Spec.H) 2.9 Watchdog timer
2.9.3 Watchdog timer application examples (1) Detection of program runaway Outline: If program runaway occurs, let the microcomputer reset, using the internal timer for detection of program runaway. Specifications: *High-speed mode is used as a main clock division ratio. *An underflow signal of the watchdog timer L is supplied as the count source of watchdog timer H. *1 cycle of main routine is 65.536 ms or less. *Before the watchdog timer H underflows, "0" is set into bit 7 of the watchdog timer control register at every cycle in a main routine. *An underflow of watchdog timer H is judged to be program runaway, and the microcomputer is returned to the reset status. Figure 2.9.4 shows a watchdog timer connection and division ratio setting; Figure 2.9.5 shows the relevant registers setting; Figure 2.9.6 shows the control procedure.
Fixed f(XIN) = 16 MHz 1/16
Watchdog timer L Watchdog timer H 1/256 1/256 Reset circuit Internal reset
RESET STP instruction disable bit STP instruction
Fig. 2.9.4 Watchdog timer connection and division ratio setting
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-141
APPLICATION 3804 Group (Spec.H) 2.9 Watchdog timer
CPU mode register (address 003B16)
b7 b0
CPUM
000
1
00 Processor mode: Single-chip mode Fix to "1" Main clock (XIN-XOUT): Operating Main clock division ratio: f(XIN)/2 (high-speed mode)
Watchdog timer control register (address 001E16)
b7 b0
WDTCON
00 Watchdog timer H (for read-out of high-order 6 bits) Enable STP instruction Watchdog timer H count source: Watchdog timer L underflow
Fig. 2.9.5 Relevant registers setting
RESET
Initialization SEI CLT CLD CPUM (address 003B16) : : CLI
*All interrupts disabled *Processor mode: Single-chip mode *Main clock f(XIN): Operating *High-speed mode selected as main clock division ratio *Interrupts enabled
000X1X002
WDTCON (address 001E16)
000XXXXX2
*Watchdog timer L underflow selected as Watchdog timer H count source *STP instruction enabled
Main processing : :
Fig. 2.9.6 Control procedure 2.9.4 Notes on watchdog timer qMake sure that the watchdog timer H does not underflow while waiting Stop release, because the watchdog timer keeps counting during that term. qWhen the STP instruction disable bit has been set to "1", it is impossible to switch it to "0" by a program.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-142
APPLICATION 3804 Group (Spec.H) 2.10 Reset
2.10 Reset
2.10.1 Connection example of reset IC
1
VCC
Power source
5 4 GND 3 0.1 F VSS
M62022L
Output
RESET
Delay capacity
3804 Group (Spec. H)
Fig. 2.10.1 Example of poweron reset circuit Figure 2.10.2 shows the system example which switches to the RAM backup mode by detecting a drop of the system power source voltage with the INT interrupt.
System power source voltage +5 V
+
7 VCC1 RESET 5
VCC
RESET
2
VCC2
INT
3
INT VSS
1
V1
GND 4
Cd
6
3804 Group (Spec. H)
M62009L,M62009P,M62009FP
Fig. 2.10.2 RAM backup system
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-143
APPLICATION 3804 Group (Spec.H) 2.10 Reset
2.10.2 Notes on RESET pin Connecting capacitor In case where the RESET signal rise time is long, connect a ceramic capacitor or others across the RESET pin and the VSS pin. Use a 1000 pF or more capacitor for high frequency use. When connecting the capacitor, note the following : * Make the length of the wiring which is connected to a capacitor as short as possible. * Be sure to verify the operation of application products on the user side. q Reason If the several nanosecond or several ten nanosecond impulse noise enters the RESET pin, it may cause a microcomputer failure.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-144
APPLICATION 3804 Group (Spec.H) 2.11 Clock generating circuit
2.11 Clock generating circuit
This paragraph explains how to set the registers relevant to the clock generating circuit and describes an application example. 2.11.1 Relevant registers
CPU mode register
b7 b6 b5 b4 b3 b2 b1 b0
1
CPU mode register (CPUM: address 003B16)
b
Name
b1 b0
Functions
00 : Single-chip mode 01 : Not available 10 : Not available 11 : Not available 0 : 0 page 1 : 1 page 0: I/O port function (oscillation stopped) 1: XCIN-XCOUT oscillation function 0: Oscillating 1: Stopped 0 0: =f(XIN)/2 (high-speed mode) 0 1: =f(XIN)/8 (middle-speed mode) 1 0: =f(XCIN)/2 (low-speed mode) 1 1: Not available
b7 b6
At reset R W
0 0 0 1 0
0 Processor mode bits 1 2 Stack page selection bit 3 Fix this bit to "1". 4 Port Xc switch bit
5 Main clock (XINXOUT) stop bit Main clock division 6 ratio selection bits
0 1
7
0
Fig. 2.11.1 Structure of CPU mode register
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-145
APPLICATION 3804 Group (Spec.H) 2.11 Clock generating circuit
2.11.2 Clock generating circuit application example (1) Status transition during power failure Outline: The clock counts up every second by using the timer interrupt during a power failure.
Input port (Note)
Power failure detection signal
3804 Group (Spec. H) Note: A signal is detected when input to input port, interrupt input pin, or analog input pin.
Fig. 2.11.2 Connection diagram Specifications: *Reducing power dissipation as low as possible while maintaining clock function *Clock: f(XIN) = 8 MHz, f(XCIN) = 32.768 kHz *Port processing Input port: Fixed to "H" or "L" level externally. Output port: Fixed to output level that does not cause current flow to the external. (Example) Fix to "H" for an LED circuit that turns on at "L" output level. I/O port: Input port Fixed to "H" or "L" level externally. Output port Output of data that does not consume current VREF pin: Terminate A/D conversion operation Stop VREF current dissipation by setting value of DAi conversion register to "0016". Figure 2.11.3 shows the status transition diagram during power failure and Figure 2.11.4 shows the setting of relevant registers.
Reset released
Power failure detected
XIN
XCIN
Internal system clock
Middle-speed mode
High-speed mode
Low-speed mode
Change internal system clock to high-speed mode
After detection, change internal system clock to low-speed mode and stop oscillating XIN-XOUT
XCIN-XCOUT oscillation function selected
Fig. 2.11.3 Status transition diagram during power failure
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-146
APPLICATION 3804 Group (Spec.H) 2.11 Clock generating circuit
b7
b0
CPUM 0 0 0 0 1
00
CPU mode register (CPUM) (address 003B16)
Main clock: High-speed mode (f(XIN)/2) (Note 1)
b7
b0
CPUM 0 0 0 1 1
(Note 2)
00
CPU mode register (CPUM) (address 003B16)
Port XC: XCIN-XCOUT oscillation function
b7
b0
CPUM 1 0 0 1 1
00
CPU mode register (CPUM) (address 003B16)
Internal system clock: Low-speed mode (f(XCIN)/2)
b7
b0
CPUM 1 0 1 1 1
00
CPU mode register (CPUM) (address 003B16)
Main clock f(XIN): Stopped
Notes 1: This setting is necessary only when selecting the high-speed mode. 2: When selecting the middle-speed mode, bit 6 is "1".
Fig. 2.11.4 Setting of relevant registers
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-147
APPLICATION 3804 Group (Spec.H) 2.11 Clock generating circuit
Control procedure: To prepare for a power failure, set the relevant registers in the order shown below.
RESET
qX: This bit is not used here. Set it to "0" or "1" arbitrarily.
Initialization
CPUM (address 003B16), bit7, bit 6 CPUM (address 003B16), bit 4
CPUM (address 003B16), bit7, bit 6 CPUM (address 003B16), bit5
Set timer interrupt to occurs every second. Execute WIT instruction.
****
0, 0 1 When selecting main clock f(XIN)/2 (high-speed mode) Port XC: XCIN-XCOUT oscillation function
****
Detect power failure ? Y 1, 0 (Note) 1 (Note) Internal system clock: f(XCIN)/2 (low-speed mode) Main clock f(XIN) oscillation stopped N At power failure, clock count is performed during timer interrupt processing (every second).
N
Return condition from power failure completed ? Y Return processing from power failure Note: Do not switch simultaneously.
Fig. 2.11.5 Control procedure
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-148
APPLICATION 3804 Group (Spec.H) 2.12 Standby function
2.12 Standby function
The 3804 group (Spec. H) is provided with standby functions to stop the CPU by software and put the CPU into the low-power operation. The following two types of standby functions are available. *Stop mode using STP instruction *Wait mode using WIT instruction 2.12.1 Stop mode The stop mode is set by executing the STP instruction. In the stop mode, the oscillation of both clocks (XIN- XOUT, XCIN-XCOUT) stop and the internal clock stops at the "H" level. The CPU stops and peripheral units stop operating. As a result, power dissipation is reduced. (1) State in stop mode Table 2.12.1 shows the state in the stop mode. Table 2.12.1 State in stop mode Item Oscillation CPU Internal clock I/O ports P0-P6 Timer Stopped. Stopped. Stopped at "H" level. Retains the state at the STP instruction execution. Stopped. (Timers 1, 2, X, Y, Z) However, Timers X, Y, Z can be operated in the event counter mode. Stopped. Stopped. Stopped. However, these can be operated only when an external clock is selected. I 2C-BUS interface A/D converter D/A converter Stopped. Stopped. Retains output voltage. State in stop mode
PWM Watchdog timer Serial I/O1, Serial I/O2, Serial I/O3
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-149
APPLICATION 3804 Group (Spec.H) 2.12 Standby function
(2) Release of stop mode The stop mode is released by a reset input or by the occurrence of an interrupt request. Note the differences in the restoration process according to reset input or interrupt request, as described below. sRestoration by reset input The stop mode is released by holding the RESET pin to the "L" input level during the stop mode. Oscillation is started when all ports are in the input state and the stop mode of the main clock (XINXOUT) is released. Oscillation is unstable when restarted. For this reason, time for stabilizing of oscillation (oscillation stabilizing time) is required. The input of the RESET pin should be held at the "L" level until oscillation stabilizes. When the RESET pin is held at the "L" level for 16 cycles or more of XIN after the oscillation has stabilized, the microcomputer will go to the reset state. After the input level of the RESET pin is returned to "H", the reset state is released in approximately 10.5 to 18.5 cycles of the XIN input. Figure 2.12.1 shows the oscillation stabilizing time at restoration by reset input. At release of the stop mode by reset input, the internal RAM retains its contents previous to the reset. However, the previous contents of the CPU register and SFR are not retained. For more details concerning reset, refer to "2.10 Reset".
Stop mode
Oscillation 16 cycles or stabilizing time more of XIN
Operating mode
Vcc
Time to hold internal reset state = approximately 10.5 to 18.5 cycles of XIN input
RESET XIN
(Note) Execute Stop instruction
Note: Some cases may occur in which no waveform is input to XIN (in low-speed mode).
Fig. 2.12.1 Oscillation stabilizing time at restoration by reset input
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-150
APPLICATION 3804 Group (Spec.H) 2.12 Standby function
sRestoration by interrupt request The occurrence of an interrupt request in the stop mode releases the stop mode. As a result, oscillation is resumed. The interrupts available for restoration are: *INT0-INT4 *CNTR0, CNTR1, CNTR2 *Serial I/O (1, 2, 3) using an external clock *Timer X, Y, Z using an external event count *SCL/SDA However, when using any of these interrupt requests for restoration from the stop mode, in order to enable the selected interrupt, you must execute the STP instruction after setting the following conditions. [Necessary register setting] Interrupt disable flag I = "0" (interrupt enabled) Timer 1 interrupt enable bit = "0" (interrupt disabled) Interrupt request bit of interrupt source to be used for restoration = "0" (no interrupt request issued) Interrupt enable bit of interrupt source to be used for restoration = "1" (interrupts enabled) For more details concerning interrupts, refer to "2.2 Interrupts". Oscillation is unstable when restarted. For this reason, time for stabilizing of oscillation (oscillation stabilizing time) is required. For restoration by an interrupt request, waiting time prior to supplying internal clock to the CPU is automatically generated2 by Prescaler 12 and Timer 11. This waiting time is reserved as the oscillation stabilizing time on the system clock side. The supply of internal clock to the CPU is started at the Timer 1 underflow. Figure 2.12.2 shows an execution sequence example at restoration by the occurrence of an INT0 interrupt request. 1: If the STP instruction is executed when the oscillation stabilizing time set after STP instruction released bit is "0", "FF16" and "0116" are automatically set in the Prescaler 12 counter/latch and Timer 1 counter/latch, respectively. When the oscillation stabilizing time set after STP instruction released bit is "1", nothing is automatically set to either Prescaler 12 or Timer 1. For this reason, any suitable value can be set to Prescaler 12 and Timer 1 for the oscillation stabilizing time. 2: Immediately after the oscillation is started, the count source is supplied to the prescaler 12 so that a count operation is started.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-151
APPLICATION 3804 Group (Spec.H) 2.12 Standby function
qWhen restoring microcomputer from stop mode by INT0 interrupt (oscillation stabilizing time set after STP instruction released bit = "0", rising edge selected) Stop mode XIN or XCIN (System clock) INT0 pin "FF16" Prescaler 12 counter Timer 1 counter "0116" 512 counts Oscillation stabilizing time
XIN; "H" XCIN; in high-impedance state
INT0 interrupt request bit Peripheral device CPU Stopped Stopped Operating Operating
Operating
Operating
Execute STP instruction
INT0 interrupt signal input (INT0 interrupt request occurs) Oscillation start Prescaler 12 count start
512 counts down by prescaler 12 Start supplying internal clock to CPU Accept INT0 interrupt request
Note: The count source set at STP instruction execution is connected as the prescaler 12 count source.
Fig. 2.12.2 Execution sequence example at restoration by occurrence of INT0 interrupt request (3) Notes on using stop mode sRegister setting Since values of the prescaler 12 and Timer 1 are automatically reloaded when returning from the stop mode, set them again, respectively. (When the oscillation stabilizing time set after STP instruction released bit is "0") sClock restoration After restoration from the stop mode to the normal mode by an interrupt request, the contents of the CPU mode register previous to the STP instruction execution are retained. Accordingly, if both main clock and sub clock were oscillating before execution of the STP instruction, the oscillation of both clocks is resumed at restoration. In the above case, when the main clock side is set as a system clock, the oscillation stabilizing time until the timer 1 underflow is reserved at restoration from the stop mode. When the oscillation stabilizing time set after STP instruction released bit is "0", the time for 512 counts of the count source become the oscillation stabilizing time. When the oscillation stabilizing time set after STP instruction released bit is "1", an arbitrarily count value set to the prescaler 12 and the timer 1 become the oscillation stabilizing time. At this time, note that the oscillation on the sub clock side may not be stabilized even after the lapse of the oscillation stabilizing time of the main clock side.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-152
APPLICATION 3804 Group (Spec.H) 2.12 Standby function
2.12.2 Wait mode The wait mode is set by execution of the WIT instruction. In the wait mode, oscillation continues, but the internal clock stops at the "H" level. The CPU stops, but most of the peripheral units continue operating. (1) State in wait mode The continuation of oscillation permits clock supply to the peripheral units. Table 2.12.2 shows the state in the wait mode. Table 2.12.2 State in wait mode Item Oscillation CPU Internal clock I/O ports P0-P6 Timer PWM Watchdog timer Serial I/O1, Serial I/O2, Serial I/O3 I C-BUS interface A/D converter D/A converter
2
State in wait mode Operating. Stopped. Stopped at "H" level. Retains the state at the WIT instruction execution. Operating. Operating. Operating. Operating. Stopped. Operating. Retains output voltage.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-153
APPLICATION 3804 Group (Spec.H) 2.12 Standby function
(2) Release of wait mode The wait mode is released by reset input or by the occurrence of an interrupt request. Note the differences in the restoration process according to reset input or interrupt request, as described below. In the wait mode, oscillation is continued, so an instruction can be executed immediately after the wait mode is released. sRestoration by reset input The wait mode is released by holding the input level of the RESET pin at "L" in the wait mode. Upon release of the wait mode, all ports are in the input state, and supply of the internal clock to the CPU is started. To reset the microcomputer, the RESET pin should be held at an "L" level for 16 cycles or more of XIN. The reset state is released in approximately 10.5 cycles to 18.5 cycles of the XIN input after the input of the RESET pin is returned to the "H" level. At release of wait mode, the internal RAM retains its contents previous to the reset. However, the previous contents of the CPU register and SFR are not retained. Figure 2.12.3 shows the reset input time. For more details concerning reset, refer to "2.10 Reset".
Wait mode
Operating mode
Vcc
16 cycles of XIN Time to hold internal reset state = approximately 10.5 to 18.5 cycles of XIN input
RESET XIN
(Note) Execute WIT instruction Note: Some cases may occur in which no waveform is input to XIN (in low-speed mode).
Fig. 2.12.3 Reset input time
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-154
APPLICATION 3804 Group (Spec.H) 2.12 Standby function
sRestoration by interrupt request In the wait mode, the occurrence of an interrupt request releases the wait mode and supply of the internal clock to the CPU is started. At the same time, the interrupt request used for restoration is accepted, so the interrupt processing routine is executed. However, when using an interrupt request for restoration from the wait mode, in order to enable the selected interrupt, you must execute the STP instruction after setting the following conditions. [Necessary register setting] Interrupt disable flag I = "0" (interrupt enabled) Interrupt request bit of interrupt source to be used for restoration = "0" (no interrupt request issued) Interrupt enable bit of interrupt source to be used for restoration = "1" (interrupts enabled) For more details concerning interrupts, refer to "2.2 Interrupts". (3) Notes on wait mode sClock restoration If the wait mode is released by a reset when XCIN is set as the system clock and XIN oscillation is stopped during execution of the WIT instruction, XCIN oscillation stops, XIN oscillations starts, and XIN is set as the system clock. In the above case, the RESET pin should be held at "L" until the oscillation is stabilized.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-155
APPLICATION 3804 Group (Spec.H) 2.13 Flash memory mode
2.13 Flash memory mode
This paragraph explains the registers setting method and the notes relevant to the flash memory mode of M38049FFHSP/FP/HP/KP. 2.13.1 Overview The functions of the flash memory version are similar to those of the mask ROM version except that the flash memory is built-in and some of the SFR area differ from that of the mask ROM version (refer to "2.13.2 Memory map"). In the flash memory version, the built-in flash memory can be programmed or erased by using the following three modes. * CPU rewrite mode * Parallel I/O mode * Standard serial I/O mode 2.13.2 Memory map M38049FFHSP/FP/HP/KP have 60 Kbytes of built-in flash memory. Figure 2.13.1 shows the memory map of the flash memory version.
000016 SFR area 004016 RAM 083F16 Internal RAM area (2 Kbytes) 100016 180016 200016
User ROM area Data block B: 2 Kbytes Data block A: 2 Kbytes
Block 3: 24 Kbytes Notes 1: The boot ROM area can be rewritten in a parallel I/O mode. (Access to except boot ROM area is disabled.) 2: To specify a block, use the maximum address in the block.
0FE016 0FFF16 100016 SFR area
800016
Block 2: 16 Kbytes C00016 Block 1: 8 Kbytes
Internal flash memory area (60 Kbytes)
E00016 Block 0: 8 Kbytes
F00016 Boot ROM area 4 Kbytes FFFF16
FFFF16
FFFF16
Fig. 2.13.1 Memory map of M38049FFHSP/FP/HP/KP
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-156
APPLICATION 3804 Group (Spec.H) 2.13 Flash memory mode
2.13.3 Relevant registers
Address
0FE016 Flash memory control register 0 (FMCR0) 0FE116 Flash memory control register 1 (FMCR1) 0FE216 Flash memory control register 2 (FMCR2)
Fig. 2.13.2 Memory map of registers relevant to flash memory
Flash memory control register 0
b7 b6 b5 b4 b3 b2 b1 b0 Flash memory control register 0 (FMCR0 : address 0FE016)
b
Name
Functions
0 : Busy (being automatic written or automatic erased) 1 : Ready
At reset R W
1
0 RY/BY status flag
1 CPU rewrite mode select bit (Note 1)
2
3 4 5 6 7
0 : CPU rewrite mode invalid (software commandes invalid) 1 : CPU rewrite mode valid (Software commands acceptable) 8 KB user block E/W 0: E/W disabled enable bit (Notes 1, 1: E/W enabled 2) Flash memory reset 0: Normal operation bit (Notes 3, 4) 1: Reset Not used (Do not write "1" to this bit.) User ROM area 0: User ROM area is accessed select bit (Note 5) 1: Boot ROM area is accessed Program status flag 0: Pass 1: Error Erase status flag 0: Pass 1: Error
0
0
0 0 0 0 0
Notes 1: For this bit to be set to "1", the user needs to write a "0" and then a "1" to it in succession. For this bit to be set to "0", write "0" only to this bit. 2: This bit can be written only when the CPU rewrite mode select bit is "1". 3: Effective only when the CPU rewrite mode select bit = "1". Fix this bit to "0" when the CPU rewrite mode select bit is "0". 4: When setting this bit to "1" (when the control circuit of flash memory is reset), the flash memory cannot be accessed for 10 s. 5: Write to this bit from program on RAM.
Fig. 2.13.3 Structure of Flash memory control register 0
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-157
APPLICATION 3804 Group (Spec.H) 2.13 Flash memory mode
Flash memory control register 1
b7 b6 b5 b4 b3 b2 b1 b0 Flash memory control register 1 (FMCR1 : address 0FE116)
b
Name
Functions
At reset R W
0 0
0 : Suspend invalid 0 Erase suspend enable bit (Note 1) 1 : Suspend valid 1 Erase suspend 0 : Erase restart (no request issued) request bit (Note 2) 1 : Suspend request (request issued) 2 Nothing is arranged for these bits. If writing to 3 these bits, write "0". The contents are undefined 4 at reading. 5 0 : Erase active 6 Erase suspend flag 1 : Erase inactive (Erase suspend mode) 7 Nothing is arranged for these bits. If writing to these bits, write "0". The contents are undefined at reading.
0 0 0 0 1
0
Notes 1: For this bit to be set to "1", the user needs to write a "0" and then a "1" to it in succession. 2: Only when the erase suspend bit is "1", this bit is valid.
Fig. 2.13.4 Structure of Flash memory control register 1
Flash memory control register 2
b7 b6 b5 b4 b3 b2 b1 b0 Flash memory control register 2 (FMCR2 : address 0FE216)
b
0 1 2 3 4
Name
Functions
At reset R W
1 0 1 0 0
Nothing is arranged for these bits. If writing to these bits, write "0". The contents are undefined at reading.
All user block E/W 0 : E/W disabled enable bit (Notes 1, 2) 1 : E/W enabled 0 5 Nothing is arranged for these bits. If writing to 6 these bits, write "0". The contents are undefined 1 7 at reading. 0 Notes 1: For this bit to be set to "1", the user needs to write a "0" and then a "1" to it in succession. 2: Effective only when the CPU rewrite mode select bit = "1".
Fig. 2.13.5 Structure of Flash memory control register 2
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-158
APPLICATION 3804 Group (Spec.H) 2.13 Flash memory mode
2.13.4 Parallel I/O mode In the parallel I/O mode, program/erase to the built-in flash memory can be performed by a flash memory programmer (EFP-I etc.). The memory area of program/erase is from 0F00016 to 0FFFF16 (boot ROM area) or from 0100016 to 0FFFF16 (user ROM area). Be especially careful when erasing; if the memory area is not set correctly, the products will be damaged eternally. Table 2.13.1 shows the parallel unit when programming by EFP-I in the parallel I/O mode. *EFP-I provided by Suisei Electronics System Co., Ltd. (http://www.suisei.co.jp/index_e.htm) (product available in Asia and Oceania only) Table 2.13.1 Parallel unit when parallel programming (when using EFP-I provided by Suisei Electronics System Co., Ltd.) Products M38049FFHSP M38049FFHFP M38049FFHHP M38049FFHKP Parallel unit EF3803F-64S EF3803F-64F EF3803F-64H EF3803F-64U Boot ROM area User ROM area
0F00016 to 0FFFF16
0100016 to 0FFFF16
2.13.5 Standard serial I/O mode Table 2.13.2 shows a pin connection example (4 wires) between the programmer (EFP-I; Serial unit EF1SRP-01U is required additionally) and the microcomputer when programming in the standard serial I/O mode 1. *EFP-I provided by Suisei Electronics System Co., Ltd. (http://www.suisei.co.jp/index_e.htm) (product available in Asia and Oceania only) Table 2.13.2 Connection example to programmer when serial programming (4 wires) Function Transfer clock input Serial data input Serial data output Transmit/Receive enable output "H" input Reset input Target board power source monitor input GND T_VPP T_RESET T_VDD (Note 2) GND (Note 3) 3 14 4 1, 2, 15, 16 CNVSS RESET (Note 1) VCC (Note 2) VSS, AVSS (Note 3) 26 27 1 32, 3 18 19 57 24, 59 EFP-I (EF1SRP-01U) EF1RP-01U side Signal name connector Line number T_SCLK T_TXD T_RXD T_BUSY 9 10 11 12 Flash memory version Pin name P46/SCLK1 P44/RxD1 P45/TxD1 P47/SRDY1/CNTR2 M38049FFHSP M38049FFHSP pin number pin number 13 21 23 22 20 15 14 12
Notes 1: Since reset release after write verification is not performed, when operating MCU after writing, separate a target connection cable. 2: Supply Vcc of EFP-I side from user side so that the power supply voltage of the output buffer used by the EFP-I side becomes the same as user side power supply voltage (Vcc). 3: Four pins (No. 1, 2, 15, and 16) of the EF1SRP-01U side connector are prepared for GND signal. When connecting with a target board, although connection of only one pin does not have a problem, we recommend connecting with two or more pins.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-159
APPLICATION 3804 Group (Spec.H) 2.13 Flash memory mode
2.13.6 CPU rewrite mode In the CPU rewrite mode, issuing software commands through the Central Processing Unit (CPU) can rewrite the built-in flash memory. Accordingly, the contents of the built-in flash memory can be rewritten with the microcomputer itself mounted on board, without using the programmer. Store the rewrite control program to the built-in flash memory in advance. The built-in flash memory cannot be read in the CPU rewrite mode. Accordingly, after transferring the rewrite control program to RAM, execute it on the RAM. The following commands can be used in the CPU rewrite mode: read array, read status register, clear status register, program, and block erase. For details concerning each command, refer to "CHAPTER 1 Flash memory mode (CPU rewrite mode)". (1) CPU rewrite mode beginning/release procedures Operation procedure in the CPU rewrite mode for the built-in flash memory is described below. [Beginning procedure] Apply "H" to the CNVSS pin and P45/TxD1 pin (at selecting boot ROM area). Release reset. Set bits 6 and 7 (main clock division ratio selection bits) of the CPU mode register. (Make sure that system clock is less than 4.0 MHz.) After CPU rewrite mode control program is transferred to internal RAM, jump to this control program on RAM. (The following operations are controlled by this control program). Set "1" to the CPU rewrite mode select bit (bit 1 of address 0FFE16). For this bit to be set to "1", the user needs to write "0" and then "1" to it in succession. Set "1" to the all user block E/W enable bit (bit 4 of address 0FE216). Set the 8 KB user block E/W enable bit. (Set to "0" when E/W is disabled, and set to "1" when E/W is enabled.) For these bits to be set to "1", the user needs to write "0" and then "1" to those in succession. Flash memory operations are executed by using software commands. Note 1: The following procedures are also necessary. * Control for data which is input from the external (serial I/O etc.) and to be programmed to the flash memory. * Initial setting for ports, etc. * Writing to the watchdog timer [Release procedure] Execute the read array command. In order to disable E/W to the user ROM area (except for data block), set "0" to the all user block E/ W enable bit (bit 4 of 0FE216) and the 8 KB user block E/W enable bit (bit 2 of 0FE016) (Note 2). Set the CPU rewrite mode select bit (bit 1 of address 0FFE16) to "0". Jump from the CPU rewriting control program on RAM to the user program on the flash memory. Note 2: Although E/W inhibition is not indispensable, the safety of system improves by disabling E/W except the time of E/W execution.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-160
APPLICATION 3804 Group (Spec.H) 2.13 Flash memory mode
Also, execute the following processing before the CPU reprogramming mode is selected so that interrupts will not occur during the CPU reprogramming mode. * Set the interrupt disable flag (I) to "1" When the watchdog timer has already started, write to the watchdog timer control register (address 001E16) periodically during the CPU reprogramming mode in order not to generate the reset by the underflow of the watchdog timer H. During the program or erase execution, watchdog timer is automatically cleared. Accordingly, the inernal reset by underflow does not occur. When the interrupt request or reset occurs in the CPU reprogramming mode, the microcomputer enters the following state; * Interrupt occurs This may cause a program runaway because the read from the flash memory which has the interrupt vector area cannot be performed. * Underflow of watchdog timer H, reset This may cause a microcomputer reset; the built-in flash memory control circuit and the flash memory control register are reset. When reset state is released with CNVss = "H" and P45/TxD1 = "H", CPU starts in the boot mode. Also, when the above interrupt and reset occur during program/erase, error data may still exist after reset release because the reprogramming of the flash memory is not completed, so that reprogramming of the flash memory in the parallel I/O mode or serial I/O mode is required.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-161
APPLICATION 3804 Group (Spec.H) 2.13 Flash memory mode
2.13.7 Flash memory mode application examples The control pin processing example on the system board in the standard serial I/O mode and the control example in the CPU rewrite mode are described below. (1) Control pin connection example on system board in standard serial I/O mode As shown in Figure 2.13.6, in the standard serial I/O mode, the built-in flash memory can be rewritten with the microcomputer mounted on board. Connection examples of control pins (P44/RxD, P45/TxD, P46/SCLK1, P47/SRDY1/CNTR2, CNVSS, and RESET pin) in the standard serial I/O mode are described below.
RS-232C Serial programmer
M3
80
49
FF
HS
P/
FP
/H
P/
KP
Fig. 2.13.6 Rewrite example of built-in flash memory in standard serial I/O mode
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-162
APPLICATION 3804 Group (Spec.H) 2.13 Flash memory mode
When control signals are not affected to user system circuit When the control signals in the standard serial I/O mode are not used or not affected to the user system circuit, they can be connected as shown in Figure 2.13.7.
Target board
1 Not used or to user system circuit
M38049FFHSP/FP/HP/KP
2
TXD(P45) SCLK1(P46) RXD(P44) BUSY(P47) CNVSS
VCC AVSS VSS
RESET
User reset signal (Low active)
XIN
XOUT
1: When not used, set to input mode and pull up or pull down, or set to output mode and open. 2: It is necessary to apply Vcc to SCLK1 (P46) pin only when reset is released in the serial I/O mode 1. It is necessary to apply Vss to SCLK1 (P46) pin only when reset is released in the serial I/O mode 2.
Fig. 2.13.7 Connection example in standard serial I/O mode (1) When control signals are affected to user system circuit-1 Figure 2.13.8 shows an example that the jumper switch cut-off the control signals not to supply to the user system circuit in the standard serial I/O mode.
Target board
To user system circuit
M38049FFHSP/FP/HP/KP
TXD(P45) SCLK1(P46) RXD(P44) BUSY(P47) CNVSS RESET
User reset signal (Low active)
VCC
AVSS VSS XIN XOUT
: It is necessary to apply Vcc to SCLK1 (P46) pin only when reset is released in the serial I/O mode 1. It is necessary to apply Vss to SCLK1 (P46) pin only when reset is released in the serial I/O mode 2.
Fig. 2.13.8 Connection example in standard serial I/O mode (2)
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-163
APPLICATION 3804 Group (Spec.H) 2.13 Flash memory mode
When control signals are affected to user system circuit-2 Figure 2.13.9 shows an example that the analog switch (74HC4066) cut-off the control signals not to supply to the user system circuit in the standard serial I/O mode.
Target board
74HC4066
To user system circuit
M38049FFHSP/FP/HP/KP
TXD(P45) SCLK1(P46) RXD(P44) BUSY(P47) CNVss RESET
User reset signal (Low active)
VCC
AVSS VSS XIN XOUT
: It is necessary to apply Vcc to SCLK1 (P46) pin only when reset is released in the serial I/O mode 1. It is necessary to apply Vss to SCLK1 (P46) pin only when reset is released in the serial I/O mode 2.
Fig. 2.13.9 Connection example in standard serial I/O mode (3)
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-164
APPLICATION 3804 Group (Spec.H) 2.13 Flash memory mode
(2) Control pin termination example in CPU rewrite mode In this example, data is received by using serial I/O, and the data is programmed to the built-in flash memory in the CPU rewrite mode. Figure 2.13.10 shows an example of the reprogramming system for the built-in flash memory in the CPU rewrite mode. For the CPU rewrite mode beginning/release method, refer to "2.13.6 CPU rewrite mode."
M38049FFHSP/FP/HP/KP
Clock input BUSY output Data input Data output
SCLK1 SRDY1(BUSY) RXD TXD
VCC AVSS VSS
RESET CNVSS User reset signal XIN XOUT
Fig. 2.13.10 Example of rewrite system for built-in flash memory in CPU rewrite mode (single-chip mode)
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-165
APPLICATION 3804 Group (Spec.H) 2.13 Flash memory mode
2.13.8 Notes on CPU rewrite mode (1) Operation speed During CPU rewrite mode, set the system clock 4.0 MHz or less using the main clock division ratio selection bits (bits 6 and 7 of address 003B16). (2) Instructions inhibited against use The instructions which refer to the internal data of the flash memory cannot be used during the CPU rewrite mode. (3) Interrupts inhibited against use The interrupts cannot be used during the CPU rewrite mode because they refer to the internal data of the flash memory. (4) Watchdog timer In case of the watchdog timer has been running already, the internal reset generated by watchdog timer underflow does not happen, because of watchdog timer is always clearing during program or erase operation. (5) Reset Reset is always valid. In case of CNVSS = "H" when reset is released, boot mode is active. So the program starts from the address contained in address FFFC16 and FFFD16 in boot ROM area.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
2-166
CHAPTER 3 APPENDIX
3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 3.10 Electrical characteristics Standard characteristics Notes on use Countermeasures against noise List of registers Package outline Machine instructions List of instruction code SFR memory map Pin configurations
APPENDIX 3804 Group (Spec.H) 3.1 Electrical characteristics
3.1 ELECTRICAL CHARACTERISTICS 3.1.1 Absolute maximum ratings
Table 3.1.1 Absolute maximum ratings Symbol Parameter VCC Power source voltages Input voltage P00-P07, P10-P17, P20-P27, VI P30, P31, P34-P37, P40-P47, P50-P57, P60-P67, VREF VI Input voltage P32, P33 ____________ VI Input voltage RESET, XIN VI Input voltage CNVSS VO Output voltage P00-P07, P10-P17, P20-P27, P30, P31, P34-P37, P40-P47, P50-P57, P60-P67, XOUT VO Output voltage P32, P33 Pd Power dissipation Topr Operating temperature Storage temperature Tstg Note: This value is 300 mW except SP package.
Conditions All voltages are based on Vss. Output transistors are cut off.
Ratings -0.3 to 6.5 -0.3 to VCC +0.3
Unit V V
-0.3 to 5.8 -0.3 to VCC +0.3 -0.3 to VCC +0.3 -0.3 to VCC +0.3
V V V V
Ta = 25C
-0.3 to 5.8 1000 (Note) -20 to 85 -65 to 125
V mW C C
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-2
APPENDIX 3804 Group (Spec.H) 3.1 Electrical characteristics
3.1.2 Recommended operating conditions
Table 3.1.2 Recommended operating conditions (1) (VCC = 2.7 to 5.5 V, VSS = 0V, Ta = -20 to 85 C, unless otherwise noted) Symbol VCC Parameter Power source voltage (Note 1) Conditions When start oscillating (Note 2) High-speed mode f(XIN) 8.4 MHz f() = f(XIN)/2 f(XIN) 12.5 MHz f(XIN) 16.8 MHz f(XIN) 12.5 MHz Middle-speed mode f(XIN) 16.8 MHz f() = f(XIN)/8 Min. 2.7 2.7 4.0 4.5 2.7 4.5 0.8VCC Limits Typ. 5.0 5.0 5.0 5.0 5.0 5.0 0 Max. 5.5 5.5 5.5 5.5 5.5 5.5 VCC Unit V V V V V V V V
VSS VIH
VIH VIH
VIH
VIH VIH VIL
VIL
VIL
Power source voltage "H" input voltage P00-P07, P10-P17, P20-P27, P30, P31, P34-P37, P40-P47, P50-P57, P60-P67 "H" input voltage P32, P33 "H" input voltage (when I2C-BUS input level is selected) SDA, SCL "H" input voltage (when SMBUS input level is selected) SDA, SCL "H" input voltage ____________ RESET, XIN, CNVSS "H" input voltage XCIN "L" input voltage P00-P07, P10-P17, P20-P27, P30-P37,P40-P47, P50-P57, P60-P67 "L" input voltage (when I2C-BUS input level is selected) SDA, SCL "L" input voltage (when SMBUS input level is selected) SDA, SCL
____________
0.8VCC 0.7VCC
5.5 5.5
V V
1.4
5.5
V
0.8VCC 2 0
VCC VCC 0.2VCC
V V V
0
0.3Vcc
V
0
0.6
V
VIL VIL VIL
"L" input voltage RESET, CNVSS "L" input voltage XIN "L" input voltage XCIN
0
0.2VCC 0.16VCC 0.4
V V V
Notes 1: When using A/D converter, see A/D converter recommended operating conditions. 2: The start voltage and the start time for oscillation depend on the using oscillator, oscillation circuit constant value and operating temperature range, etc.. Particularly a high-frequency oscillator might require some notes in the low voltage operation.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-3
APPENDIX 3804 Group (Spec.H)
Table 3.1.3 Recommended operating conditions (2) (VCC = 2.7 to 5.5 V, VSS = 0V, Ta = -20 to 85 C, unless otherwise noted) Symbol f(XIN) Parameter Main clock input oscillation frequency (Note 1) Conditions High-speed mode f() = f(XIN)/2 2.7 VCC < 4.0 V 4.0 VCC < 4.5 V 4.5 VCC 5.5 V 2.7 VCC < 4.5 V 4.5 VCC 5.5 V f(XCIN) Sub-clock input oscillation frequency (Notes 1, 2) 32.768 Limits Min. Typ. Max. (9VCC-0.3)1.05 3 (24VCC-60)1.05 3 16.8 (15VCC+39)1.1 7 16.8 50 Unit MHz MHz MHz MHz MHz kHz
3.1 Electrical characteristics
Middle-speed mode f() = f(XIN)/8
Notes 1: When the oscillation frequency has a duty cycle of 50%. 2: When using the microcomputer in low-speed mode, set the sub-clock input oscillation frequency on condition that f(XCIN) < f(XIN)/3.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-4
APPENDIX 3804 Group (Spec.H)
Table 3.1.4 Recommended operating conditions (3) (VCC = 2.7 to 5.5 V, VSS = 0V, Ta = -20 to 85 C, unless otherwise noted) Symbol IOH(peak) IOH(peak) IOL(peak) IOL(peak) IOL(peak) IOH(avg) IOH(avg) IOL(avg) IOL(avg) IOL(avg) IOH(peak) IOL(peak) IOL(peak) IOH(avg) IOL(avg) IOL(avg) "H" total peak output current "H" total peak output current "L" total peak output current "L" total peak output current "L" total peak output current "H" total average output current "H" total average output current "L" total average output current "L" total average output current "L" total average output current "H" peak output current "L" peak output current "L" peak output current "H" average output current "L" average output current "L" average output current Parameter P00-P07, P10-P17, P20-P27, P30, P31, P34-P37 (Note 1) P40-P47, P50-P57, P60-P67 (Note 1) P00-P07, P10-P17, P30-P37 (Note 1) P20-P27 (Note 1) P40-P47,P50-P57, P60-P67 (Note 1) P00-P07, P10-P17, P20-P27, P30, P31, P34-P37 (Note 1) P40-P47,P50-P57, P60-P67 (Note 1) P00-P07, P10-P17, P30-P37 (Note 1) P20-P27 (Note 1) P40-P47,P50-P57, P60-P67 (Note 1) P00-P07, P10-P17, P20-P27, P30, P31, P34-P37, P40-P47, P50-P57, P60-P67 (Note 2) P00-P07, P10-P17, P30-P37, P40-P47, P50-P57, P60-P67 (Note 2) P20-P27 (Note 2) P00-P07, P10-P17, P20-P27, P30, P31, P34-P37, P40-P47, P50-P57, P60-P67 (Note 3) P00-P07, P10-P17, P30-P37, P40-P47, P50-P57, P60-P67 (Note 3) P20-P27 (Note 3) Min. Limits Typ. Max. -80 -80 80 80 80 -40 -40 40 40 40 -10 10 20 -5 5 10 Unit mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA
3.1 Electrical characteristics
Notes 1: The total output current is the sum of all the currents flowing through all the applicable ports. The total average current is an average value measured over 100 ms. The total peak current is the peak value of all the currents. 2: The peak output current is the peak current flowing in each port. 3: The average output current IOL(avg), IOH(avg) are average value measured over 100 ms.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-5
APPENDIX 3804 Group (Spec.H) 3.1 Electrical characteristics
3.1.3 Electrical characteristics
Table 3.1.5 Electrical characteristics (1) (VCC = 2.7 to 5.5 V, VSS = 0V, Ta = -20 to 85 C, unless otherwise noted) Symbol VOH Parameter "H" output voltage P00-P07, P10-P17, P20-P27, P30, P31, P34-P37, P40-P47, P50-P57, P60-P67 (Note 1) "L" output voltage P00-P07, P10-P17, P20-P27, P30-P37, P40-P47, P50-P57, P60-P67 "L" output voltage P20-P27 Test conditions IOH = -10 mA VCC = 4.0 to 5.5 V IOH = -1.0 mA VCC = 1.8 to 5.5 V IOL = 10 mA VCC = 4.0 to 5.5 V IOL = 1.6 mA VCC = 1.8 to 5.5 V IOL = 20 mA VCC = 4.0 to 5.5 V IOL = 1.6 mA VCC = 1.8 to 5.5 V Limits Min. VCC-2.0 VCC-1.0 2.0 1.0 2.0 0.4 0.4 Typ. Max. Unit V V V V V V V
VOL
VOL
VT+-VT-
VT+-VT-
VT+-VT- IIH
IIH IIH IIL
IIL IIL IIL
VRAM
Hysteresis CNTR0, CNTR1, CNTR2, INT0-INT4 Hysteresis RxD1, SCLK1, SIN2, SCLK2, RxD3, SCLK3 ____________ Hysteresis RESET "H" input current P00-P07, P10-P17, P20-P27, P30-P37, P40-P47, P50-P57, P60-P67 ____________ "H" input current RESET, CNVSS "H" input current XIN "L" input current P00-P07, P10-P17, P20-P27, P30-P37, P40-P47, P50-P57, P60-P67 ____________ "L" input current RESET,CNVSS "L" input current XIN "L" input current (at Pull-up) P00-P07, P10-P17, P20-P27, P30, P31, P34-P37, P40-P47, P50-P57, P60-P67 RAM hold voltage
0.5
V
0.5 VI = VCC (Pin floating. Pull-up transistors "off") VI = VCC VI = VCC VI = VSS (Pin floating. Pull-up transistors "off") VI = VSS VI = VSS VI = VSS VCC = 5.0 V VI = VSS VCC = 3.0 V When clock stopped 5.0
V A
5.0 4.0 -5.0
A A A
-5.0 -80 -30 1.8 -4.0 -210 -70 -420 -140 VCC
A A A A V
Note 1: P35 is measured when the P35/TxD3 P-channel output disable bit of the UART3 control register (bit 4 of address 003316) is "0". P45 is measured when the P45/TxD1 P-channel output disable bit of the UART1 control register (bit 4 of address 001B16) is "0".
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-6
APPENDIX 3804 Group (Spec.H) 3.1 Electrical characteristics
Table 3.1.6 Electrical characteristics (2) (VCC = 2.7 to 5.5 V, Ta = -20 to 85 C, f(XCIN)=32.768kHZ (Stoped in middle-speed mode), Output transistors "off", AD converter not operated) Limits Symbol ICC Parameter Power source current High-speed mode VCC = 5V Test conditions f(XIN) = 16.8 MHz f(XIN) = 12.5 MHz f(XIN) = 8.4 MHz f(XIN) = 4.2 MHz f(XIN) = 16.8 MHz (in WIT state) f(XIN) = 8.4 MHz f(XIN) = 4.2 MHz f(XIN) = 2.1 MHz f(XIN) = 16.8 MHz f(XIN) = 12.5 MHz f(XIN) = 8.4 MHz f(XIN) = 16.8 MHz (in WIT state) f(XIN) = 12.5 MHz f(XIN) = 8.4 MHz f(XIN) = 6.3 MHz f(XIN) = stopped In WIT state f(XIN) = stopped In WIT state Ta = 25 C Ta = 85 C f(XIN) = 16.8 MHz, VCC = 5V In Middle-, high-speed mode Min. Typ. 5.5 4.5 3.5 2.2 2.2 2.7 1.8 1.1 3.0 2.4 2.0 2.1 1.7 1.5 1.3 410 4.5 400 3.7 0.55 0.75 1000 Max. 8,3 6.8 5.3 3.3 3.3 4.1 2.7 1.7 4.5 3.6 3.0 3.2 2.6 2.3 2.0 630 6.8 600 5.6 3.0 Unit mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA A A A A A A A
VCC = 3V
Middle-speed mode
VCC = 5V
VCC = 3V
Low-speed mode
VCC = 5V VCC = 3V
In STP state (All oscillation stopped) Increment when A/D conversion is executed
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-7
APPENDIX 3804 Group (Spec.H) 3.1 Electrical characteristics
3.1.4 A/D converter characteristics
Table 3.1.7 A/D converter recommended operating conditions (VCC = 2.7 to 5.5 V, VSS = AVSS = 0 V,Ta = -20 to 85 C, unless otherwise noted) Symbol VCC VREF AVSS VIA f(XIN) Parameter Power source voltage (When A/D converter is used) Analog reference voltage Analog power source voltage Analog input voltage Main clock oscillation frequency (When A/D converter is used) Conditions 8-bit A/D mode (Note 1) 10-bit A/D mode (Note 2) Limits Min. 2.7 2.7 2.0 0 0.5 0.5 0.5 Typ. 5.0 5.0 0 2.7 VCC < 4.0 V 4.0 VCC < 4.5 V 4.5 VCC 5.5 V
Note 1: 8-bit A/D mode: When the conversion mode selection bit (bit 7 of address 003816) is "1". 2: 10-bit A/D mode: When the conversion mode selection bit (bit 7 of address 003816) is "0".
Max. 5.5 5.5 VCC VCC (9VCC-0.3)1.05 3 (24VCC-60)1.05 3 16.8
Unit V V V V MHZ
Table 3.1.8 A/D converter characteristics (VCC = 2.7 to 5.5 V, VSS = AVSS = 0 V, Ta = -20 to 85 C, unless otherwise noted) Symbol - - tCONV Resolution Absolute accuracy (excluding quantization error) Conversion time Parameter Test conditions 8-bit A/D mode (Note 1) 10-bit A/D mode (Note 2) 8-bit A/D mode (Note 1) 10-bit A/D mode (Note 2) 8-bit A/D mode (Note 1) 10-bit A/D mode (Note 2) Min. Limits Typ. Max. 8 10 2 4 50 61 100 200 5 5 Unit bit LSB 2tc(XIN) k A A A
2.7 VREF 5.5 V 2.7 VREF 5.5 V
RLADDER Ladder resistor IVREF Reference power at A/D converter operated VREF = 5.0 V source input current at A/D converter stopped VREF = 5.0 V II(AD) A/D port inout current
Note 1: 8-bit A/D mode: When the conversion mode selection bit (bit 7 of address 003816) is "1". 2: 10-bit A/D mode: When the conversion mode selection bit (bit 7 of address 003816) is "0".
12 50
35 150
3.1.5 D/A converter characteristics
Table 3.1.9 D/A converter characteristics (VCC = 2.7 to 5.5 V, VREF = 2.7 V to VCC, VSS = AVSS = 0 V, Ta = -20 to 85 C, unless otherwise noted) Symbol - - tsu RO IVREF Resolution Absolute accuracy Parameter 4.0 VREF 5.5 V 2.7 VREF < 4.0 V 2 3.5 Test conditions Limits Min. Typ. Max. 8 1.0 2.5 3 5 3.2 Unit bit % % s k mA
Setting time Output resistor Reference power source input current (Note 1)
Note 1: Using one D/A converter, with the value in the DA conversion register of the other D/A converter being "0016".
3.1.6 Power source circuit timing characteristics
Table 3.1.10 Power source circuit timing characteristics (VCC = 2.7 to 5.5 V, VREF = 2.7 V to VCC, VSS = AVSS = 0 V, Ta = -20 to 85 C, unless otherwise noted) Symbol td(P-R) Parameter Internal power source stable time at power-on Test conditions 2.7 Vcc < 5.5 V Limits Min. Typ. Max. 2 Unit ms
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-8
APPENDIX 3804 Group (Spec.H) 3.1 Electrical characteristics
3.1.7 Timing requirements and switching characteristics
Table 3.1.11 Timing requirements (1) (VCC = 2.7 to 5.5 V, VSS = 0V, Ta = -20 to 85 C, unless otherwise noted) Symbol tW(RESET) tC(XIN) Reset input "L" pulse width Main clock XIN input cycle time Main clock XIN input "H" pulse width Main clock XIN input "L" pulse width Sub-clock XCIN input cycle time Sub-clock XCIN input "H" pulse width Sub-clock XCIN input "L" pulse width CNTR0-CNTR2 input cycle time CNTR0-CNTR2 input "H" pulse width CNTR0-CNTR2 input "L" pulse width INT00, INT01, INT1, INT2, INT3, INT40, INT41 input "H" pulse width INT00, INT01, INT1, INT2, INT3, INT40, INT41 input "L" pulse width Parameter Limits Min. 4.5VCC5.5 V 4.0VCC<4.5 V 2.7VCC<4.0 V 4.5VCC5.5 V 4.0VCC<4.5 V 2.7VCC<4.0 V 4.5VCC5.5 V 4.0VCC<4.5 V 2.7VCC<4.0 V td(P-R) ms + 16 59.5 10000/(86VCC-219) 26103/(82VCC-3) 25 4000/(86VCC-219) 10000/(82VCC-3) 25 4000/(86VCC-219) 10000/(82VCC-3) 20 5 5 120 160 250 48 64 115 48 64 115 48 64 115 48 64 115 Typ. Max. Unit XIN cycle ns
tWH(XIN)
ns
tWL(XIN)
ns
tC(XCIN) tWH(XCIN) tWL(XCIN) tC(CNTR)
4.5VCC5.5 V 4.0VCC<4.5 V 2.7VCC<4.0 V 4.5VCC5.5 V 4.0VCC<4.5 V 2.7VCC<4.0 V 4.5VCC5.5 V 4.0VCC<4.5 V 2.7VCC<4.0 V 4.5VCC5.5 V 4.0VCC<4.5 V 2.7VCC<4.0 V 4.5VCC5.5 V 4.0VCC<4.5 V 2.7VCC<4.0 V
s s s ns
tWH(CNTR)
ns
tWL(CNTR)
ns
tWH(INT)
ns
tWL(INT)
ns
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-9
APPENDIX 3804 Group (Spec.H)
Table 3.1.12 Timing requirements (2) (VCC = 2.7 to 5.5 V, VSS = 0V, Ta = -20 to 85 C, unless otherwise noted) Symbol tC(SCLK1), tC(SCLK3) Serial I/O1, serial I/O3 clock input cycle time (Note) Serial I/O1, serial I/O3 clock input "H" pulse width (Note) Serial I/O1, serial I/O3 clock input "L" pulse width (Note) Serial I/O1, serial I/O3 clock input setup time Serial I/O1, serial I/O3 clock input hold time Serial I/O2 clock input cycle time Serial I/O2 clock input "H" pulse width Serial I/O2 clock input "L" pulse width Serial I/O2 clock input setup time Serial I/O2 clock input hold time Parameter 4.5VCC5.5 V 4.0VCC<4.5 V 2.7VCC<4.0 V 4.5VCC5.5 V 4.0VCC<4.5 V 2.7VCC<4.0 V 4.5VCC5.5 V 4.0VCC<4.5 V 2.7VCC<4.0 V 4.5VCC5.5 V 4.0VCC<4.5 V 2.7VCC<4.0 V 4.5VCC5.5 V 4.0VCC<4.5 V 2.7VCC<4.0 V 4.5VCC5.5 V 4.0VCC<4.5 V 2.7VCC<4.0 V 4.5VCC5.5 V 4.0VCC<4.5 V 2.7VCC<4.0 V 4.5VCC5.5 V 4.0VCC<4.5 V 2.7VCC<4.0 V 4.5VCC5.5 V 4.0VCC<4.5 V 2.7VCC<4.0 V 4.5VCC5.5 V 4.0VCC<4.5 V 2.7VCC<4.0 V Min. 250 320 500 120 150 240 120 150 240 70 90 100 32 40 50 500 650 1000 200 260 400 200 260 400 100 130 200 100 130 150 Limits Typ. Max. Unit ns
3.1 Electrical characteristics
tWH(SCLK1), tWH(SCLK3)
ns
tWL(SCLK1), tWL(SCLK3)
ns
tsu(RxD1-SCLK1), tsu(RxD3-SCLK3) th(SCLK1-RxD1), th(SCLK3-RxD3) tC(SCLK2)
ns
ns
ns
tWH(SCLK2)
ns
tWL(SCLK2)
ns
tsu(SIN2-SCLK2)
ns
th(SCLK2-SIN2)
ns
Note : When bit 6 of address 001A16 and bit 6 of address 003216 are "1" (clock synchronous). Divide this value by four when bit 6 of address 001A16 and bit 6 of address 003216 are "0" (UART).
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-10
APPENDIX 3804 Group (Spec.H)
Table 3.1.13 Switching characteristics (VCC = 2.7 to 5.5 V, VSS = 0V, Ta = -20 to 85 C, unless otherwise noted) Symbol tWH(SCLK1) tWH(SCLK3) tWL(SCLK1) tWL(SCLK3) td(SCLK1-TxD1) td(SCLK3-TxD3) tV(SCLK1-TxD1) tV(SCLK3-TxD3) tr(SCLK1) tr(SCLK3) tf(SCLK1) tf(SCLK3) tWH(SCLK2) Parameter Serial I/O1, serial I/O3 clock output "H" pulse width Serial I/O1, serial I/O3 clock output "L" pulse width Serial I/O1, serial I/O3 output delay time (Note) Serial I/O1, serial I/O3 output valid time (Note) Serial I/O1, serial I/O3 rise time of clock output Serial I/O1, serial I/O3 fall time of clock output Serial I/O2 clock output "H" pulse width Serial I/O2 clock output "L" pulse width Serial I/O2 output delay time Serial I/O2 output valid time Serial I/O2 fall time of clock output CMOS rise time of output (Note) CMOS fall time of output (Note) 4.5VCC5.5 V 4.0VCC<4.5 V 2.7VCC<4.0 V 4.5VCC5.5 V 4.0VCC<4.5 V 2.7VCC<4.0 V 4.5VCC5.5 V 4.0VCC<4.5 V 2.7VCC<4.0 V 4.5VCC5.5 V 4.0VCC<4.5 V 2.7VCC<4.0 V 4.5VCC5.5 V 4.0VCC<4.5 V 2.7VCC<4.0 V 4.5VCC5.5 V 4.0VCC<4.5 V 2.7VCC<4.0 V 4.5VCC5.5 V 4.0VCC<4.5 V 2.7VCC<4.0 V 4.5VCC5.5 V 4.0VCC<4.5 V 2.7VCC<4.0 V 4.5VCC5.5 V 4.0VCC<4.5 V 2.7VCC<4.0 V 4.5VCC5.5 V 4.0VCC<4.5 V 2.7VCC<4.0 V 4.5VCC5.5 V 4.0VCC<4.5 V 2.7VCC<4.0 V 4.5VCC5.5 V 4.0VCC<4.5 V 2.7VCC<4.0 V 4.5VCC5.5 V 4.0VCC<4.5 V 2.7VCC<4.0 V Test conditions Limits Min. tC(SCLK1)2-30, tC(SCLK3)/2-30 tC(SCLK1)2-35, tC(SCLK3)/2-35 tC(SCLK1)2-40, tC(SCLK3)/2-40 tC(SCLK1)2-30, tC(SCLK3)/2-30 tC(SCLK1)2-35, tC(SCLK3)/2-35 tC(SCLK1)2-40, tC(SCLK3)/2-40 Typ. Max. Unit ns
3.1 Electrical characteristics
ns
140 200 350 -30 -30 -30 30 35 40 30 35 40 tC(SCLK2)/2-160 tC(SCLK2)/2-200 tC(SCLK2)/2-240 tC(SCLK2)/2-160 tC(SCLK2)/2-200 tC(SCLK2)/2-240 200 250 300 0 0 0 30 35 40 30 35 40 30 35 40
ns
ns
ns
ns
Fig. 3.1.1
ns
tWL(SCLK2)
ns
td(SCLK2-SOUT2)
ns
tV(SCLK2-SOUT2)
ns
tf(SCLK2)
ns
tr(CMOS)
tf(CMOS)
10 12 15 10 12 15
ns
ns
Note: When the P45/TxD1 P-channel output disable bit of the UART1 control register (bit 4 of address 001B16) is "0".
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-11
APPENDIX 3804 Group (Spec.H) 3.1 Electrical characteristics
Measurement output pin 100pF
Measurement output pin
1k
100pF
CMOS output
N-channel open-drain output
Fig. 3.1.1 Circuit for measuring output switching characteristics (1)
Fig. 3.1.2 Circuit for measuring output switching characteristics (2)
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-12
APPENDIX 3804 Group (Spec.H) 3.1 Electrical characteristics
Single-chip mode timing diagram
tC(CNTR) tWH(CNTR) tWL(CNTR) 0.2VCC
CNTR0, CNTR1, CNTR2
0.8VCC
INT1,INT2,INT3 INT00,INT40 INT01,INT41
tWH(INT) 0.8VCC 0.2VCC
tWL(INT)
tW(RESET)
RESET
0.2VCC
0.8VCC
tC(XIN) tWH(XIN) tWL(XIN) 0.2VCC
XIN
0.8VCC
tC(XCIN) tWH(XCIN) tWL(XCIN) 0.2VCC
XCIN
0.8VCC
tC(SCLK1), tC(SCLK2),tC(SCLK3),
SCLK1 SCLK2 SCLK3
tf
tWL(SC LK1), tW L(SC LK2), tWL(SC LK3) 0.2VCC tsu(RxD1-SCLK1), tsu(SIN2-SCLK2), tsu(RxD3-SCLK3)
tr
tWH (SC LK1), tWH (SC LK2), tWH (SC LK3) 0.8VCC th(SCLK1-RxD1), th(SCLK2-SIN2), th(SCLK3-RxD3)
RXD1 RXD3 SIN2 TXD1 TXD3 SOUT2
Fig. 3.1.3 Timing diagram (in single-chip mode)
0.8VCC 0.2VCC td(SC LK1-TxD1), td(SC LK2-SOUT2), td(SC LK3-TxD3) tv(SC LK1-TxD1), tv(SC LK2-SOUT2), tv(SC LK3-TxD3)
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-13
APPENDIX 3804 Group (Spec.H) 3.1 Electrical characteristics
3.1.8 Multi-master I2C-BUS bus line characteristics
Table 3.1.14 Multi-master I 2C-BUS bus line characteristics Standard clock mode High-speed clock mode Symbol tBUF tHD;STA tLOW tR tHD;DAT tHIGH tF tSU;DAT tSU;STA tSU;STO Bus free time Hold time for START condition Hold time for SCL clock = "0" Rising time of both SCL and SDA signals Data hold time Hold time for SCL clock = "1" Falling time of both SCL and SDA signals Data setup time Setup time for repeated START condition Setup time for STOP condition 250 4.7 4.0 0 4.0 300 Parameter Min. 4.7 4.0 4.7 1000 Max. Min. 1.3 0.6 1.3 20+0.1Cb 0 0.6 20+0.1Cb 100 0.6 0.6 300 300 0.9 Max. Unit s s s ns s s ns ns s s
Note: Cb = total capacitance of 1 bus line
S DA
tBUF tLOW tR tF
Sr P
tHD:STA
tsu:STO
SCL
P
S
tHD:STA
tHD:DAT
tHIGH
tsu:DAT
tsu:STA
S : START condition Sr: RESTART condition P : STOP condition
Fig. 3.1.4 Timing diagram of multi-master I2C-BUS
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-14
APPENDIX 3804 Group (Spec.H) 3.2 Standard characteristics
3.2 Standard characteristics
Standard characteristics described below are just examples of the 3804 Group (spec. H)'s characteristics and are not guaranteed. For rated values, refer to "3.1 Electrical characteristics". 3.2.1 Power source current standard characteristics
High-speed mode (TYP, 25 C) [ = XIN/2, XCIN = 32.768 kHz]
8.0
6.0
Icc (mA)
4.0
2.0
0.0 2.5 3.0
16.8 MHz
3.5
12.5 MHz
4.0 4.5 Vcc (V)
8.4 MHz
5.0
4.2 MHz
5.5
2.1 MHz
6.0
Fig. 3.2.1 Power source current standard characteristics (in high-speed mode)
Middle-speed mode (TYP, 25 C) [ = XIN/8, XCIN = stopped]
4.0
3.0
Icc (mA)
2.0
1.0
0.0 2.5 3.0
16.8 MHz
3.5
4.0 4.5 Vcc (V)
12.5 MHz 8.4 MHz
5.0
5.5
6.3 MHz
6.0
Fig. 3.2.2 Power source current standard characteristics (in middle-speed mode)
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-15
APPENDIX 3804 Group (Spec.H) 3.2 Standard characteristics
Low-speed mode (TYP, 25 C) [ = XCIN/2, XIN = stopped]
800.0
600.0
Icc (A)
400.0
200.0
0.0 2.5 3.0 3.5 4.0 4.5 Vcc (V)
32.768 kHz
5.0
5.5
6.0
Fig. 3.2.3 Power source current standard characteristics (in low-speed mode)
High-speed mode, WAIT state (TYP, 25 C) [ = XIN/2, XCIN = 32.768 kHz]
8.0
6.0
Icc (mA)
4.0
2.0
0.0 2.5 3.0 3.5 4.0 4.5 Vcc (V)
16.8 MHz
5.0
5.5
6.0
Fig. 3.2.4 Power source current standard characteristics (in high-speed mode, f(XIN) = 16.8 MHz, WAIT state)
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-16
APPENDIX 3804 Group (Spec.H) 3.2 Standard characteristics
Middle-speed mode, WAIT state (TYP, 25 C) [ = XIN/8, XCIN = stopped]
4.0
3.0
Icc (mA)
2.0
1.0
0.0 2.5 3.0 3.5 4.0 4.5 Vcc (V)
16.8 MHz
5.0
5.5
6.0
Fig. 3.2.5 Power source current standard characteristics (in middle-speed mode, f(XIN) = 16.8 MHz, WAIT state)
Low-speed mode, WAIT state (TYP, 25 C) [ = XCIN/2, XIN = stopped, XCIN = 32.768 kHz]
8.0
6.0
Icc (A)
4.0
2.0
0.0 2.5 3.0 3.5 4.0 4.5 Vcc (V) 5.0 5.5 6.0
32.768 kHz
Fig. 3.2.6 Power source current standard characteristics (in low-speed mode, WAIT state)
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-17
APPENDIX 3804 Group (Spec.H) 3.2 Standard characteristics
High-speed mode, A/D converter operating (TYP, 25 C) [ = XIN/2, XCIN = 32.768 kHz]
8.0
6.0
)
4.0
Icc (mA) (
2.0
0.0 2.5 3.0 3.5 4.0 4.5 VCC(V)
16.8 MHz
5.0
5.5
6.0
Fig. 3.2.7 Power source current standard characteristics (in high-speed mode, f(XIN) = 16.8 MHz, A/D converter operating)
Oscillation stop mode (TYP, 25 C) [STP instruction executing, XIN = stopped, XCIN = stopped]
1.0 0.8
0.6
Icc (A)
0.4
0.2 0.0 2.5 3.0 3.5 4.0 4.5 Vcc (V)
Stopped
5.0
5.5
6.0
Fig. 3.2.8 Power source current standard characteristics (at oscillation stopping)
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-18
APPENDIX 3804 Group (Spec.H) 3.2 Standard characteristics
3.2.2 Port standard characteristics
Port P60 IOH-VOH characteristics (P-channel drive) [Ta = 25 C] (Same characteristics pins: P0, P1, P2, P30, P31, P34-P37, P4, P5, P6)
-50 -45 -40 -35
Vcc = 5.0 V Vcc = 4.0V
IOH -30 [mA] -25
-20 -15 -10 -5 0 0 0.5 1.0 1.5
Vcc = 2.7V
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
VOH [V]
Fig. 3.2.9 CMOS output port P-channel side characteristics (Ta = 25 C)
Port P60 IOL-VOL characteristics (N-channel drive) [Ta = 25 C] (Same characteristics pins: P0, P1, P3, P4, P5, P6)
50 45 40 35
Vcc = 5.0 V
IOL [mA]
30 25 20 15 10 5 0 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5
Vcc = 4.0 V
Vcc = 2.7 V
VOL[V]
Fig. 3.2.10 CMOS output port N-channel side characteristics (Ta = 25 C)
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-19
APPENDIX 3804 Group (Spec.H) 3.2 Standard characteristics
Port P32 IOL-VOL characteristics (N-channel drive) [Ta = 25 C] (Same characteristics pins: P32, P33)
50 45 40 35
Vcc = 5.0 V
IOL [mA]
30 25 20 15 10 5 0 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5
Vcc = 4.0 V
Vcc = 2.7 V
VOL[V]
Fig. 3.2.11 N-channel open-drain output port N-channel side characteristics (Ta = 25 C)
Port P20 IOL-VOL characteristics (N-channel drive) [Ta = 25 C] (Same characteristics pins: P2)
100 90 80 70
Vcc = 5.0 V
IOL [mA]
60 50 40 30 20 10 0 0 0.5 1.0 1.5 2.0 2.5 3.0
Vcc = 4.0 V
Vcc = 2.7 V
3.5
4.0
4.5
5.0
5.5
VOL[V]
Fig. 3.2.12 CMOS large current output port N-channel side characteristics (Ta = 25 C)
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-20
APPENDIX 3804 Group (Spec.H) 3.2 Standard characteristics
Port P60 IIL-VIL characteristics (at pull-up) [Ta = 25 C] (Same characteristics pins: P0, P1, P2, P30, P31, P34-P37, P4, P5, P6)
-400 -360 -320 -280
Vcc = 6.0 V Vcc = 5.0 V
IIL -240 [mA] -200
-160 -120 -80 -40 0 0 0.5 1.0 1.5
Vcc = 3.0 V
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
VIL[V]
Fig. 3.2.13 CMOS input port at pull-up characteristics (Ta = 25 C)
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-21
APPENDIX 3804 Group (Spec.H) 3.2 Standard characteristics
3.2.3 A/D conversion standard characteristics Figure3.2.14, Figure 3.2.15, and Figure 3.2.16 show the A/D conversion standard characteristics. The thick lines of the graph indicate the absolute precision errors, These are expressed as the deviation from the ideal value when the output code changes. For example, the change in output code from 512 to 513 should occur at 2560 mV, but the measured value is -10 mV. Accordingly, the measured point of change is 2560 - 10 = 2550 mV. The thin lines of the graph indicate the input voltage width for which the output code is constant. For example, the measured input voltage width for which the output code is 512 is 5.0 mV, so that the differential non-linear error is 5.0 - 5.0 = 0.0 mV (0 LSB).
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-22
APPENDIX 3804 Group (Spec.H) 3.2 Standard characteristics
M38049FFHSP A/D CONV. ERROR & STEP WIDTH
VDD = 5.12 [V], VREF = 5.12 [V] XIN = 8 [MHz], Ta = 25 [deg.] Error 1 LSB Width
Fig. 3.2.14 A/D conversion standard characteristics (f(XIN) = 8 MHz)
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-23
APPENDIX 3804 Group (Spec.H) 3.2 Standard characteristics
M38049FFHSP A/D CONV. ERROR & STEP WIDTH
VDD = 5.12 [V], VREF = 5.12 [V] XIN = 12 [MHz], Ta = 25 [deg.] Error 1 LSB Width
Fig. 3.2.15 A/D conversion standard characteristics (f(XIN) = 12 MHz)
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-24
APPENDIX 3804 Group (Spec.H) 3.2 Standard characteristics
M38049FFHSP A/D CONV. ERROR & STEP WIDTH
VDD = 5.12 [V], VREF = 5.12 [V] XIN = 16 [MHz], Ta = 25 [deg.] Error 1 LSB Width
Fig. 3.2.16 A/D conversion standard characteristics (f(XIN) = 16 MHz)
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-25
APPENDIX 3804 Group (Spec.H) 3.2 Standard characteristics
3.2.4 D/A conversion standard characteristics Figure 3.2.17 shows the D/A conversion standard characteristics.
M38049FFHSP D/A CONV. STEP WIDTH MEASUREMENT
VCC = 5.12 [V], VREF = 5.12 [V] XIN = 16 [MHz], Ta = 25 [deg.] Error 1 LSB Width
Fig. 3.2.17 D/A conversion standard characteristics
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-26
APPENDIX 3804 Group (Spec.H) 3.3 Notes on use
3.3 Notes on use
3.3.1 Notes on input and output ports (1) Notes in standby state In standby state 1 for low-power dissipation, do not make input levels of an I/O port "undefined". Even when an I/O port of N-channel open-drain is set as output mode, if output data is "1", the aforementioned notes are necessary. Pull-up (connect the port to VCC) or pull-down (connect the port to VSS) these ports through a resistor. When determining a resistance value, note the following points: * External circuit * Variation of output levels during the ordinary operation When using built-in pull-up resistor, note on varied current values: * When setting as an input port : Fix its input level * When setting as an output port : Prevent current from flowing out to external q Reason Exclusive input ports are always in a high-impedance state. An output transistor becomes an OFF state when an I/O port is set as input mode by the direction register, so that the port enter a highimpedance state. At this time, the potential which is input to the input buffer in a microcomputer is unstable in the state that input levels are "undefined". This may cause power source current. Even when an I/O port of N-channel open-drain is set as output mode by the direction register, if the contents of the port latch is "1", the same phenomenon as that of an input port will occur. 1 standby state: Stop mode by executing STP instruction Wait mode by executing WIT instruction (2) Modifying output data with bit managing instruction When the port latch of an I/O port is modified with the bit managing instruction 2, the value of the unspecified bit may be changed. q Reason The bit managing instructions are read-modify-write form instructions for reading and writing data by a byte unit. Accordingly, when these instructions are executed on a bit of the port latch of an I/O port, the following is executed to all bits of the port latch. *As for bit which is set for input port: The pin state is read in the CPU, and is written to this bit after bit managing. *As for bit which is set for output port: The bit value is read in the CPU, and is written to this bit after bit managing. Note the following: *Even when a port which is set as an output port is changed for an input port, its port latch holds the output data. *As for a bit of which is set for an input port, its value may be changed even when not specified with a bit managing instruction in case where the pin state differs from its port latch contents. 2 Bit managing instructions: SEB and CLB instructions
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-27
APPENDIX 3804 Group (Spec.H) 3.3 Notes on use
3.3.2 Termination of unused pins (1) Terminate unused pins I/O ports : * Set the I/O ports for the input mode and connect them to VCC or VSS through each resistor of 1 k to 10 k. Ports that permit the selecting of a built-in pull-up resistor can also use this resistor. Set the I/O ports for the output mode and open them at "L" or "H". * When opening them in the output mode, the input mode of the initial status remains until the mode of the ports is switched over to the output mode by the program after reset. Thus, the potential at these pins is undefined and the power source current may increase in the input mode. With regard to an effects on the system, thoroughly perform system evaluation on the user side. * Since the direction register setup may be changed because of a program runaway or noise, set direction registers by program periodically to increase the reliability of program. The AVss pin when not using the A/D converter : * When not using the A/D converter, handle a power source pin for the A/D converter, AVss pin as follows: AVss: Connect to the Vss pin. (2) Termination remarks I/O ports : Do not open in the input mode. q Reason * The power source current may increase depending on the first-stage circuit. * An effect due to noise may be easily produced as compared with proper termination and shown on the above. I/O ports : When setting for the input mode, do not connect to VCC or VSS directly. q Reason If the direction register setup changes for the output mode because of a program runaway or noise, a short circuit may occur between a port and VCC (or VSS). I/O ports : When setting for the input mode, do not connect multiple ports in a lump to VCC or VSS through a resistor. q Reason If the direction register setup changes for the output mode because of a program runaway or noise, a short circuit may occur between ports. * At the termination of unused pins, perform wiring at the shortest possible distance (20 mm or less) from microcomputer pins.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-28
APPENDIX 3804 Group (Spec.H) 3.3 Notes on use
3.3.3 Notes on interrupts (1) Change of relevant register settings When the setting of the following registers or bits is changed, the interrupt request bit may be set to "1". When not requiring the interrupt occurrence synchronized with these setting, take the following sequence. *Interrupt edge selection register (address 003A16) *Timer XY mode register (address 002316) *Timer Z mode register (address 002A16) *I 2C START/STOP condition control register (address 001616) Set the above listed registers or bits as the following sequence.
Set the corresponding interrupt enable bit to "0" (disabled) . Set the interrupt edge select bit (active edge switch bit) or the interrupt (source) select bit to "1". NOP (One or more instructions) Set the corresponding interrupt request bit to "0" (no interrupt request issued). Set the corresponding interrupt enable bit to "1" (enabled).
Fig. 3.3.1 Sequence of changing relevant register s Reason When setting the followings, the interrupt request bit may be set to "1". *When setting external interrupt active edge Concerned register: Interrupt edge selection register (address 003A16) Timer XY mode register (address 002316) Timer Z mode register (address 002A16) I 2C START/STOP condition control register (address 001616) *When switching interrupt sources of an interrupt vector address where two or more interrupt sources are allocated. Concerned register: Interrupt source selection register (address 003916) (2) Check of interrupt request bit q When executing the BBC or BBS instruction to an interrupt request bit of an interrupt request register immediately after this bit is set to "0", execute one or more instructions before executing the BBC or BBS instruction.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-29
APPENDIX 3804 Group (Spec.H) 3.3 Notes on use
s Reason If the BBC or BBS instruction is executed immediately after an interrupt request bit of an interrupt request register is cleared to "0", the value of the interrupt request bit before being cleared to "0" is read.
Clear the interrupt request bit to "0" (no interrupt issued) NOP (one or more instructions) Execute the BBC or BBS instruction Fig. 3.3.2 Sequence of check of interrupt request bit
3.3.4 Notes on 8-bit timer (timer 1, 2, X, Y) q If a value n (between 0 and 255) is written to a timer latch, the frequency division ratio is 1/(n+1). q When switching the count source by the timer 12, X and Y count source selection bits, the value of timer count is altered in unconsiderable amount owing to generating of thin pulses in the count input signals. Therefore, select the timer count source before set the value to the prescaler and the timer. q Set the double-function port of the CNTR0/CNTR1 pin and port P54/P55 to output in the pulse output mode. q Set the double-function port of CNTR0/CNTR1 pin and port P54/P55 to input in the event counter mode and the pulse width measurement mode. 3.3.5 Notes on 16-bit timer (timer Z) (1) Pulse output mode q Set the double-function port of the CNTR2 pin and port P47 to output. (2) Pulse period measurement mode q Set the double-function port of the CNTR2 pin and port P47 to input. q A read-out of timer value is impossible in this mode. The timer can be written to only during timer stop (no measurement of pulse period). q Since the timer latch in this mode is specialized for the read-out of measured values, do not perform any write operation during measurement. q "FFFF16" is set to the timer when the timer underflows or when the valid edge of measurement start/completion is detected. Consequently, the timer value at start of pulse period measurement depends on the timer value just before measurement start. (3) Pulse width measurement mode q Set the double-function port of the CNTR2 pin and port P47 to input. q A read-out of timer value is impossible in this mode. The timer can be written to only during timer stop (no measurement of pulse period). q Since the timer latch in this mode is specialized for the read-out of measured values, do not perform any write operation during measurement. q "FFFF16" is set to the timer when the timer underflows or when the valid edge of measurement start/completion is detected. Consequently, the timer value at start of pulse width measurement depends on the timer value just before measurement start.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-30
APPENDIX 3804 Group (Spec.H) 3.3 Notes on use
(4) Programmable waveform generating mode q Set the double-function port of the CNTR2 pin and port P47 to output. (5) Programmable one-shot generating mode q Set the double-function port of CNTR2 pin and port P47 to output, and of INT1 pin and port P42 to input in this mode. q This mode cannot be used in low-speed mode. q If the value of the CNTR2 active edge switch bit is changed during one-shot generating enabled or generating one-shot pulse, then the output level from CNTR2 pin changes. (6) All modes qTimer Z write control Which write control can be selected by the timer Z write control bit (bit 3) of the timer Z mode register (address 002A16), writing data to both the latch and the timer at the same time or writing data only to the latch. When the operation "writing data only to the latch" is selected, the value is set to the timer latch by writing data to the address of timer Z and the timer is updated at next underflow. After reset release, the operation "writing data to both the latch and the timer at the same time" is selected, and the value is set to both the latch and the timer at the same time by writing data to the address of timer Z. In the case of writing data only to the latch, if writing data to the latch and an underflow are performed almost at the same time, the timer value may become undefined. qTimer Z read control A read-out of timer value is impossible in pulse period measurement mode and pulse width measurement mode. In the other modes, a read-out of timer value is possible regardless of count operating or stopped. However, a read-out of timer latch value is impossible. qSwitch of interrupt active edge of CNTR2 and INT1 Each interrupt active edge depends on setting of the CNTR2 active edge switch bit and the INT1 active edge selection bit. qSwitch of count source When switching the count source by the timer Z count source selection bits, the value of timer count is altered in inconsiderable amount owing to generating of thin pulses on the count input signals. Therefore, select the timer count source before setting the value to the prescaler and the timer.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-31
APPENDIX 3804 Group (Spec.H) 3.3 Notes on use
3.3.6 Notes on serial interface (1) Notes when selecting clock synchronous serial I/O Stop of transmission operation As for serial I/Oi (i = 1, 3) that can be used as either a clock synchronous or an asynchronous (UART) serial I/O, clear the serial I/Oi enable bit and the transmit enable bit to "0" (serial I/Oi and transmit disabled). q Reason Since transmission is not stopped and the transmission circuit is not initialized even if only the serial I/Oi enable bit is cleared to "0" (serial I/Oi disabled), the internal transmission is running (in this case, since pins TxDi, RxDi, SCLKi, and SRDYi function as I/O ports, the transmission data is not output). When data is written to the transmit buffer register in this state, data starts to be shifted to the transmit shift register. When the serial I/Oi enable bit is set to "1" at this time, the data during internally shifting is output to the TxDi pin and an operation failure occurs. Stop of receive operation As for serial I/Oi (i = 1, 3) that can be used as either a clock synchronous or an asynchronous (UART) serial I/O, clear the receive enable bit to "0" (receive disabled), or clear the serial I/Oi enable bit to "0" (serial I/Oi disabled). Stop of transmit/receive operation As for serial I/Oi (i = 1, 3) that can be used as either a clock synchronous or an asynchronous (UART) serial I/O, clear both the transmit enable bit and receive enable bit to "0" (transmit and receive disabled). (when data is transmitted and received in the clock synchronous serial I/O mode, any one of data transmission and reception cannot be stopped.) q Reason In the clock synchronous serial I/O mode, the same clock is used for transmission and reception. If any one of transmission and reception is disabled, a bit error occurs because transmission and reception cannot be synchronized. In this mode, the clock circuit of the transmission circuit also operates for data reception. Accordingly, the transmission circuit does not stop by clearing only the transmit enable bit to "0" (transmit disabled). Also, the transmission circuit is not initialized by clearing the serial I/Oi enable bit to "0" (serial I/Oi disabled) (refer to in (1) ).
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-32
APPENDIX 3804 Group (Spec.H) 3.3 Notes on use
(2) Notes when selecting clock asynchronous serial I/O Stop of transmission operation Clear the transmit enable bit to "0" (transmit disabled). The transmission operation does not stop by clearing the serial I/Oi enable bit (i = 1, 3) to "0". q Reason This is the same as in (1). Stop of receive operation Clear the receive enable bit to "0" (receive disabled). Stop of transmit/receive operation Only transmission operation is stopped. Clear the transmit enable bit to "0" (transmit disabled). The transmission operation does not stop by clearing the serial I/Oi enable bit (i = 1, 3) to "0". q Reason This is the same as in (1). Only receive operation is stopped. Clear the receive enable bit to "0" (receive disabled). (3) SRDYi (i = 1, 3) output of reception side When signals are output from the SRDYi pin on the reception side by using an external clock in the clock synchronous serial I/O mode, set all of the receive enable bit, the SRDYi output enable bit, and the transmit enable bit to "1" (transmit enabled). (4) Setting serial I/Oi (i = 1, 3) control register again Set the serial I/Oi control register again after the transmission and the reception circuits are reset by clearing both the transmit enable bit and the receive enable bit to "0." Clear both the transmit enable bit (TE) and the receive enable bit (RE) to "0" Set the bits 0 to 3 and bit 6 of the serial I/Oi control register Set both the transmit enable bit (TE) and the receive enable bit (RE), or one of them to "1"
Can be set with the LDM instruction at the same time
Fig. 3.3.3 Sequence of setting serial I/Oi (i = 1, 3) control register again (5) Data transmission control with referring to transmit shift register completion flag After the transmit data is written to the transmit buffer register, the transmit shift register completion flag changes from "1" to "0" with a delay of 0.5 to 1.5 shift clocks. When data transmission is controlled with referring to the flag after writing the data to the transmit buffer register, note the delay. (6) Transmission control when external clock is selected When an external clock is used as the synchronous clock for data transmission, set the transmit enable bit to "1" at "H" of the SCLKi (i = 1, 3) input level. Also, write the transmit data to the transmit buffer register at "H" of the SCLKi input level.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-33
APPENDIX 3804 Group (Spec.H) 3.3 Notes on use
(7) Transmit interrupt request when transmit enable bit is set When using the transmit interrupt, take the following sequence. Set the serial I/Oi transmit interrupt enable bit (i = 1, 3) to "0" (disabled). Set the tranasmit enable bit to "1". Set the serial I/Oi transmit interrupt request bit (i = 1, 3) to "0" after 1 or more instruction has executed. Set the serial I/Oi transmit interrupt enable bit (i = 1, 3) to "1" (enabled). q Reason When the transmission enable bit is set to "1", the transmit buffer empty flag and transmit shift register shift completion flag are also set to "1". Therefore, regardless of selecting which timing for the generating of transmit interrupts, the interrupt request is generated and the transmit interrupt request bit is set at this point. (8) Writing to baud rate generator i (BRGi) (i = 1, 3) Write data to the baud rate generator i (BRGi) (i = 1, 3) while the transmission/reception operation is stopped. 3.3.7 Notes on multi-master I 2C-BUS interface (1) Read-modify-write instruction Each register of the multi-master I2C-BUS interface has bits to change by hardware. The precautions when the read-modify-write instruction such as SEB, CLB etc. is executed for each register of the multi-master I2C-BUS interface are described below. I 2C data shift register (S0: address 001116) When executing the read-modify-write instruction for this register during transfer, data may become a value not intended. I2C slave address registers 0 to 2 (S0D0 to S0D2: addresses 0FF716 to 0FF916) When the read-modify-write instruction is executed for this register at detecting the STOP condition, data may become a value not intended. q Reason ________ It is because hardware changes the read/write bit (RWB) at detecting the STOP condition. I 2C status register (S1: address 001316) Do not execute the read-modify-write instruction for this register because all bits of this register are changed by hardware. I 2C control register (S1D: address 001416) When the read-modify-write instruction is executed for this register at detecting the START condition or at completing the byte transfer, data may become a value not intended. q Reason Because hardware changes the bit counter (BC0 to BC2). I 2C clock control register (S2: address 001516) The read-modify-write instruction can be executed for this register. I 2C START/STOP condition control register (S2D: address 001616) The read-modify-write instruction can be executed for this register.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-34
APPENDIX 3804 Group (Spec.H) 3.3 Notes on use
(2) START condition generating procedure using multi-master Procedure example (The necessary conditions of the generating procedure are described as the following to ). LDA #SLADR (Taking out of slave address value) SEI (Interrupt disabled) BBS 5, S1, BUSBUSY (BB flag confirming and branch process) BUSFREE: STA S0 (Writing of slave address value) LDM #$F0, S1 (Trigger of START condition generating) CLI (Interrupt enabled) : : BUSBUSY: CLI (Interrupt enabled) : : Use "Branch on Bit Set" of "BBS 5, S1, -" for the BB flag confirming and branch process. Use "STA, STX" or "STY" of the zero page addressing instruction for writing the slave address value to the I 2C data shift register (S0: address 001116). Execute the branch instruction of above and the store instruction of above continuously shown by the above procedure example. Disable interrupts during the following three process steps: * BB flag confirming * Writing of slave address value * Trigger of START condition generating (3) RESTART condition generating procedure in master Procedure example (The necessary conditions of the generating procedure are described as the following to ). Execute the following procedure when the PIN bit is "0". LDM #$00, S1 (Select slave receive mode) LDA #SLADR (Taking out of slave address value) SEI (Interrupt disabled) STA S0 (Writing of slave address value) LDM #$F0, S1 (Trigger of RESTART condition generating) CLI (Interrupt enabled) : : Select the slave receive mode when the PIN bit is "0". Do not write "1" to the PIN bit. The TRX bit becomes "0" and the SDA pin is released. The SCL pin is released by writing the slave address value to the I 2C data shift register. Disable interrupts during the following two process steps: * Writing of slave address value (4) Writing to I 2C status register (S1: address 001316) Do not execute an instruction to set the PIN bit to "1" from "0" and an instruction to set the MST and TRX bits to "0" from "1" simultaneously. It is because it may enter the state that the SCL pin is released and the SDA pin is released after about one machine cycle. Do not execute an instruction to set the MST and TRX bits to "0" from "1" simultaneously when the PIN bit is "1". It is because it may become the same as above. (5) Writing to I 2C clock control register (S2: address 001516) Do not write data into the I 2C clock control register during transfer. If data is written during transfer, the I2C clock generator is reset, so that data cannot be transferred normally.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-35
APPENDIX 3804 Group (Spec.H) 3.3 Notes on use
(6) Switching of SCL/SDA interrupt pin polarity selection bit, SCL/SDA interrupt pin selection bit, I 2C-BUS interface enable bit When changing the setting of the SCL/SDA interrupt pin polarity selection bit, the SCL/SDA interrupt pin selection bit, or the I 2C-BUS interface enable bit ES0, the SCL/SDA interrupt request bit may be set. When selecting the SCL/SDA interrupt source, disable the interrupt before the SCL/SDA interrupt pin polarity selection bit, the SCL/SDA interrupt pin selection bit, or the I2C-BUS interface enable bit ES0 is set. Reset the request bit to "0" after setting these bits, and enable the interrupt. (7) Process of after STOP condition generating in master mode Do not write data in the I2C data shift register (S0) and the I2C status register (S1) until the bus busy flag BB becomes "0" after generating the STOP condition in the master mode. It is because the STOP condition waveform might not be normally generated. Reading to the above registers does not have the problem. (8) ES0 bit switch In standard clock mode when SSC = "000102" or in high-speed clock mode, flag BB may switch to "1" if ES0 bit is set to "1" when SDA is "L". Countermeasure: Set ES0 to "1" when SDA is "H". * Trigger of RESTART condition generating 3.3.8 Notes on programming for SMBUS interface (1) Time out process For a smart battery system, the time out process with a program is required so that the communication can be completed even when communication is interrupted. It is because there is possibility of extracting a battery from a PC. The specifications are defined so that communication has been able to be completed within 25 ms from START condition to STOP condition and within 10 ms from the ACK pulse to the ACK pulse of each byte. Accordingly, the following two should be considered as count start conditions. SDA falling edge caused by SCL/SDA interrupt This is the countermeasure for a communication interrupt in the middle of from START condition to a slave address. However, the detection condition must be considered because a interrupt is also generated by communication from other masters to other slaves. SMBUS interrupt after receiving slave address This is the countermeasure for when communication is interrupted from receiving a slave address until receiving a command. (2) Low hold of communication line The I2C-BUS interface conforms to the I 2C-BUS Standard Specifications. However, because the use condition of SMBUS differs from the I 2C-BUS's, there is possibility of occurrence of the following problem. Low hold of SDA line caused by ACK pulse at voltage drop of communication line When the SMBUS voltage slowly drops, that is caused by extracting a battery from equipment or turning off a PC's power or etc., it might be incorrectly treated as the SCL pulse near the threshold level voltage. When the SDA is judged "L" in that condition, it becomes the general call and the ACK is transmitted. However, when the SCL remains "L" at the ACK pulse, the SDA continuously remains "L" until input of the next SCL pulse.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-36
APPENDIX 3804 Group (Spec.H) 3.3 Notes on use
Countermeasure: As explained before, start the time out count at the falling of SDA line of START condition and reset ES0 bit of the S1D register when the time out is satisfied (Note). Note: Do not use the read-modify-write instruction at this time. Furthermore, when the ES0 bit is set to "0", it becomes a general-purpose port ; so that the port must be set to input mode or "H". 3.3.9 Notes on PWM The PWM starts from "H" level after the PWM enable bit is set to enable and "L" level is temporarily output from the PWM pin. The length of this "L" level output is as follows: n+1 2 * f(XIN) n+1 f(XIN)
(s)
(Count source selection bit = "0", where n is the value set in the prescaler)
(s)
(Count source selection bit = "1", where n is the value set in the prescaler)
3.3.10 Notes on A/D converter (1) Analog input pin Make the signal source impedance for analog input low, or equip an analog input pin with an external capacitor of 0.01 F to 1 F. Further, be sure to verify the operation of application products on the user side. q Reason An analog input pin includes the capacitor for analog voltage comparison. Accordingly, when signals from signal source with high impedance are input to an analog input pin, charge and discharge noise generates. This may cause the A/D conversion precision to be worse. (2) A/D converter power source pin The AVSS pin is A/D converter power source pins. Regardless of using the A/D conversion function or not, connect it as following : * AVSS : Connect to the VSS line q Reason If the AVSS pin is opened, the microcomputer may have a failure because of noise or others. (3) Clock frequency during A/D conversion The comparator consists of a capacity coupling, and a charge of the capacity will be lost if the clock frequency is too low. Thus, make sure the following during an A/D conversion. * f(XIN) is 500 kHz or more * Do not execute the STP instruction (4) Difference between at 8-bit reading in 10-bit A/D mode and at 8-bit A/D mode At 8-bit reading in the 10-bit A/D mode, "-1/2 LSB" correction is not performed to the A/D conversion result. In the 8-bit A/D mode, the A/D conversion characteristics is the same as 3802 group's characteristics because "-1/2 LSB" correction is performed.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-37
APPENDIX 3804 Group (Spec.H) 3.3 Notes on use
3.3.11 Notes on D/A converter (1) Vcc when using D/A converter The D/A converter accuracy when Vcc is 4.0 V or less differs from that of when Vcc is 4.0 V or more. When using the D/A converter, we recommend using a Vcc of 4.0 V or more. (2) DAi conversion register when not using D/A converter When a D/A converter is not used, set all values of the DAi conversion registers (i = 1, 2) to "0016". The initial value after reset is "0016". 3.3.12 Notes on watchdog timer qMake sure that the watchdog timer H does not underflow while waiting Stop release, because the watchdog timer keeps counting during that term. qWhen the STP instruction disable bit has been set to "1", it is impossible to switch it to "0" by a program. 3.3.13 Notes on RESET pin Connecting capacitor In case where the RESET signal rise time is long, connect a ceramic capacitor or others across the RESET pin and the VSS pin. Use a 1000 pF or more capacitor for high frequency use. When connecting the capacitor, note the following : * Make the length of the wiring which is connected to a capacitor as short as possible. * Be sure to verify the operation of application products on the user side. q Reason ____________ If the several nanosecond or several ten nanosecond impulse noise enters the RESET pin, it may cause a microcomputer failure. 3.3.14 Notes on low-speed operation mode (1) Using sub-clock To use a sub-clock, fix bit 3 of the CPU mode register to "1" or control the Rd (refer to Figure 3.3.4) resistance value to a certain level to stabilize an oscillation. For resistance value of Rd, consult the oscillator manufacturer. q Reason When bit 3 of the CPU mode register is set to "0", the sub-clock oscillation may stop.
XCIN
XCOUT
Rf
Rd
CCIN
CCOUT
Fig. 3.3.4 Ceramic resonator circuit
(2) Switch between middle/high-speed mode and low-speed mode If you switch the mode between middle/high-speed and low-speed, stabilize both XIN and XCIN oscillations. The sufficient time is required for the sub clock to stabilize, especially immediately after power on and at returning from stop mode. When switching the mode between middle/high-speed and lowspeed, set the frequency on condition that f(XIN) > 3f(XCIN).
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-38
APPENDIX 3804 Group (Spec.H) 3.3 Notes on use
3.3.15 Quartz-crystal oscillator When using the quartz-crystal oscillator of high frequency, such as 16 MHz etc., it may be necessary to select a specific oscillator with the specification demanded. 3.3.16 Notes on restarting oscillation (1) Restarting oscillation Usually, when the MCU stops the clock oscillation by STP instruction and the STP instruction has been released by an external interrupt source, the fixed values of Timer 1 and Prescaler 12 (Timer 1 = "0116", Prescaler 12 = "FF16") are automatically reloaded in order for the oscillation to stabilize. The user can inhibit the automatic setting by writing "1" to bit 0 of MISRG (address 001016). However, by setting this bit to "1", the previous values, set just before the STP instruction was executed, will remain in Timer 1 and Prescaler 12. Therefore, you will need to set an appropriate value to each register, in accordance with the oscillation stabilizing time, before executing the STP instruction. q Reason Oscillation will restart when an external interrupt is received. However, internal clock is supplied to the CPU only when Timer 1 starts to underflow. This ensures time for the clock oscillation using the ceramic resonators to be stabilized. 3.3.17 Notes on using stop mode sRegister setting Since values of the prescaler 12 and Timer 1 are automatically reloaded when returning from the stop mode, set them again, respectively. (When the oscillation stabilizing time set after STP instruction released bit is "0") sClock restoration After restoration from the stop mode to the normal mode by an interrupt request, the contents of the CPU mode register previous to the STP instruction execution are retained. Accordingly, if both main clock and sub clock were oscillating before execution of the STP instruction, the oscillation of both clocks is resumed at restoration. In the above case, when the main clock side is set as a system clock, the oscillation stabilizing time until the timer 1 underflow is reserved at restoration from the stop mode. When the oscillation stabilizing time set after STP instruction released bit is "0", the time for 512 counts of the count source become the oscillation stabilizing time. When the oscillation stabilizing time set after STP instruction released bit is "1", an arbitrarily count value set to the prescaler 12 and the timer 1 become the oscillation stabilizing time. At this time, note that the oscillation on the sub clock side may not be stabilized even after the lapse of the oscillation stabilizing time of the main clock side.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-39
APPENDIX 3804 Group (Spec.H) 3.3 Notes on use
3.3.18 Notes on wait mode sClock restoration If the wait mode is released by a reset when XCIN is set as the system clock and XIN oscillation is stopped during execution of the WIT instruction, XCIN oscillation stops, XIN oscillations starts, and XIN is set as the system clock. In the above case, the RESET pin should be held at "L" until the oscillation is stabilized. 3.3.19 Notes on CPU rewrite mode (1) Operation speed During CPU rewrite mode, set the system clock 4.0 MHz or less using the main clock division ratio selection bits (bits 6 and 7 of address 003B16). (2) Instructions inhibited against use The instructions which refer to the internal data of the flash memory cannot be used during the CPU rewrite mode. (3) Interrupts inhibited against use The interrupts cannot be used during the CPU rewrite mode because they refer to the internal data of the flash memory. (4) Watchdog timer In case of the watchdog timer has been running already, the internal reset generated by watchdog timer underflow does not happen, because of watchdog timer is always clearing during program or erase operation. (5) Reset Reset is always valid. In case of CNVSS = "H" when reset is released, boot mode is active. So the program starts from the address contained in address FFFC16 and FFFD16 in boot ROM area. 3.3.20 Notes on programming (1) Processor status register Initializing of processor status register Flags which affect program execution must be initialized after a reset. In particular, it is essential to initialize the T and D flags because they have an important effect on calculations. q Reason After a reset, the contents of the processor status register (PS) are undefined except for the I flag which is "1".
Reset Initializing of flags Main program Fig. 3.3.5 Initialization of processor status register
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-40
APPENDIX 3804 Group (Spec.H) 3.3 Notes on use
How to reference the processor status register To reference the contents of the processor status register (PS), execute the PHP instruction once then read the contents of (S+1). If necessary, execute the PLP instruction to return the PS to its original status. A NOP instruction should be executed after every PLP instruction.
PLP instruction execution NOP
(S) (S)+1 Stored PS
Fig. 3.3.6 Sequence of PLP instruction execution
Fig. 3.3.7 Stack memory contents after PHP instruction execution
(2) BRK instruction Interrupt priority level When the BRK instruction is executed with the following conditions satisfied, the interrupt execution is started from the address of interrupt vector which has the highest priority. * Interrupt request bit and interrupt enable bit are set to "1". * Interrupt disable flag (I) is set to "1" to disable interrupt. (3) Decimal calculations Execution of decimal calculations The ADC and SBC are the only instructions which will yield proper decimal notation, set the decimal mode flag (D) to "1" with the SED instruction. After executing the ADC or SBC instruction, execute another instruction before executing the SEC, CLC, or CLD instruction. Notes on status flag in decimal mode When decimal mode is selected, the values of three of the flags in the status register (the N, V, and Z flags) are invalid after a ADC or SBC instruction is executed. The carry flag (C) is set to "1" if a carry is generated as a result of the calculation, or is cleared to "0" if a borrow is generated. To determine whether a calculation has generated a carry, the C flag must be initialized to "0" before each calculation. To check for a borrow, the C flag must be initialized to "1" before each calculation.
Set D flag to "1" ADC or SBC instruction NOP instruction SEC, CLC, or CLD instruction Fig. 3.3.8 Status flag at decimal calculations
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-41
APPENDIX 3804 Group (Spec.H) 3.3 Notes on use
(4) JMP instruction When using the JMP instruction in indirect addressing mode, do not specify the last address on a page as an indirect address. (5) Multiplication and Division Instructions * The index X mode (T) and the decimal mode (D) flags do not affect the MUL and DIV instruction. * The execution of these instructions does not change the contents of the processor status register. (6) Ports The contents of the port direction registers cannot be read. The following cannot be used: * The data transfer instruction (LDA, etc.) * The operation instruction when the index X mode flag (T) is "1" * The instruction with the addressing mode which uses the value of a direction register as an index * The bit-test instruction (BBC or BBS, etc.) to a direction register * The read-modify-write instructions (ROR, CLB, or SEB, etc.) to a direction register. Use instructions such as LDM and STA, etc., to set the port direction registers. 3.3.21 Notes on flash memory version The CNVss pin determines the flash memory mode. To improve the noise reduction, connect a track between CNVss pin and Vss pin or Vcc pin with 1 to 10km resistance. The mask ROM version track of CNVss pin has no operational interference even if it is connected to Vss pin or Vcc pin via a resistor. 3.3.22 Notes on electric characteristic differences between mask ROM and flash nemory version MCUs There are differences in electric characteristics, operation margin, noise immunity, and noise radiation between Mask ROM and Flash Memory version MCUs due to the difference in the manufacturing processes, built-in ROM, and layout pattern etc. When manufacturing an application system with the Flash Memory version and then switching to use of the Mask ROM version, please conduct evaluations equivalent to the system evaluations conducted for the flash memory version. 3.3.23 Notes on handling of power source pins In order to avoid a latch-up occurrence, connect a capacitor suitable for high frequencies as bypass capacitor between power source pin (Vcc pin) and GND pin (Vss pin), and between power source pin (Vcc pin) and analog power source input pin (AVss pin). Besides, connect the capacitor to as close as possible. For bypass capacitor which should not be located too far from the pins to be connected, a ceramic capacitor of 0.01 F-0.1 F is recommended. 3.3.24 Power Source Voltage When the power source voltage value of a microcomputer is less than the value which is indicated as the recommended operating conditions, the microcomputer does not operate normally and may perform unstable operation. In a system where the power source voltage drops slowly when the power source voltage drops or the power supply is turned off, reset a microcomputer when the power source voltage is less than the recommended operating conditions and design a system not to cause errors to the system by this unstable operation.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-42
APPENDIX 3804 Group (Spec.H) 3.4 Countermeasures against noise
3.4 Countermeasures against noise
Countermeasures against noise are described below. The following countermeasures are effective against noise in theory, however, it is necessary not only to take measures as follows but to evaluate before actual use. 3.4.1 Shortest wiring length The wiring on a printed circuit board can function as an antenna which feeds noise into the microcomputer. The shorter the total wiring length (by mm unit), the less the possibility of noise insertion into a microcomputer. (1) Wiring for RESET pin Make the length of wiring which is connected to the RESET pin as short as possible. Especially, connect a capacitor across the RESET pin and the VSS pin with the shortest possible wiring (within 20 mm). q Reason The width of a pulse input into the RESET pin is determined by the timing necessary conditions. If noise having a shorter pulse width than the standard is input to the RESET pin, the reset is released before the internal state of the microcomputer is completely initialized. This may cause a program runaway.
Noise
Reset circuit VSS
N.G.
RESET VSS
Reset circuit VSS
RESET VSS
O.K.
Fig. 3.4.1 Wiring for the RESET pin
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-43
APPENDIX 3804 Group (Spec.H) 3.4 Countermeasures against noise
(2) Wiring for clock input/output pins * Make the length of wiring which is connected to clock I/O pins as short as possible. * Make the length of wiring (within 20 mm) across the grounding lead of a capacitor which is connected to an oscillator and the VSS pin of a microcomputer as short as possible. * Separate the VSS pattern only for oscillation from other VSS patterns. q Reason If noise enters clock I/O pins, clock waveforms may be deformed. This may cause a program failure or program runaway. Also, if a potential difference is caused by the noise between the VSS level of a microcomputer and the VSS level of an oscillator, the correct clock will not be input in the microcomputer.
Noise
XIN XOUT VSS
N.G.
XIN XOUT VSS
O.K.
Fig. 3.4.2 Wiring for clock I/O pins (3) Wiring to CNVss pin Connect the CNVss pin to the Vss pin with the shortest possible wiring. q Reason The processor mode of a microcomputer is influenced by a potential at the CNVss pin. If a potential difference is caused by the noise between pins CNVss and Vss, the processor mode may become unstable. This may cause a microcomputer malfunction or a program runaway.
Noise
CNVSS VSS
CNVSS VSS
N.G.
O.K.
Fig. 3.4.3 Wiring for CNVss pin
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-44
APPENDIX 3804 Group (Spec.H) 3.4 Countermeasures against noise
3.4.2 Connection of bypass capacitor across VSS line and VCC line Connect an approximately 0.1 F bypass capacitor across the VSS line and the VCC line as follows: * Connect a bypass capacitor across the VSS pin and the VCC pin at equal length. * Connect a bypass capacitor across the VSS pin and the VCC pin with the shortest possible wiring. * Use lines with a larger diameter than other signal lines for VSS line and VCC line. * Connect the power source wiring via a bypass capacitor to the VSS pin and the VCC pin.
VCC
VCC
VSS
VSS
N.G.
O.K.
Fig. 3.4.4 Bypass capacitor across the VSS line and the VCC line
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-45
APPENDIX 3804 Group (Spec.H) 3.4 Countermeasures against noise
3.4.3 Wiring to analog input pins * Connect an approximately 100 to 1 k resistor to an analog signal line which is connected to an analog input pin in series. Besides, connect the resistor to the microcomputer as close as possible. * Connect an approximately 1000 pF capacitor across the VSS pin and the analog input pin. Besides, connect the capacitor to the VSS pin as close as possible. Also, connect the capacitor across the analog input pin and the VSS pin at equal length. q Reason Signals which is input in an analog input pin (such as an A/D converter/comparator input pin) are usually output signals from sensor. The sensor which detects a change of event is installed far from the printed circuit board with a microcomputer, the wiring to an analog input pin is longer necessarily. This long wiring functions as an antenna which feeds noise into the microcomputer, which causes noise to an analog input pin. If a capacitor between an analog input pin and the VSS pin is grounded at a position far away from the VSS pin, noise on the GND line may enter a microcomputer through the capacitor.
Noise
(Note)
Microcomputer Analog input pin
Thermistor N.G. O.K.
VSS
Note : The resistor is used for dividing resistance with a thermistor.
Fig. 3.4.5 Analog signal line and a resistor and a capacitor
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-46
APPENDIX 3804 Group (Spec.H) 3.4 Countermeasures against noise
3.4.4 Oscillator concerns Take care to prevent an oscillator that generates clocks for a microcomputer operation from being affected by other signals. (1) Keeping oscillator away from large current signal lines Install a microcomputer (and especially an oscillator) as far as possible from signal lines where a current larger than the tolerance of current value flows. q Reason In the system using a microcomputer, there are signal lines for controlling motors, LEDs, and thermal heads or others. When a large current flows through those signal lines, strong noise occurs because of mutual inductance.
Microcomputer Mutual inductance M Large current GND XIN XOUT VSS
Fig. 3.4.6 Wiring for a large current signal line (2) Installing oscillator away from signal lines where potential levels change frequently Install an oscillator and a connecting pattern of an oscillator away from signal lines where potential levels change frequently. Also, do not cross such signal lines over the clock lines or the signal lines which are sensitive to noise. q Reason Signal lines where potential levels change frequently (such as the CNTR pin signal line) may affect other lines at signal rising edge or falling edge. If such lines cross over a clock line, clock waveforms may be deformed, which causes a microcomputer failure or a program runaway.
N.G.
Do not cross
CNTR XIN XOUT VSS
Fig. 3.4.7 Wiring of signal lines where potential levels change frequently
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-47
APPENDIX 3804 Group (Spec.H) 3.4 Countermeasures against noise
(3) Oscillator protection using VSS pattern As for a two-sided printed circuit board, print a VSS pattern on the underside (soldering side) of the position (on the component side) where an oscillator is mounted. Connect the VSS pattern to the microcomputer VSS pin with the shortest possible wiring. Besides, separate this VSS pattern from other VSS patterns.
An example of VSS patterns on the underside of a printed circuit board Oscillator wiring pattern example
XIN XOUT VSS
Separate the VSS line for oscillation from other VSS lines
Fig. 3.4.8 VSS pattern on the underside of an oscillator 3.4.5 Setup for I/O ports Setup I/O ports using hardware and software as follows: * Connect a resistor of 100 or more to an I/O port in series. * As for an input port, read data several times by a program for checking whether input levels are equal or not. * As for an output port, since the output data may reverse because of noise, rewrite data to its port latch at fixed periods. * Rewrite data to direction registers and pull-up control registers at fixed periods.
Noise O.K.
Data bus
Direction register N.G. Port latch I/O port pins Noise
Fig. 3.4.9 Setup for I/O ports
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-48
APPENDIX 3804 Group (Spec.H) 3.4 Countermeasures against noise
3.4.6 Providing of watchdog timer function by software If a microcomputer runs away because of noise or others, it can be detected by a software watchdog timer and the microcomputer can be reset to normal operation. This is equal to or more effective than program runaway detection by a hardware watchdog timer. The following shows an example of a watchdog timer provided by software. In the following example, to reset a microcomputer to normal operation, the main routine detects errors of the interrupt processing routine and the interrupt processing routine detects errors of the main routine. This example assumes that interrupt processing is repeated multiple times in a single main routine processing. * Assigns a single byte of RAM to a software watchdog timer (SWDT) and writes the initial value N in the SWDT once at each execution of the main routine. The initial value N should satisfy the following condition: N+1 ( Counts of interrupt processing executed in each main routine) As the main routine execution cycle may change because of an interrupt processing or others, the initial value N should have a margin. * Watches the operation of the interrupt processing routine by comparing the SWDT contents with counts of interrupt processing after the initial value N has been set. * Detects that the interrupt processing routine has failed and determines to branch to the program initialization routine for recovery processing in the following case: If the SWDT contents do not change after interrupt processing. * Decrements the SWDT contents by 1 at each interrupt processing. * Determines that the main routine operates normally when the SWDT contents are reset to the initial value N at almost fixed cycles (at the fixed interrupt processing count). * Detects that the main routine has failed and determines to branch to the program initialization routine for recovery processing in the following case: If the SWDT contents are not initialized to the initial value N but continued to decrement and if they reach 0 or less.
Main routine (SWDT) N CLI Main processing N
Interrupt processing routine (SWDT) (SWDT)--1 Interrupt processing >0 RTI Return Main routine errors
(SWDT) 0? 0
(SWDT) =N? N
Interrupt processing routine errors
Fig. 3.4.10 Watchdog timer by software
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-49
APPENDIX 3804 Group (Spec.H) 3.5 Control registers
3.5 Control registers
Port Pi
b7 b6 b5 b4 b3 b2 b1 b0 Port Pi (i = 0, 1, 2, 3, 4, 5, 6) (Pi: addresses 000016, 000216, 000416, 000616, 000816, 000A16, 000C16)
b
0 1 2 3 4 5 6 7
Name
Port Pi0 Port Pi1 Port Pi2 Port Pi3 Port Pi4 Port Pi5 Port Pi6 Port Pi7
Functions
qIn output mode Write ******** Port latch Read ******** Port latch qIn input mode Write ******** Port latch Read ******** Value of pin
At reset R W
0 0 0 0 0 0 0 0
Fig. 3.5.1 Structure of Port Pi
Port Pi direction register
b7 b6 b5 b4 b3 b2 b1 b0 Port Pi direction register (i = 0, 1, 2, 3, 4, 5, 6) (PiD: addresses 000116, 000316, 000516, 000716, 000916, 000B16, 000D16)
b
Name
Functions
0 : Port Pi0 input mode 1 : Port Pi0 output mode 0 : Port Pi1 input mode 1 : Port Pi1 output mode 0 : Port Pi2 input mode 1 : Port Pi2 output mode 0 : Port Pi3 input mode 1 : Port Pi3 output mode 0 : Port Pi4 input mode 1 : Port Pi4 output mode 0 : Port Pi5 input mode 1 : Port Pi5 output mode 0 : Port Pi6 input mode 1 : Port Pi6 output mode 0 : Port Pi7 input mode 1 : Port Pi7 output mode
At reset R W
0 0 0 0 0 0 0 0
0 Port Pi direction register 1 2 3 4 5 6 7
Fig. 3.5.2 Structure of Port Pi direction register
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-50
APPENDIX 3804 Group (Spec.H) 3.5 Control registers
Timer 12, X count source selection register
b7 b6 b5 b4 b3 b2 b1 b0 Timer 12, X count source selection register (T12XCSS: address 000E16)
b
Name
b3b2b1b0
Functions
0 0 0 0: f(XIN)/2 or f(XCIN)/2 0 0 0 1: f(XIN)/4 or f(XCIN)/4 0 0 1 0: f(XIN)/8 or f(XCIN)/8 0 0 1 1: f(XIN)/16 or f(XCIN)/16 0 1 0 0: f(XIN)/32 or f(XCIN)/32 0 1 0 1: f(XIN)/64 or f(XCIN)/64 0 1 1 0: f(XIN)/128 or f(XCIN)/128 0 1 1 1: f(XIN)/256 or f(XCIN)/256 1 0 0 0: f(XIN)/512 or f(XCIN)/512 1 0 0 1: f(XIN)/1024 or f(XCIN)/1024 1010 to 1111: Not available
b7b6b5b4
At reset R W
1 1 0 0 1 1 0 0
0 Timer 12 count source selection bits 1 2 3 4 Timer X count source selection bits 5 6 7
0 0 0 0: f(XIN)/2 or f(XCIN)/2 0 0 0 1: f(XIN)/4 or f(XCIN)/4 0 0 1 0: f(XIN)/8 or f(XCIN)/8 0 0 1 1: f(XIN)/16 or f(XCIN)/16 0 1 0 0: f(XIN)/32 or f(XCIN)/32 0 1 0 1: f(XIN)/64 or f(XCIN)/64 0 1 1 0: f(XIN)/128 or f(XCIN)/128 0 1 1 1: f(XIN)/256 or f(XCIN)/256 1 0 0 0: f(XIN)/512 or f(XCIN)/512 1 0 0 1: f(XIN)/1024 or f(XCIN)/1024 1 0 1 0: f(XCIN) 1011 to 1111: Not available
Fig. 3.5.3 Structure of Timer 12, X count source selection register
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-51
APPENDIX 3804 Group (Spec.H) 3.5 Control registers
Timer Y, Z count source selection register
b7 b6 b5 b4 b3 b2 b1 b0 Timer Y, Z count source selection register (TYZCSS: address 000F16)
b
Name
b3b2b1b0
Functions
0 0 0 0: f(XIN)/2 or f(XCIN)/2 0 0 0 1: f(XIN)/4 or f(XCIN)/4 0 0 1 0: f(XIN)/8 or f(XCIN)/8 0 0 1 1: f(XIN)/16 or f(XCIN)/16 0 1 0 0: f(XIN)/32 or f(XCIN)/32 0 1 0 1: f(XIN)/64 or f(XCIN)/64 0 1 1 0: f(XIN)/128 or f(XCIN)/128 0 1 1 1: f(XIN)/256 or f(XCIN)/256 1 0 0 0: f(XIN)/512 or f(XCIN)/512 1 0 0 1: f(XIN)/1024 or f(XCIN)/1024 1 0 1 0: f(XCIN) 1011 to 1111: Not available
b7b6b5b4
At reset R W
1 1 0
0 Timer Y count source selection bits 1 2
3 4 Timer Z count source selection bits 5
0
6
7
0 0 0 0: f(XIN)/2 or f(XCIN)/2 0 0 0 1: f(XIN)/4 or f(XCIN)/4 0 0 1 0: f(XIN)/8 or f(XCIN)/8 0 0 1 1: f(XIN)/16 or f(XCIN)/16 0 1 0 0: f(XIN)/32 or f(XCIN)/32 0 1 0 1: f(XIN)/64 or f(XCIN)/64 0 1 1 0: f(XIN)/128 or f(XCIN)/128 0 1 1 1: f(XIN)/256 or f(XCIN)/256 1 0 0 0: f(XIN)/512 or f(XCIN)/512 1 0 0 1: f(XIN)/1024 or f(XCIN)/1024 1 0 1 0: f(XCIN) 1011 to 1111: Not available
1
1
0
0
Fig. 3.5.4 Structure of Timer Y, Z count source selection register
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-52
APPENDIX 3804 Group (Spec.H) 3.5 Control registers
MISRG
b7 b6 b5 b4 b3 b2 b1 b0 MISRG (MISRG: address 001016)
b
Name
Functions
At reset R W
0
0 Oscillatin stabilizing 0: Automatically set (Note 1) time set after STP 1: Autimatically set disabled instrution released bit 1 Middle-speed mode 0: Not set automatically automatic switch set 1: Automatic switching enabled (Notes 2, 3) bit 2 Middle-speed mode 0: 4.5 to 5.5 machine cycles 1: 6.5 to 7.5 machine cycles automatic switch wait time set bit 3 Middle-speed mode 0: Invalid 1: Automatic switch start automatic switch (Note 3) start bit (Depending on program) 4 Nothing is arranged for these bits. These are write disabled bits. When these bits are read 5 out, the contents are "0". 6
0
0
0
0 0 0
0 7 Notes 1: "0116" is set to Timer 1, "FF16" is set to Prescaler 12. 2: During operation in low-speed mode, it is possible automatically to switch to middle-speed mode owing to the rising of SCL/SDA. 3: When automatic switch to middle-speed mode from low-speed mode occurs, the values of CPU mode register (003B16) change.

Fig. 3.5.5 Structure of MISRG
I2C data shift register
b7 b6 b5 b4 b3 b2 b1 b0 I2C data shift register (S0: address 001116)
b
Functions
At reset R W
0 * 8-bit shift register to store receive data and 1 write transmit data. 2 3 4 5 6 7
Undefined Undefined Undefined Undefined Undefined Undefined Undefined Undefined Note: When data is written to I2C data shift register after the MST bit is set to "0" (slave mode), keep the interval for 8 machine cycles or more. Also, when the read-modify-write instructions (SEB, CLB) are used during data transfer, the values may be undefined.
Fig. 3.5.6 Structure of I 2C data shift register
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-53
APPENDIX 3804 Group (Spec.H) 3.5 Control registers
I2C special mode status register
b7 b6 b5 b4 b3 b2 b1 b0 I2C special mode status register (S3: address 001216)
b
Name
Functions
0: Address disagreement 1: Address agreement (Notes 1, 2) 0: Address disagreement 1: Address agreement (Notes 1, 2) 0: Address disagreement 1: Address agreement (Notes 1, 2)
0 Slave address 0 comparison flag (AAS0) 1 Slave address 1 comparison flag (AAS1) 2 Slave address 2 comparison flag (AAS2)
At reset R W 0
0
0
3 Nothing is arranged for this bit. This is a write disabled bit. When this bit is read out, the contents are "0". 4 Nothing is arranged for this bit. This is a write disabled bit. When this bit is read out, the contents are undefined. 5 SCL pin low hold 2 0: SCL pin low hold 1: SCL pin low release flag (PIN2) (Notes 1, 3) Nothing is arranged for this bit. This is a write 6 disabled bit. When this bit is read out, the contents are "0". 7 STOP condition flag (SPCF) 0: No detection 1: Detection (Notes 1, 4)
0

0
1
0

0
Notes 1: These bits and flags can be read out, but cannot be written. 2: These bits can be detected only when the data format selection bit (ALS) of I2C control register is set to "0". 3: This bit is initialized to "1" at reset, when the ACK interrupt control bit is "0", or when writing "1" to the SCL pin low hold 2 flag set bit. 4: This bit is initialized to "0" at reset, when the I2C-BUS interface enable bit (ES0) is "0", or when writing "1" to the STOP condition flag clear bit.
Fig. 3.5.7 Structure of I2C special mode status register
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-54
APPENDIX 3804 Group (Spec.H) 3.5 Control registers
I2C status register
b7 b6 b5 b4 b3 b2 b1 b0 I2C status register (S1: address 001316)
b
Name
Functions
At reset R W
0 Last receive bit (LRB) 1 General call detection flag (AD0) 2 Slave address comparison flag (AAS) 3 Arbitration lost detection flag (AL) 4 SCL pin low hold bit (PIN) 5 Bus busy flag (BB) 6 Communication mode specification bits (TRX, MST) 7
Undefined 0: Last bit = "0" 1: Last bit = "1" (Note 1) 0 0: No general call detected 1: General call detected (Notes 1, 2) 0 0: Address disagreement 1: Address agreement (Notes 1, 2) 0: Not detected 1: Detected (Note 1) 0: SCL pin low hold (Note 3) 1: SCL pin low release 0: Bus free 1: Bus busy
b7 b6
0 1 0 0
0 0 1 1
0: 1: 0: 1:
Slave receive mode Slave transmit mode Master receive mode Master transmit mode
0
Notes 1: These flags and bits are exclusive to input. When writing to these bits, write "0" to these bits. 2: These bits can be detected only when the data format selection bit (ALS) of I2C control register is set to "0". 3: This bit can be set to "1" by program, but cannot be cleared to "0". 4: All bits are changed by hardware. Do not use the readmodify-write instructions (SEB, CLB).
Fig. 3.5.8 Structure of I 2C status register
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-55
APPENDIX 3804 Group (Spec.H) 3.5 Control registers
I2C control register
b7 b6 b5 b4 b3 b2 b1 b0 I2C control register (S1D: address 001416)
b
Name
b2b1b0
Functions
0 0 0: 8 0 0 1: 7 0 1 0: 6 0 1 1: 5 1 0 0: 4 1 0 1: 3 1 1 0: 2 1 1 1: 1
At reset R W
0 0 0 0 0 0
0 Bit counter (Number of transmit/receive 1 bits) (BC0, BC1, BC2) 2
0: Disabled 3 I2C-BUS interface 1: Enabled enable bit (ES0) 0: Addressing format 4 Data format selection bit (ALS) 1: Free data format 5 Addressing format 0: 7-bit addressing format selection bit 1: 10-bit addressing format (10BIT SAD) 6 Nothing is arranged for this bit. This is a write disabled bit. When this bit is read out, the contents are "0". 7 I2C-BUS interface pin 0: SMBUS input input level selection 1: CMOS input bit (TISS)
0
0
Note: Do not use the read-modify-write instruction because some bits change by hardware when the start condition is detected and the byte-transfer is completed.
Fig. 3.5.9 Structure of I 2C control register
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-56
APPENDIX 3804 Group (Spec.H) 3.5 Control registers
I2C clock control register
b7 b6 b5 b4 b3 b2 b1 b0 I2C clock control register (S2: address 001516)
b
Name
Functions
Setting value b4b3b2b1b0 00 to 02 03 04 05 06 Standard High-speed clock mode clock mode Disabled Disabled Disabled 333 (Note 2) 250 100 400 (Note 3) 83.3 166 500/CCR value 1000/CCR value (Note 3) (Note 3) 17.2 34.5 1D 1E 16.6 33.3 1F 16.1 32.3 ( = 4 MHz, Unit: kHz) (Note 1)
At reset R W
0 0 0 0 0 0
0 SCL frequency control bits (CCR0, CCR1, 1 CCR2, CCR3, CCR4) 2 3 4 5 SCL mode specification bit (FAST MODE) 6 ACK bit (ACK BIT) 7 ACK clock bit (ACK)
0: Standard clock mode 1: High-speed clock mode 0: ACK is returned. 1: ACK is not returned. 0: No ACK clock 1: ACK clock
0 0
Notes 1: Duty of SCL clock output is 50 %. The duty becomes 35 to 45 % only when the highspeed clock mode is selected and CCR value = 5 (400 kHz, at = 4 MHz). H duration of the clock fluctuates from --4 to +2 machine cycles in the standard clock mode, and fluctuates from --2 to +2 machine cycles in the high-speed clock mode. In the case of negative fluctuation, the frequency does not increase because L duration is extended instead of H duration reduction. These are values when SCL clock synchronization by the synchronous function is not performed. CCR value is the decimal notation value of the SCL frequency control bits CCR4 to CCR0. 2: Each value of SCL frequency exceeds the limit at = 4 MHz or more. When using these setting value, use of 4 MHz or less. 3: The data formula of SCL frequency is described below: /(8 CCR value) Standard clock mode /(4 CCR value) High-speed clock mode (CCR value 5) /(2 CCR value) High-speed clock mode (CCR value = 5) Do not set 0 to 2 as CCR value regardless of frequency. Set 100 kHz (max.) in the standard clock mode and 400 kHz (max.) in the high-speed clock mode to the SCL frequency by setting the SCL frequency control bits CCR4 to CCR0.
Fig. 3.5.10 Structure of I 2C clock control register
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-57
APPENDIX 3804 Group (Spec.H) 3.5 Control registers
I2C START/STOP condition control register
b7 b6 b5 b4 b3 b2 b1 b0
0
I2C START/STOP condition control register (S2D: address 001616)
b
Name
Functions
SCL release time = (s) (SSC+1) Setup time = (s) (SSC+1)/2 Hold time = (s) (SSC+1)/2
At reset R W
0 1 0 1 1
0 START/STOP condition set bits 1 (SSC0, SSC1, 2 SSC2, SSC3, SSC4) 3 4 5 SCL/SDA interrupt pin polarity selection bit (SIP) 6 SCL/SDA interrupt pin selection bit (SIS) 7 Fix this bit to 0 .
0: Falling edge active 1: Rising edge active 0: SDA valid 1: SCL valid
0
0
0
Note: Fix SSC0 to 0 . Also, do not set SSC4 to SSC0 to odd values or 000002 .
Fig. 3.5.11 Structure of I 2C START/STOP condition control register
I2C special mode control register
b7 b6 b5 b4 b3 b2 b1 b0
0
0
I2C special mode control register (S3D: address 001716)
b
Name
Functions
At reset R W
0 0
0 Fix this bit to 0 . 1 ACK interrupt control 0: At communication completion bit (ACKICON) 1: At falling of ACK clock and communication completion 2 Slave address 0: One-byte slave address control bit (MSLAD) compare mode 1: Three-byte slave address compare mode 3 Nothing is arranged for this bit. This is a write disabled bit. When this bit is read out, the contents are 0 . 4 Fix this bit to 0 . 5 SCL pin low hold 2 Writing 1 to this bit initializes flag set bit (PIN2IN) the SCL pin low hold 2 flag to 1 . (Notes 1, 2) Writing 1 to this bit clears 6 SCL pin low hold set bit (PIN2HD) the SCL pin low hold 2 flag to 0 and holds the SCL pin low. (Notes 1, 2) 7 STOP condition flag Writing 1 to this bit initializes clear bit (SPFCL) the STOP condition flag to 0 . (Note 1)
0
0
0 0
0
0
Notes 1: When 0 is written to these bits, nothing is happened. 2: Do not write 1 to these bits at the same time.
Fig. 3.5.12 Structure of I 2C special mode control register
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-58
APPENDIX 3804 Group (Spec.H) 3.5 Control registers
Transmit/Receive buffer register 1, Transmit/Receive buffer register 3
b7 b6 b5 b4 b3 b2 b1 b0 Transmit/Receive buffer register 1 (TB1/RB1: address 001816) Transmit/Receive buffer register 3 (TB3/RB3: address 003016)
b
0 1 2 3 4 5 6 7
Functions
The transmission data is written to or the receive data is read out from this buffer register. * At write: A data is written to the transmit buffer register. * At read: The contents of the receive buffer register are read out.
At reset R W
Undefined Undefined Undefined Undefined Undefined Undefined Undefined Undefined Note: The contents of transmit buffer register cannot be read out. The data cannot be written to the receive buffer register.
Fig. 3.5.13 Structure of Transmit/Receive buffer register 1, Transmit/Receive buffer register 3
Serial I/O1 status register, Serial I/O3 status register
b7 b6 b5 b4 b3 b2 b1 b0 Serial I/O1 status register (SIO1STS: address 001916) Serial I/O3 status register (SIO3STS: address 003116)
b
Name
Functions
0: Buffer full 1: Buffer empty 0: Buffer empty 1: Buffer full 0: Transmit shift in progress 1: Transmit shift completed
0 Transmit buffer empty flag (TBE) 1 Receive buffer full flag (RBF) 2 Transmit shift register shift completion flag (TSC)
At reset R W 0
0 0

3 Overrun error flag 0: No error (OE) 1: Overrun error 4 Parity error flag 0: No error (PE) 1: Parity error 5 Framing error flag 0: No error (FE) 1: Framing error Summing error flag 0: (OE) U (PE) U (FE) = 0 6 (SE) 1: (OE) U (PE) U (FE) = 1 7 Nothing is arranged for this bit. This bit is a write disabled bit. When this bit is read out, the contents are "1".
0 0 0 0 1

Fig. 3.5.14 Structure of Serial I/O1 status register, Serial I/O3 status register
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-59
APPENDIX 3804 Group (Spec.H) 3.5 Control registers
Serial I/O1 control register
b7 b6 b5 b4 b3 b2 b1 b0 Serial I/O1 control register (SIO1CON: address 001A16)
b
Name
Functions
At reset R W
0 0
0 BRG count source 0: f(XIN) selection bit (CSS) 1: f(XIN)/4 Serial I/O1 When clock synchronous 1 synchronous clock serial I/O is selected, selection bit (SCS) 0: BRG output divided by 4 1: External clock input When UART is selected, 0: BRG output divided by 16 1: External clock input divided by16 2 SRDY1 output enable bit (SRDY) 3 Transmit interrupt source selection bit (TIC) 4 Transmit enable bit (TE) 5 Receive enable bit (RE) 6 Serial I/O1 mode selection bit (SIOM) 7 Serial I/O1 enable bit (SIOE) 0: I/O port (P47) 1: SRDY1 output pin 0: Transmit buffer empty 1: Transmit shift operation completion 0: Transmit disabled 1: Transmit enabled 0: Receive disabled 1: Receive enabled 0: UART 1: Clock synchronous serial I/O 0: Serial I/O1 disabled (P44 to P47: normal I/O pins) 1: Serial I/O1 enabled (P44 to P47: Serial I/O pins)
0 0
0 0 0
0
Fig. 3.5.15 Structure of Serial I/O1 control register
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-60
APPENDIX 3804 Group (Spec.H) 3.5 Control registers
UART1 control register
b7 b6 b5 b4 b3 b2 b1 b0 UART1 control register (UART1CON: address 001B16)
b
Name
Functions
At reset R W
0 0 0 0 0
0 Character length 0: 8 bits selection bit (CHAS) 1: 7 bits 1 Parity enable bit (PARE) 2 Parity selection bit (PARS) 0: Parity checking disabled 1: Parity checking enabled 0: Even parity 1: Odd parity
3 Stop bit length 0: 1 stop bit selection bit (STPS) 1: 2 stop bits 4 P45/TxD1 P-channel 0: CMOS output output disable bit (in output mode) (POFF) 1: N-channel open-drain output (in output mode) 5 Nothing is arranged for these bits. These are 6 write disabled bits. When these bits are read out, the contents are "1". 7
1 1 1

Fig. 3.5.16 Structure of UART1 control register
Baud rate generator i (i = 1, 3)
b7 b6 b5 b4 b3 b2 b1 b0 Baud rate generator i (BRGi (i=1, 3): address 001C16, 002F16)
b
Functions
At reset R W
0 Set a count value of baud rate generator. Undefined 1 Undefined 2 Undefined 3 Undefined 4 Undefined 5 Undefined 6 Undefined 7 Undefined Note: Write to this register while transmit/receive operation is stopped.
Fig. 3.5.17 Structure of Baud rate generator i
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-61
APPENDIX 3804 Group (Spec.H) 3.5 Control registers
Serial I/O2 control register
b7 b6 b5 b4 b3 b2 b1 b0 Serial I/O2 control register (SIO2CON: address 001D16)
b
Name
b2b1b0
Functions
0 0 0: f(XIN)/8 0 0 1: f(XIN)/16 0 1 0: f(XIN)/32 0 1 1: f(XIN)/64 1 1 0: f(XIN)/128 1 1 1: f(XIN)/256 0: I/O port (P51, P52) 1: SOUT2, SCLK2 signal output 0: I/O port (P53) 1: SRDY2 signal output 0: LSB first 1: MSB first 0: External clock 1: Internal clock 0: CMOS output (in output mode) 1: N-channel open-drain output (in output mode)
At reset R W
0 0 0 0 0 0 0
0 Internal synchronous clock 1 selection bits 2 3 Serial I/O2 port selection bit 4 SRDY2 output enable bit 5 Transfer direction selection bit 6 Serial I/O2 synchronous clock selection bit 7 P51/SOUT2 P-channel output disable bit
0
Fig. 3.5.18 Structure of Serial I/O2 control register
Watchdog timer control register
b7 b6 b5 b4 b3 b2 b1 b0 Watchdog timer control register (WDTCON: address 001E16)
b
Name
Functions
0 Watchdog timer H 1 (for read-out of high-order 6 bit) 2 3 4 5 6 STP instruction 0: STP instruction enabled 1: STP instruction disabled disable bit 7 Watchdog timer H 0: Watchdog timer L underflow count source selection 1: f(XIN)/16 or f(XCIN)/16 bit
At reset R W 1 1 1 1 1 1
0 0
Fig. 3.5.19 Structure of Watchdog timer control register
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-62
APPENDIX 3804 Group (Spec.H) 3.5 Control registers
Serial I/O2 register
b7 b6 b5 b4 b3 b2 b1 b0 Serial I/O2 register (SIO2: address 001F16)
b
0 1 2 3 4 5 6 7
Name
Functions
At reset R W
Undefined Undefined Undefined Undefined Undefined Undefined Undefined Undefined
This register becomes shift register. At transmit: Set transmit data to this register. At receive: Received data is stored to this register.
Fig. 3.5.20 Structure of Serial I/O2 register
Prescaler 12, Prescaler X, Prescaler Y
b7 b6 b5 b4 b3 b2 b1 b0 Prescaler 12 (PRE12), Prescaler X (PREX), Prescaler Y (PREY) (addresses 002016, 002416, 002616)
b
Functions
At reset R W
1 1 1 1 1 1 1 1
0 * Set a count value of each prescaler. 1 * The value set in this register is written to both 2 each prescaler and the corresponding 3 prescaler latch at the same time. * When this register is read out, the count value 4 of the corresponding prescaler is read out. 5 6 7
Fig. 3.5.21 Structure of Prescaler 12, Prescaler X, Prescaler Y
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-63
APPENDIX 3804 Group (Spec.H) 3.5 Control registers
Timer 1
b7 b6 b5 b4 b3 b2 b1 b0 Timer 1 (T1: address 002116)
b
Functions
At reset R W
1 0 0 0 0 0 0 0
0 * Set timer 1 count value. 1 * The value set in this register is written to both 2 the timer 1 and the timer 1 latch at the same 3 time. * When the timer 1 is read out, the count value 4 of the timer 1 is read out. 5 6 7
Fig. 3.5.22 Structure of Timer 1
Timer 2, Timer X, Timer Y
b7 b6 b5 b4 b3 b2 b1 b0 Timer 2 (T2), Timer X (TX), Timer Y (TY) (addresses 002216, 002516, 002716)
b
Functions
At reset R W
1 1 1 1 1 1 1 1
0 * Set each timer count value. 1 * The value set in this register is written to both 2 each timer and the corresponding timer latch 3 at the same time. * When each timer is read out, the count value 4 of the corresponding timer is read out. 5 6 7
Fig. 3.5.23 Structure of Timer 2, Timer X, Timer Y
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-64
APPENDIX 3804 Group (Spec.H) 3.5 Control registers
Timer XY mode register
b7 b6 b5 b4 b3 b2 b1 b0 Timer XY mode register (TM: address 002316)
b
Name
b1 b0
Functions
At reset R W
0 0 0 0 0 0 0 0
0 Timer X operating mode bits 1 2 3 4 5 6 7
0 0: Timer mode 0 1: Pulse output mode 1 0: Event counter mode 1 1: Pulse width measurement mode CNTR0 active edge Refer to Table 3.5.1 switch bit Timer X count stop 0: Count start 1: Count stop bit Timer Y operating b5 b4 0 0: Timer mode mode bits 0 1: Pulse output mode 1 0: Event counter mode 1 1: Pulse width measurement mode CNTR1 active edge Refer to Table 3.5.1 switch bit Timer Y count stop 0: Count start 1: Count stop bit
Fig. 3.5.24 Structure of Timer XY mode register Table 3.5.1 CNTR0/CNTR1 active edge switch bit function Timer X/Timer Y operation modes CNTR0/CNTR1 active edge switch bit (bits 2 and 6 of address 002316) contents Timer mode "0" CNTR0/CNTR1 interrupt request occurrence: Falling edge ; No influence to timer count "1" CNTR0/CNTR1 interrupt request occurrence: Rising edge Pulse output mode ; No influence to timer count "0" Pulse output start: Beginning at "H" level CNTR0/CNTR1 interrupt request occurrence: Falling edge "1" Pulse output start: Beginning at "L" level CNTR0/CNTR1 interrupt request occurrence: Rising edge Event counter mode "0" Timer X/Timer Y: Rising edge count CNTR0/CNTR1 interrupt request occurrence: Falling edge "1" Timer X/Timer Y: Falling edge count CNTR0/CNTR1 interrupt request occurrence: Rising edge Pulse width measurement mode "0" Timer X/Timer Y: "H" level width measurement CNTR0/CNTR1 interrupt request occurrence: Falling edge "1" Timer X/Timer Y: "L" level width measurement CNTR0/CNTR1 interrupt request occurrence: Rising edge
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-65
APPENDIX 3804 Group (Spec.H) 3.5 Control registers
Timer Z low-order, Timer Z high-order
b7 b6 b5 b4 b3 b2 b1 b0 Timer Z low-order (TZL), Timer Z high-order (TZH) (addresses 002816, 002916)
b
Functions
At reset R W
1 1 1 1 1 1 1 1
0 * Set each timer count value. [At write] 1 * Depending on the write control bit (bit 3 of TZM), the value set to this register is written to 2 each timer and the corresponding timer latch at the same time, or is written only to the latch. 3 [At read] 4 * The corresponding timer count value is read out by reading this register. 5 * Read both registers in order of TZH and TZL following. 6 * Write both registers in order of TZL and TZH 7 following.
Fig. 3.5.25 Structure of Timer Z low-order, Timer Z high-order
Timer Z mode register
b7 b6 b5 b4 b3 b2 b1 b0 Timer Z mode register (TZM: address 002A16)
b
Name
b2b1b0
Functions
0 0 0: Timer/Event counter mode 0 0 1: Pulse output mode 0 1 0: Pulse period measurement mode 0 1 1: Pulse width measurement mode 1 0 0: Programmable waveform generating mode 1 0 1: Programmable one-shot generating mode 1 1 0: Not available 1 1 1: Not available
At reset R W
0
0 Timer Z operating mode bits 1
0
2
0
3 Timer Z write control 0: Writing data to both latch and timer simultaneousuly bit 1: Writing data only to latch 0: "L" output 4 Output level latch 1: "H" output 5 CNTR2 active edge Refer to Table 3.5.2. switch bit 6 Timer Z count stop 0: Count start 1: Count stop bit 7 Timer/Event counter 0: Timer mode mode switch bit (Note) 1: Event counter mode
0
0 0 0 0
Note: When selecting the modes except the timer/event counter mode, set "0" to this bit.
Fig. 3.5.26 Structure of Timer Z mode register
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-66
APPENDIX 3804 Group (Spec.H) 3.5 Control registers
Table 3.5.2 CNTR2 active edge switch bit function Timer Z operation modes Timer mode CNTR2 active edge switch bit (bit 5 of address 002A16) contents "0" CNTR2 interrupt request occurrence: Falling edge ; No influence to timer count "1" CNTR2 interrupt request occurrence: Rising edge ; No influence to timer count Event counter mode "0" Timer Z: Rising edge count CNTR2 interrupt request occurrence: Falling edge "1" Timer Z: Falling edge count CNTR2 interrupt request occurrence: Rising edge Pulse output mode "0" Pulse output start: Beginning at "H" level CNTR2 interrupt request occurrence: Falling edge "1" Pulse output start: Beginning at "L" level CNTR2 interrupt request occurrence: Rising edge Pulse period measurement mode "0" Timer Z: Period from falling edge to the next falling edge measurement CNTR2 interrupt request occurrence: Falling edge "1" Timer Z: Period from rising edge to the next rising edge measurement Pulse width measurement mode CNTR2 interrupt request occurrence: Rising edge "0" Timer Z: "H" level width measurement CNTR2 interrupt request occurrence: Falling edge "1" Timer Z: "L" level width measurement CNTR2 interrupt request occurrence: Rising edge Programmable one-shot generating "0" Timer Z: after start outputting "L", "H" one-shot pulse generated mode CNTR2 interrupt request occurrence: Falling edge "1" Timer Z: after start outputting "H", "L" one-shot pulse generated CNTR2 interrupt request occurrence: Rising edge
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-67
APPENDIX 3804 Group (Spec.H) 3.5 Control registers
PWM control register
b7 b6 b5 b4 b3 b2 b1 b0 PWM control register (PWMCON: address 002B16)
b
0 1 2 3 4 5 6 7
Name
Functions
At reset R W
0 0 0 0 0 0 0 0
PWM function 0 : PWM disabled enable bit 1 : PWM enabled Count source 0 : f(XIN) selection bit 1 : f(XIN)/2 Nothing is arranged for these bits. These are write disabled bits. When these bits are read out, the contents are "0".

Fig. 3.5.27 Structure of PWM control register
PWM prescaler
b7 b6 b5 b4 b3 b2 b1 b0 PWM prescaler (PREPWM: address 002C16)
b
Functions
At reset R W
Undefined Undefined Undefined Undefined Undefined Undefined Undefined Undefined
0 *Set the PWM period. 1 *The value set in this register is written to both PWM prescaler pre-latch and PWM prescaler 2 latch at the same time. 3 * When data is written to this register during PWM output, the pulse corresponding to 4 changed value is output at the next period. 5 * When this register is read out, the count value of the PWM prescaler latch is read out. 6 7
Fig. 3.5.28 Structure of PWM prescaler
PWM register
b7 b6 b5 b4 b3 b2 b1 b0 PWM register (PWM: address 002D16)
b
Functions
At reset R W
Undefined Undefined Undefined Undefined Undefined Undefined Undefined Undefined
0 * Set the PWM "H" level output interval. 1 * The value set in this register is written to both PWM register pre-latch and PWM register 2 latch at the same time. 3 * When data is written to this register during PWM output, the pulse corresponding to 4 changed value is output at the next period. 5 * When this register is read out, the contents of the PWM register latch is read out. 6 7
Fig. 3.5.29 Structure of PWM register
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-68
APPENDIX 3804 Group (Spec.H) 3.5 Control registers
Serial I/O3 control register
b7 b6 b5 b4 b3 b2 b1 b0 Serial I/O3 control register (SIO3CON: address 003216)
b
Name
Functions
At reset R W
0 0
0 BRG count source 0: f(XIN) selection bit (CSS) 1: f(XIN)/4 When clock synchronous 1 Serial I/O3 synchronous clock serial I/O is selected, selection bit (SCS) 0: BRG output divided by 4 1: External clock input When UART is selected, 0: BRG output divided by 16 1: External clock input divided by16 2 SRDY3 output enable bit (SRDY) 3 Transmit interrupt source selection bit (TIC) 4 Transmit enable bit (TE) 5 Receive enable bit (RE) 6 Serial I/O3 mode selection bit (SIOM) 7 Serial I/O3 enable bit (SIOE) 0: I/O port (P37) 1: SRDY3 output pin 0: Transmit buffer empty 1: Transmit shift operation completion 0: Transmit disabled 1: Transmit enabled 0: Receive disabled 1: Receive enabled 0: UART 1: Clock synchronous serial I/O 0: Serial I/O3 disabled (P34 to P37: normal I/O pins) 1: Serial I/O3 disabled (P34 to P37: Serial I/O pins)
0 0
0 0 0
0
Fig. 3.5.30 Structure of Serial I/O3 control register
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-69
APPENDIX 3804 Group (Spec.H) 3.5 Control registers
UART3 control register
b7 b6 b5 b4 b3 b2 b1 b0 UART3 control register (UART3CON: address 003316)
b
Name
Functions
At reset R W
0 0 0 0 0
0 Character length 0: 8 bits selection bit (CHAS) 1: 7 bits 1 Parity enable bit (PARE) 2 Parity selection bit (PARS) 0: Parity checking disabled 1: Parity checking enabled 0: Even parity 1: Odd parity
3 Stop bit length 0: 1 stop bit selection bit (STPS) 1: 2 stop bits 4 P35/TxD3 P-channel 0: CMOS output output disable bit (in output mode) (POFF) 1: N-channel open-drain output (in output mode) 5 Nothing is arranged for these bits. These are 6 write disabled bits. When these bits are read out, the contents are "1". 7
1 1 1

Fig. 3.5.31 Structure of UART3 control register
AD/DA control register
b7 b6 b5 b4 b3 b2 b1 b0 AD/DA control register (ADCON: address 003416)
b
Name
b2 b1 b0
Functions
0 0 0: P60/AN0 or P00/AN8 0 0 1: P61/AN1 or P01/AN9 0 1 0: P62/AN2 or P02/AN10 0 1 1: P63/AN3 or P03/AN11 1 0 0: P64/AN4 or P04/AN12 1 0 1: P65/AN5 or P05/AN13 1 1 0: P66/AN6 or P06/AN14 1 1 1: P67/AN7 or P07/AN15
At reset R W
0
0 Analog input pin selection bits 1 1
0
2
0
0: Conversion in progress 3 AD conversion 1: Conversion completed completion bit 4 Analog input pin 0: AN0 to AN7 side 1: AN8 to AN15 side selection bit 2 5 Nothing is arranged for this bit. This is a write disabled bit. When this bit is read out, the contents are "0". 6 DA1 output enable 0: DA1 output disabled 1: DA1 output enabled bit 7 DA2 output enable 0: DA2 output disabled 1: DA2 output enabled bit
1 0 0
0 0
Fig. 3.5.32 Structure of AD/DA control register
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-70
APPENDIX 3804 Group (Spec.H) 3.5 Control registers
AD conversion register 1
b7 b6 b5 b4 b3 b2 b1 b0 AD conversion register 1 (AD1: address 003516)
b
0 1 2 3 4 5 6 7
Functions
At reset R W
This is A/D conversion result stored bits. This is Undefined Undefined read exclusive register. 0 Undefined 0 8-bit read b7 b0 Undefined 0 b9 b8 b7 b6 b5 b4 b3 b2 Undefined 0 Undefined 0 10-bit read b7 b0 Undefined 0 b7 b6 b5 b4 b3 b2 b1 b0 Undefined
Fig. 3.5.33 Structure of AD conversion register 1
DAi conversion register
b7 b6 b5 b4 b3 b2 b1 b0 DAi conversion register (i = 1, 2) (DAi: addresses 003616, 003716)
b
Functions
At reset R W
0 0 0 0 0 0 0 0
0 This is D/A output value stored bits. This is write 1 exclusive register. 2 3 4 5 6 7
Fig. 3.5.34 Structure of DAi conversion register (i = 1, 2)
AD conversion register 2
b7 b6 b5 b4 b3 b2 b1 b0 AD conversion register 2 (AD2: address 003816)
b
Functions
At reset R W
0 This is A/D conversion result stored bits. This is Undefined read exclusive register. 10-bit read b0 b7 Undefined 1 0 b9 b8 2 3 4 5 6 7 Nothing is arranged for these bits. These are write disabled bits. When these bits are read out, the contents are "0". 0 0 0 0 0 0
Conversion mode selection bit
0: 10-bit A/D mode 1: 8-bit A/D mode
Fig. 3.5.35 Structure of AD conversion register 2
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-71
APPENDIX 3804 Group (Spec.H) 3.5 Control registers
Interrupt source selection register
b7 b6 b5 b4 b3 b2 b1 b0 Interrupt source selection register (INTSEL: address 003916)
b
Name
Functions
0: INT0 interrupt 1: Timer Z interrupt 0: Serial I/O2 interrupt 1: Timer Z interrupt 0: Serial I/O1 transmit interrupt 1: SCL, SDA interrupt 0: CNTR0 interrupt 1: SCL, SDA interrupt 0: INT4 interrupt 1: CNTR2 interrupt 0: INT2 interrupt 1: I2C interrupt 0: CNTR1 interrupt 1: Serial I/O3 receive interrupt 0: A/D converter interrupt 1: Serial I/O3 transmit interrupt
At reset R W
0
0 INT0/Timer Z interrupt source selection bit (*1) 1 Serial I/O2/Timer Z interrupt source selection bit (*1) 2 Serial I/O1 transmit/ SCL, SDA interrupt source selection bit (*2) 3 CNTR0/SCL, SDA interrupt source selection bit (*2) 4 INT4/CNTR2 interrupt source selection bit 5 INT2/I2C interrupt source selection bit 6 CNTR1/Serial I/O3 receive interrupt source selection bit 7 AD converter/Serial I/O3 transmit interrupt source selection bit
0
0
0
0
0 0
0
*1: Do not write 1 to these bits simultaneously. *2: Do not write 1 to these bits simultaneously.
Fig. 3.5.36 Structure of Interrupt source selection register
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-72
APPENDIX 3804 Group (Spec.H) 3.5 Control registers
Interrupt edge selection register
b7 b6 b5 b4 b3 b2 b1 b0 Interrupt edge selection register (INTEDGE: address 003A16)
b
Name
Functions
At reset R W
0 0 0
0: Falling edge active 0 INT0 active edge 1: Rising edge active selection bit 0: Falling edge active 1 INT1 active edge 1: Rising edge active selection bit 2 Nothing is arranged for this bit. This is a write disabled bit. When this bit is read out, the contents are "0". 3 INT2 active edge 0: Falling edge active selection bit 1: Rising edge active 4 INT3 active edge 0: Falling edge active selection bit 1: Rising edge active 0: Falling edge active 5 INT4 active edge selection bit 1: Rising edge active 6 INT0, INT4 interrupt 0: INT00, INT40 interrupt switch bit 1: INT01, INT41 interrupt 7 Nothing is arranged for this bit. This is a write disabled bit. When this bit is read out, the contents are "0".
0 0 0 0 0
Fig. 3.5.37 Structure of Interrupt edge selection register
CPU mode register
b7 b6 b5 b4 b3 b2 b1 b0
1
CPU mode register (CPUM: address 003B16)
b
Name
b1 b0
Functions
00 : Single-chip mode 01 : 10 : Not available 11 : 0 : 0 page 1 : 1 page 0: I/O port function (stop oscillating) 1: XCIN-XCOUT oscillation function 0: Oscillating 1: Stopped 0 0: =f(XIN)/2 (high-speed mode) 0 1: =f(XIN)/8 (middle-speed mode) 1 0: =f(XCIN)/2 (low-speed mode) 1 1: not available
b7 b6
At reset R W
0 0 0 1 0
0 Processor mode bits 1 2 Stack page selection bit 3 Fix this bit to "1". 4 Port Xc switch bit
5 Main clock (XINXOUT) stop bit 6 Main clock division ratio selection bits
0 1
7
0
Fig. 3.5.38 Structure of CPU mode register
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-73
APPENDIX 3804 Group (Spec.H) 3.5 Control registers
Interrupt request register 1
b7 b6 b5 b4 b3 b2 b1 b0 Interrupt request register 1 (IREQ1 : address 003C16)
b
Name
Functions
At reset R W
0 0 0 0
0 INT0/Timer Z 0 : No interrupt request issued interrupt request bit 1 : Interrupt request issued 1 INT1 interrupt request bit
0 : No interrupt request issued
1 : Interrupt request issued
2 Serial I/O1 receive 0 : No interrupt request issued interrupt request bit 1 : Interrupt request issued
0 : No interrupt request issued 3 Serial I/O1 transmit/SCL, SDA 1 : Interrupt request issued interrupt request bit
4 Timer X interrupt request bit 5 Timer Y interrupt request bit 6 Timer 1 interrupt request bit
0 : No interrupt request issued
0 0 0 0

1 : Interrupt request issued
0 : No interrupt request issued
1 : Interrupt request issued
0 : No interrupt request issued
1 : Interrupt request issued
7 Timer 2 interrupt 0 : No interrupt request issued request bit 1 : Interrupt request issued : 0 can be set by software, but 1 cannot be set.
Fig. 3.5.39 Structure of Interrupt request register 1
Interrupt request register 2
b7 b6 b5 b4 b3 b2 b1 b0 Interrupt request register 2 (IREQ2 : address 003D16)
b
Name
Functions
0 : No interrupt request issued 1 : Interrupt request issued 0 : No interrupt request issued 1 : Interrupt request issued 0 : No interrupt request issued 1 : Interrupt request issued 0 : No interrupt request issued 1 : Interrupt request issued 0 : No interrupt request issued 1 : Interrupt request issued 0 : No interrupt request issued 1 : Interrupt request issued 0 : No interrupt request issued 1 : Interrupt request issued
At reset R W
0 0
0 CNTR0/SCL, SDA interrupt request bit 1 CNTR1/Serial I/O3 receive interrupt request bit 2 Serial I/O2/Timer Z interrupt request bit 3 INT2/I2C interrupt request bit 4 INT3 interrupt request bit 5 INT4/CNTR2 interrupt request bit 6 AD converter/Serial I/O3 transmit interrupt request bit
0 0 0 0 0

7 Nothing is arranged for this bit. This is a write disabled bit. When this bit is read out, the contents are 0 . : 0 can be set by software, but 1 cannot be set.
0
Fig. 3.5.40 Structure of Interrupt request register 2
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-74
APPENDIX 3804 Group (Spec.H) 3.5 Control registers
Interrupt control register 1
b7 b6 b5 b4 b3 b2 b1 b0 Interrupt control register 1 (ICON1 : address 003E16)
b
Name
Functions
0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled
At reset R W
0 0 0 0
0 INT0/Timer Z interrupt enable bit 1 INT1 interrupt enable bit 2 Serial I/O1 receive interrupt enable bit 3 Serial I/O1 transmit/SCL, SDA interrupt enable bit 4 Timer X interrupt enable bit 5 Timer Y interrupt enable bit 6 Timer 1 interrupt enable bit Timer 2 interrupt 7 enable bit
0 0 0 0
Fig. 3.5.41 Structure of Interrupt control register 1
Interrupt control register 2
b7 b6 b5 b4 b3 b2 b1 b0
0
Interrupt control register 2 (ICON2 : address 003F16)
b
Name
Functions
0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled
At reset R W
0 0
0 CNTR0 interrupt enable bit CNTR1/ Serial I/O3 1 receive interrupt enable bit 2 Serial I/O2/ Timer Z interrupt enable bit 3 INT2 interrupt enable bit 4 INT3 interrupt enable bit 5 INT4/CNTR2 interrupt enable bit AD converter/Serial 6 I/O3 transmit interrupt enable bit 7 Fix this bit to "0".
0 0 0 0 0
0
Fig. 3.5.42 Structure of Interrupt control register 2
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-75
APPENDIX 3804 Group (Spec.H) 3.5 Control registers
Flash memory control register 0
b7 b6 b5 b4 b3 b2 b1 b0 Flash memory control register 0 (FMCR0 : address 0FE016)
b
Name
Functions
0 : Busy (being automatic written or automatic erased) 1 : Ready
At reset R W
1
0 RY/BY status flag
1 CPU rewrite mode select bit (Note 1)
2
3 4 5 6 7
0 : CPU rewrite mode invalid (software commandes invalid) 1 : CPU rewrite mode valid (Software commands acceptable) 8 KB user block E/W 0: E/W disabled enable bit (Notes 1, 1: E/W enabled 2) Flash memory reset 0: Normal operation bit (Note 3) 1: Reset Not used (Do not write "1" to this bit.) User ROM area 0: User ROM area is accessed select bit 1: Boot ROM area is accessed Program status flag 0: Pass 1: Error Erase status flag 0: Pass 1: Error
0
0
0 0 0 0 0
Notes 1: For this bit to be set to "1", the user needs to write a "0" and then a "1" to it in succession. For this bit to be set to "0", write "0" only to this bit. 2: This bit can be written only when the CPU rewrite mode select bit is "1". 3: Effective only when the CPU rewrite mode select bit = "1". Fix this bit to "0" when the CPU rewrite mode select bit is "0". 4: When setting this bit to "1" (when the control circuit of flash memory is reset), the flash memory cannot be accessed for 10 s. 5: Write to this bit from program on RAM.
Fig. 3.5.43 Structure of Flash memory control register 0
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-76
APPENDIX 3804 Group (Spec.H) 3.5 Control registers
Flash memory control register 1
b7 b6 b5 b4 b3 b2 b1 b0 Flash memory control register 1 (FMCR1 : address 0FE116)
b
Name
Functions
At reset R W
0 0
0 : Suspend invalid 0 Erase suspend enable bit (Note 1) 1 : Suspend valid 1 Erase suspend 0 : Erase restart (no request issued) request bit (Note 2) 1 : Suspend request (request issued) 2 Nothing is arranged for these bits. If writing to 3 these bits, write "0". The contents are undefined 4 at reading. 5 0 : Erase active 6 Erase suspend flag 1 : Erase inactive (Erase suspend mode) 7 Nothing is arranged for these bits. If writing to these bits, write "0". The contents are undefined at reading.
0 0 0 0 1
0
Notes 1: For this bit to be set to "1", the user needs to write a "0" and then a "1" to it in succession. 2: Only when the erase suspend bit is "1", this bit is valid.
Fig. 3.5.44 Structure of Flash memory control register 1
Flash memory control register 2
b7 b6 b5 b4 b3 b2 b1 b0 Flash memory control register 2 (FMCR2 : address 0FE216)
b
0 1 2 3 4
Name
Functions
At reset R W
1 0 1 0 0
Nothing is arranged for these bits. If writing to these bits, write "0". The contents are undefined at reading.
All user block E/W 0 : E/W disabled enable bit (Notes 1, 2) 1 : E/W enabled 0 5 Nothing is arranged for these bits. If writing to 6 these bits, write "0". The contents are undefined 1 7 at reading. 0 Notes 1: For this bit to be set to "1", the user needs to write a "0" and then a "1" to it in succession. 2: Effective only when the CPU rewrite mode select bit = "1".
Fig. 3.5.45 Structure of Flash memory control register 2
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-77
APPENDIX 3804 Group (Spec.H) 3.5 Control registers
Port Pi pull-up control register (i = 0 to 2, 4 to 6)
b7 b6 b5 b4 b3 b2 b1 b0 Port Pi pull-up control register (i = 0 to 2, 4 to 6) (PULLi: addresses 0FF016, 0FF116, 0FF216, 0FF416, 0FF516, 0FF616)
b
Name
Functions
0: No pull-up 1: Pull-up 0: No pull-up 1: Pull-up 0: No pull-up 1: Pull-up 0: No pull-up 1: Pull-up 0: No pull-up 1: Pull-up 0: No pull-up 1: Pull-up 0: No pull-up 1: Pull-up 0: No pull-up 1: Pull-up
At reset R W
0 0 0 0 0 0 0 0
0 Port Pi0 pull-up control bit 1 Port Pi1 pull-up control bit 2 Port Pi2 pull-up control bit 3 Port Pi3 pull-up control bit 4 Port Pi4 pull-up control bit 5 Port Pi5 pull-up control bit 6 Port Pi6 pull-up control bit 7 Port Pi7 pull-up control bit
Fig. 3.5.46 Structure of Port Pi pull-up control register (i = 0 to 2, 4 to 6)
Port P3 pull-up control register
b7 b6 b5 b4 b3 b2 b1 b0 Port P3 pull-up control register (PULL3: address 0FF316)
b
Name
Functions
At reset R W
0 0 0 0 0 0 0 0 0
0: No pull-up 0 Port P30 pull-up control bit 1: Pull-up 0: No pull-up 1 Port P31 pull-up control bit 1: Pull-up 2 Nothing is arranged for these bits. These are write disabled bits. When these bits are read 3 out, the contents are "0". 0: No pull-up 4 Port P34 pull-up control bit 1: Pull-up 5 Port P35 pull-up 0: No pull-up control bit 1: Pull-up 0: No pull-up 6 Port P36 pull-up control bit 1: Pull-up 7 Port P37 pull-up 0: No pull-up control bit 1: Pull-up
Fig. 3.5.47 Structure of Port P3 pull-up control register
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-78
APPENDIX 3804 Group (Spec.H) 3.5 Control registers
I2C slave address register i (i = 0 to 2)
b7 b6 b5 b4 b3 b2 b1 b0 I2C slave address register i (i = 0 to 2) (S0D0, S0D1, S0D2: addresses 0FF716, 0FF816, 0FF916)
b
Name
Functions
0: Write bit 1: Read bit
At reset R W
0
0 Read/Write bit (RWB)
1 Slave address 0 The contents of these bits 2 (SAD0, SAD1, SAD2, are compared with the 0 3 SAD3, SAD4, SAD5, address data transmitted 0 from master. 4 SAD6) 0 5 0 6 0 7 0 Note: When the read-modify-write instructions (SEB, CLB) are used at detection of stop condition, the values may be undefined.
Fig. 3.5.48 Structure of I 2C slave address register i (i = 0 to 2)
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-79
APPENDIX 3804 Group (Spec.H) 3.6 Package outline
3.6 Package outline
64P6N-A
EIAJ Package Code QFP64-P-1414-0.80 HD D b2
64 49
Plastic 64pin 1414mm body QFP
JEDEC Code - Weight(g) 1.11 Lead Material Alloy 42 e MD
1
48
I2 Recommended Mount Pad Symbol A A1 A2 b c D E e HD HE L L1 y b2 I2 MD ME Dimension in Millimeters Min Nom Max - - 3.05 0.1 0.2 0 - - 2.8 0.3 0.35 0.45 0.13 0.15 0.2 13.8 14.0 14.2 13.8 14.0 14.2 - 0.8 - 16.5 16.8 17.1 16.5 16.8 17.1 0.4 0.6 0.8 1.4 - - 0.1 - - 0 10 - - - 0.5 1.3 - - - - 14.6 - - 14.6 HE E
16
33
17
32
A
L1
A2
F A1 e y b L Detail F
64P4B
EIAJ Package Code SDIP64-P-750-1.78 JEDEC Code - Weight(g) 7.9 Lead Material Alloy 42/Cu Alloy
c
Plastic 64pin 750mil SDIP
64
33
1
32
Symbol
D A2
e SEATING PLANE
b1
b
b2
A A1 A2 b b1 b2 c D E e e1 L
Dimension in Millimeters Min Nom Max - - 5.08 0.38 - - - 3.8 - 0.4 0.5 0.59 0.9 1.0 1.3 0.65 0.75 1.05 0.2 0.25 0.32 56.2 56.4 56.6 16.85 17.0 17.15 - 1.778 - - 19.05 - 2.8 - - 0 - 15
L
A
A1
e1
E
c
ME
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-80
APPENDIX 3804 Group (Spec.H) 3.6 Package outline
Plastic 64pin 1010mm body LQFP
e JEDEC Code -- Weight(g) Lead Material Cu Alloy MD
64P6Q-A
EIAJ Package Code LQFP64-P-1010-0.5
HD D
48 33
49
32
b2
I2 Recommended Mount Pad Symbol A A1 A2 b c D E e HD HE L L1 Lp
A3 A3
64
17
1
16
A e F L1
A1
y
b
x y b2 I2 MD ME
x
M
L Detail F
Lp
Dimension in Millimeters Min Nom Max -- -- 1.7 0.1 0.2 0 -- -- 1.4 0.13 0.18 0.28 0.105 0.125 0.175 9.9 10.0 10.1 9.9 10.0 10.1 -- 0.5 -- 11.8 12.0 12.2 11.8 12.0 12.2 0.3 0.5 0.7 1.0 -- -- 0.75 0.6 0.45 -- 0.25 -- 0.08 -- -- 0.1 -- -- 0 10 -- 0.225 -- -- -- -- 1.0 -- -- 10.4 -- -- 10.4
HE
E
A2
64P6U-A
EIAJ Package Code LQFP64-P-1414-0.8 JEDEC Code -- HD D
48 33
c
Plastic 64pin 1414mm body LQFP
Weight(g) Lead Material Cu Alloy e MD
l2
49 32
Recommended Mount Pad Symbol A A1 A2 b c D E e HD HE L L1 Lp
A3
64
17
1
16
A F L1 A2
e
A3
Lp
c
y
b
x
M
A1
L
x y b2 I2 MD ME
Detail F
Dimension in Millimeters Min Nom Max -- -- 1.7 0.1 0.2 0 1.4 -- -- 0.32 0.37 0.45 0.105 0.125 0.175 13.9 14.1 14.0 13.9 14.1 14.0 0.8 -- -- 16.0 15.8 16.2 15.8 16.2 16.0 0.3 0.5 0.7 1.0 -- -- 0.75 0.6 0.45 -- 0.25 -- -- -- 0.2 0.1 -- -- 0 8 -- 0.5 -- -- -- -- 0.95 -- 14.4 -- -- -- 14.4
HE
E
ME
b2
ME
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-81
APPENDIX 3804 Group (Spec.H) 3.7 Machine instructions
3.7 Machine instructions
Addressing mode Symbol Function Details IMP OP n ADC (Note 1) (Note 5) When T = 0 AA+M+C When T = 1 M(X) M(X) + M + C When T = 0, this instruction adds the contents M, C, and A; and stores the results in A and C. When T = 1, this instruction adds the contents of M(X), M and C; and stores the results in M(X) and C. When T=1, the contents of A remain unchanged, but the contents of status flags are changed. M(X) represents the contents of memory where is indicated by X. When T = 0, this instruction transfers the contents of A and M to the ALU which performs a bit-wise AND operation and stores the result back in A. When T = 1, this instruction transfers the contents M(X) and M to the ALU which performs a bit-wise AND operation and stores the results back in M(X). When T = 1, the contents of A remain unchanged, but status flags are changed. M(X) represents the contents of memory where is indicated by X. This instruction shifts the content of A or M by one bit to the left, with bit 0 always being set to 0 and bit 7 of A or M always being contained in C. This instruction tests the designated bit i of M or A and takes a branch if the bit is 0. The branch address is specified by a relative address. If the bit is 1, next instruction is executed. This instruction tests the designated bit i of the M or A and takes a branch if the bit is 1. The branch address is specified by a relative address. If the bit is 0, next instruction is executed. This instruction takes a branch to the appointed address if C is 0. The branch address is specified by a relative address. If C is 1, the next instruction is executed. This instruction takes a branch to the appointed address if C is 1. The branch address is specified by a relative address. If C is 0, the next instruction is executed. This instruction takes a branch to the appointed address when Z is 1. The branch address is specified by a relative address. If Z is 0, the next instruction is executed. This instruction takes a bit-wise logical AND of A and M contents; however, the contents of A and M are not modified. The contents of N, V, Z are changed, but the contents of A, M remain unchanged. This instruction takes a branch to the appointed address when N is 1. The branch address is specified by a relative address. If N is 0, the next instruction is executed. This instruction takes a branch to the appointed address if Z is 0. The branch address is specified by a relative address. If Z is 1, the next instruction is executed. 24 3 2 IMM # OP n 69 2 A # OP n 2 BIT, A BIT, A, R # OP n ZP BIT, ZP BIT, ZP, R # OP n 2 #
# OP n 65 3
ASL C
7
0
0
BBC (Note 4)
Ai or Mi = 0?
BBS (Note 4)
Ai or Mi = 1?
BCC (Note 4)
C = 0?
BCS (Note 4)
C = 1?
BEQ (Note 4)
Z = 1?
BIT
A
M
BMI (Note 4)
N = 1?
BNE (Note 4)
Z = 0?
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
V
When T = 1 M(X) M(X)
V
AND (Note 1)
When T = 0 AA M M
29 2
2
25 3
2
0A 2
1
06 5
2
13 4 + 20i
2
17 5 + 20i
3
03 4 + 20i
2
07 5 + 20i
3
V
3-82
APPENDIX 3804 Group (Spec.H) 3.7 Machine instructions
Addressing mode ZP, X OP n 75 4 ZP, Y # OP n 2 ABS # OP n 6D 4 ABS, X # OP n 3 7D 5 ABS, Y IND ZP, IND # OP n IND, X IND, Y REL SP # OP n # 7
Processor status register 6 V V 5 T * 4 B * 3 D * 2 I * 1 Z Z 0 C C
# OP n 3 79 5
# OP n 3
# OP n 61 6
# OP n 2 71 6
# OP n 2
N N
35 4
2
2D 4
3 3D 5
3 39 5
3
21 6
2 31 6
2
N
*
*
*
*
*
Z
*
16 6
2
0E 6
3 1E 7
3
N
*
*
*
*
*
Z
C
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
90 2
2
*
*
*
*
*
*
*
*
B0 2
2
*
*
*
*
*
*
*
*
F0 2
2
*
*
*
*
*
*
*
*
2C 4
3
M7 M6 *
*
*
*
Z
*
30 2
2
*
*
*
*
*
*
*
*
D0 2
2
*
*
*
*
*
*
*
*
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-83
APPENDIX 3804 Group (Spec.H) 3.7 Machine instructions
Addressing mode Symbol Function Details IMP OP n BPL (Note 4) N = 0? This instruction takes a branch to the appointed address if N is 0. The branch address is specified by a relative address. If N is 1, the next instruction is executed. This instruction branches to the appointed address. The branch address is specified by a relative address. When the BRK instruction is executed, the CPU pushes the current PC contents onto the stack. The BADRS designated in the interrupt vector table is stored into the PC. 00 7 1 IMM # OP n A # OP n BIT, A # OP n ZP # OP n BIT, ZP # OP n #
BRA
PC PC offset
BRK
B1 (PC) (PC) + 2 M(S) PCH SS-1 M(S) PCL SS-1 M(S) PS SS-1 I 1 PCL ADL PCH ADH V = 0?
BVC (Note 4)
This instruction takes a branch to the appointed address if V is 0. The branch address is specified by a relative address. If V is 1, the next instruction is executed. This instruction takes a branch to the appointed address when V is 1. The branch address is specified by a relative address. When V is 0, the next instruction is executed. This instruction clears the designated bit i of A or M. This instruction clears C. 18 2 1 1B 2 + 20i 1 1F 5 + 20i 2
BVS (Note 4)
V = 1?
CLB
Ai or Mi 0 C0 D0 I0 T0 V0 When T = 0 A-M When T = 1 M(X) - M
CLC
CLD
This instruction clears D.
D8 2
1
CLI
This instruction clears I.
58 2
1
CLT
This instruction clears T.
12 2
1
CLV
This instruction clears V.
B8 2
1
CMP (Note 3)
When T = 0, this instruction subtracts the contents of M from the contents of A. The result is not stored and the contents of A or M are not modified. When T = 1, the CMP subtracts the contents of M from the contents of M(X). The result is not stored and the contents of X, M, and A are not modified. M(X) represents the contents of memory where is indicated by X. This instruction takes the one's complement of the contents of M and stores the result in M. This instruction subtracts the contents of M from the contents of X. The result is not stored and the contents of X and M are not modified. This instruction subtracts the contents of M from the contents of Y. The result is not stored and the contents of Y and M are not modified. This instruction subtracts 1 from the contents of A or M.
C9 2
2
C5 3
2
COM
MM
__
44 5
2
CPX
X-M
E0 2
2
E4 3
2
CPY
Y-M
C0 2
2
C4 3
2
DEC
A A - 1 or MM-1
1A 2
1
C6 5
2
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-84
APPENDIX 3804 Group (Spec.H) 3.7 Machine instructions
Addressing mode ZP, X OP n ZP, Y # OP n ABS # OP n ABS, X # OP n ABS, Y IND ZP, IND # OP n IND, X IND, Y REL SP # OP n 2 # 7
Processor status register 6 V * 5 T * 4 B * 3 D * 2 I * 1 Z * 0 C *
# OP n
# OP n
# OP n
# OP n
# OP n 10 2
N *
80 4
2
*
*
*
*
*
*
*
*
*
*
*
1
*
1
*
*
50 2
2
*
*
*
*
*
*
*
*
70 2
2
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
0
*
*
*
*
0
*
*
*
*
*
*
*
*
0
*
*
*
*
0
*
*
*
*
*
* D5 4 2 CD 4 3 DD 5 3 D9 5 3 C1 6 2 D1 6 2
0
*
*
*
*
*
*
N
*
*
*
*
*
Z
C
N EC 4 3
*
*
*
*
*
Z
*
N
*
*
*
*
*
Z
C
CC 4
3
N
*
*
*
*
*
Z
C
D6 6
2
CE 6
3 DE 7
3
N
*
*
*
*
*
Z
*
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-85
APPENDIX 3804 Group (Spec.H) 3.7 Machine instructions
Addressing mode Symbol Function Details IMP OP n DEX XX-1 YY-1 A (M(zz + X + 1), M(zz + X )) / A M(S) one's complement of Remainder SS-1 When T = 0 - A AVM When T = 1 - M(X) M(X) V M This instruction subtracts one from the current CA 2 contents of X. This instruction subtracts one from the current contents of Y. This instruction divides the 16-bit data in M(zz+(X)) (low-order byte) and M(zz+(X)+1) (high-order byte) by the contents of A. The quotient is stored in A and the one's complement of the remainder is pushed onto the stack. When T = 0, this instruction transfers the contents of the M and A to the ALU which performs a bit-wise Exclusive OR, and stores the result in A. When T = 1, the contents of M(X) and M are transferred to the ALU, which performs a bitwise Exclusive OR and stores the results in M(X). The contents of A remain unchanged, but status flags are changed. M(X) represents the contents of memory where is indicated by X. This instruction adds one to the contents of A or M. This instruction adds one to the contents of X. E8 2 C8 2 1 49 2 2 45 3 2 88 2 IMM # OP n 1 A # OP n BIT, A # OP n ZP # OP n BIT, ZP # OP n #
DEY
1
DIV
EOR (Note 1)
INC
A A + 1 or MM+1 XX+1 YY+1 If addressing mode is ABS PCL ADL PCH ADH If addressing mode is IND PCL M (ADH, ADL) PCH M (ADH, ADL + 1) If addressing mode is ZP, IND PCL M(00, ADL) PCH M(00, ADL + 1) M(S) PCH SS-1 M(S) PCL SS-1 After executing the above, if addressing mode is ABS, PCL ADL PCH ADH if addressing mode is SP, PCL ADL PCH FF If addressing mode is ZP, IND, PCL M(00, ADL) PCH M(00, ADL + 1) When T = 0 AM When T = 1 M(X) M
3A 2
1
E6 5
2
INX
INY JMP
This instruction adds one to the contents of Y. This instruction jumps to the address designated by the following three addressing modes: Absolute Indirect Absolute Zero Page Indirect Absolute
1
JSR
This instruction stores the contents of the PC in the stack, then jumps to the address designated by the following addressing modes: Absolute Special Page Zero Page Indirect Absolute
LDA (Note 2)
When T = 0, this instruction transfers the contents of M to A. When T = 1, this instruction transfers the contents of M to (M(X)). The contents of A remain unchanged, but status flags are changed. M(X) represents the contents of memory where is indicated by X. This instruction loads the immediate value in M. This instruction loads the contents of M in X. This instruction loads the contents of M in Y.
A9 2
2
A5 3
2
LDM
M nn XM YM
3C 4
3
LDX LDY
A2 2 A0 2
2 2
A6 3 A4 3
2 2
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-86
APPENDIX 3804 Group (Spec.H) 3.7 Machine instructions
Addressing mode ZP, X OP n ZP, Y # OP n ABS # OP n ABS, X # OP n ABS, Y IND ZP, IND # OP n IND, X IND, Y REL SP # OP n # 7
Processor status register 6 V * 5 T * 4 B * 3 D * 2 I * 1 Z Z 0 C *
# OP n
# OP n
# OP n
# OP n
# OP n
N N
N
*
*
*
*
*
Z
*
E2 16 2
*
*
*
*
*
*
*
*
55 4
2
4D 4
3 5D 5
3 59 5
3
41 6
2 51 6
2
N
*
*
*
*
*
Z
*
F6 6
2
EE 6
3 FE 7
3
N
*
*
*
*
*
Z
*
N
*
*
*
*
*
Z
*
N 4C 3 3 6C 5 3 B2 4 2 *
* *
* *
* *
* *
* *
Z *
* *
20 6
3
02 7
2
22 5
2
*
*
*
*
*
*
*
*
B5 4
2
AD 4
3 BD 5
3 B9 5
3
A1 6
2 B1 6
2
N
*
*
*
*
*
Z
*
*
*
*
*
*
*
*
*
B6 4 B4 4 2
2 AE 4 AC 4
3 3 BC 5 3
BE 5
3
N N
* *
* *
* *
* *
* *
Z Z
* *
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-87
APPENDIX 3804 Group (Spec.H) 3.7 Machine instructions
Addressing mode Symbol Function Details IMP OP n LSR 7 0 0 C This instruction shifts either A or M one bit to the right such that bit 7 of the result always is set to 0, and the bit 0 is stored in C. This instruction multiply Accumulator with the memory specified by the Zero Page X address mode and stores the high-order byte of the result on the Stack and the low-order byte in A. This instruction adds one to the PC but does EA 2 no other operation. When T = 0, this instruction transfers the contents of A and M to the ALU which performs a bit-wise "OR", and stores the result in A. When T = 1, this instruction transfers the contents of M(X) and the M to the ALU which performs a bit-wise OR, and stores the result in M(X). The contents of A remain unchanged, but status flags are changed. M(X) represents the contents of memory where is indicated by X. This instruction pushes the contents of A to the memory location designated by S, and decrements the contents of S by one. This instruction pushes the contents of PS to the memory location designated by S and decrements the contents of S by one. This instruction increments S by one and stores the contents of the memory designated by S in A. This instruction increments S by one and stores the contents of the memory location designated by S in PS. This instruction shifts either A or M one bit left through C. C is stored in bit 0 and bit 7 is stored in C. 48 3 1 1 09 2 2 05 3 2 IMM # OP n A # OP n 4A 2 BIT, A # OP n 1 ZP # OP n 46 5 BIT, ZP # OP n 2 #
MUL
M(S) * A A M(zz + X) SS-1
NOP
PC PC + 1 When T = 0 AAVM When T = 1 M(X) M(X) V M
ORA (Note 1)
PHA
M(S) A SS-1
PHP
M(S) PS SS-1 SS+1 A M(S) SS+1 PS M(S)
08 3
1
PLA
68 4
1
PLP
28 4
1
ROL
7
0 C
2A 2
1
26 5
2
ROR
7 C
0
This instruction shifts either A or M one bit right through C. C is stored in bit 7 and bit 0 is stored in C.
6A 2
1
66 5
2
RRF
7 SS+1 PS M(S) SS+1 PCL M(S) SS+1 PCH M(S)
0
This instruction rotates 4 bits of the M content to the right.
82 8
2
RTI
This instruction increments S by one, and stores the contents of the memory location designated by S in PS. S is again incremented by one and stores the contents of the memory location designated by S in PCL. S is again incremented by one and stores the contents of memory location designated by S in PCH. This instruction increments S by one and stores the contents of the memory location d e s i g n a t e d b y S i n P C L. S i s a g a i n incremented by one and the contents of the memory location is stored in PCH. PC is incremented by 1.
40 6
1
RTS
SS+1 PCL M(S) SS+1 PCH M(S) (PC) (PC) + 1
60 6
1
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-88
APPENDIX 3804 Group (Spec.H) 3.7 Machine instructions
Addressing mode ZP, X OP n 56 6 ZP, Y # OP n 2 ABS # OP n 4E 6 ABS, X # OP n 3 5E 7 ABS, Y IND ZP, IND # OP n IND, X IND, Y REL SP # OP n # 7
Processor status register 6 V * 5 T * 4 B * 3 D * 2 I * 1 Z Z 0 C C
# OP n 3
# OP n
# OP n
# OP n
# OP n
N 0
62 15 2
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
15 4
2
0D 4
3 1D 5
3 19 5
3
01 6
2 11 6
2
N
*
*
*
*
*
Z
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
N
*
*
*
*
*
Z
*
(Value saved in stack)
36 6
2
2E 6
3 3E 7
3
N
*
*
*
*
*
Z
C
76 6
2
6E 6
3 7E 7
3
N
*
*
*
*
*
Z
C
*
*
*
*
*
*
*
*
(Value saved in stack)
*
*
*
*
*
*
*
*
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-89
APPENDIX 3804 Group (Spec.H) 3.7 Machine instructions
Addressing mode Symbol Function Details IMP OP n SBC (Note 1) (Note 5) When T = 0 _ AA-M-C When T = 1 _ M(X) M(X) - M - C When T = 0, this instruction subtracts the value of M and the complement of C from A, and stores the results in A and C. When T = 1, the instruction subtracts the contents of M and the complement of C from the contents of M(X), and stores the results in M(X) and C. A remain unchanged, but status flag are changed. M(X) represents the contents of memory where is indicated by X. This instruction sets the designated bit i of A or M. This instruction sets C. 38 2 F8 2 78 2 32 2 1 IMM # OP n E9 2 A # OP n 2 BIT, A # OP n ZP # OP n E5 3 BIT, ZP # OP n 2 #
SEB
Ai or Mi 1 C1 D1 I1 T1 MA
0B 2 + 20i
1
0F 5 + 20i
2
SEC
SED
This instruction set D.
1
SEI
This instruction set I.
1
SET
This instruction set T.
1 85 4 2
STA
This instruction stores the contents of A in M. The contents of A does not change. This instruction resets the oscillation control F/ F and the oscillation stops. Reset or interrupt input is needed to wake up from this mode. 42 2 1
STP
STX
MX MY XA YA M = 0? XS AX SX AY
This instruction stores the contents of X in M. The contents of X does not change. This instruction stores the contents of Y in M. The contents of Y does not change. This instruction stores the contents of A in X. The contents of A does not change. This instruction stores the contents of A in Y. The contents of A does not change. This instruction tests whether the contents of M are "0" or not and modifies the N and Z. This instruction transfers the contents of S in BA 2 X. This instruction stores the contents of X in A. 8A 2 1 AA 2 1
86 4 84 4
2
STY
2
TAX
TAY
A8 2
1 64 3 2
TST
TSX
TXA
1
TXS
This instruction stores the contents of X in S.
9A 2
1
TYA
This instruction stores the contents of Y in A.
98 2
1
WIT
The WIT instruction stops the internal clock but not the oscillation of the oscillation circuit is not stopped. CPU starts its function after the Timer X over flows (comes to the terminal count). All registers or internal memory contents except Timer X will not change during this mode. (Of course needs VDD).
C2 2
1
Notes 1 2 3 4 5
: : : : :
The number of cycles "n" is increased by 3 when T is 1. The number of cycles "n" is increased by 2 when T is 1. The number of cycles "n" is increased by 1 when T is 1. The number of cycles "n" is increased by 2 when branching has occurred. N, V, and Z flags are invalid in decimal operation mode.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-90
APPENDIX 3804 Group (Spec.H) 3.7 Machine instructions
Addressing mode ZP, X OP n F5 4 ZP, Y # OP n 2 ABS # OP n ED 4 ABS, X # OP n 3 FD 5 ABS, Y IND ZP, IND # OP n IND, X IND, Y REL SP # OP n # 7
Processor status register 6 V V 5 T * 4 B * 3 D * 2 I * 1 Z Z 0 C C
# OP n 3 F9 5
# OP n 3
# OP n E1 6
# OP n 2 F1 6
# OP n 2
N N
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
1
*
*
*
*
1
*
*
*
*
*
*
*
*
1
*
*
* 95 5 2 8D 5 3 9D 6 3 99 6 3 81 7 2 91 7 2 *
* *
1 *
* *
* *
* *
* *
* *
*
*
*
*
*
*
*
*
96 5 94 5
2 8E 5
3
*
*
*
*
*
*
*
*
2
8C 5
3
*
*
*
*
*
*
*
*
N
*
*
*
*
*
Z
*
N
*
*
*
*
*
Z
*
N
*
*
*
*
*
Z
*
N
*
*
*
*
*
Z
*
N
*
*
*
*
*
Z
*
*
*
*
*
*
*
*
*
N
*
*
*
*
*
Z
*
*
*
*
*
*
*
*
*
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-91
APPENDIX 3804 Group (Spec.H) 3.7 Machine instructions
Symbol IMP IMM A BIT, A BIT, A, R ZP BIT, ZP BIT, ZP, R ZP, X ZP, Y ABS ABS, X ABS, Y IND ZP, IND IND, X IND, Y REL SP C Z I D B T V N
Contents Implied addressing mode Immediate addressing mode Accumulator or Accumulator addressing mode Accumulator bit addressing mode Accumulator bit relative addressing mode Zero page addressing mode Zero page bit addressing mode Zero page bit relative addressing mode Zero page X addressing mode Zero page Y addressing mode Absolute addressing mode Absolute X addressing mode Absolute Y addressing mode Indirect absolute addressing mode Zero page indirect absolute addressing mode Indirect X addressing mode Indirect Y addressing mode Relative addressing mode Special page addressing mode Carry flag Zero flag Interrupt disable flag Decimal mode flag Break flag X-modified arithmetic mode flag Overflow flag Negative flag + - / V V - V - X Y S PC PS PCH PCL ADH ADL FF nn zz M
Symbol
Contents Addition Subtraction Multiplication Division Logical OR Logical AND Logical exclusive OR Negation Shows direction of data flow Index register X Index register Y Stack pointer Program counter Processor status register 8 high-order bits of program counter 8 low-order bits of program counter 8 high-order bits of address 8 low-order bits of address FF in Hexadecimal notation Immediate value Zero page address Memory specified by address designation of any addressing mode Memory of address indicated by contents of index register X Memory of address indicated by contents of stack pointer Contents of memory at address indicated by ADH and ADL, in ADH is 8 high-order bits and ADL is 8 low-order bits. Contents of address indicated by zero page ADL Bit i (i = 0 to 7) of accumulator Bit i (i = 0 to 7) of memory Opcode Number of cycles Number of bytes
M(X) M(S) M(ADH, ADL)
M(00, ADL) Ai Mi OP n #
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-92
APPENDIX 3804 Group (Spec.H) 3.8 List of instruction code
3.8 List of instruction code
D3 - D0 Hexadecimal notation 0 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111
D7 - D4
0
1
2
3
4
5 ORA ZP ORA ZP, X AND ZP AND ZP, X EOR ZP EOR ZP, X ADC ZP ADC ZP, X STA ZP STA ZP, X LDA ZP LDA ZP, X CMP ZP CMP ZP, X SBC ZP SBC ZP, X
6 ASL ZP ASL ZP, X ROL ZP ROL ZP, X LSR ZP LSR ZP, X ROR ZP ROR ZP, X STX ZP STX ZP, Y LDX ZP LDX ZP, Y DEC ZP DEC ZP, X INC ZP INC ZP, X
7 BBS 0, ZP BBC 0, ZP BBS 1, ZP BBC 1, ZP BBS 2, ZP BBC 2, ZP BBS 3, ZP BBC 3, ZP BBS 4, ZP BBC 4, ZP BBS 5, ZP BBC 5, ZP BBS 6, ZP BBC 6, ZP BBS 7, ZP BBC 7, ZP
8
9 ORA IMM ORA ABS, Y AND IMM AND ABS, Y EOR IMM EOR ABS, Y ADC IMM ADC ABS, Y -- STA ABS, Y LDA IMM LDA ABS, Y CMP IMM CMP ABS, Y SBC IMM SBC ABS, Y
A ASL A DEC A ROL A INC A LSR A -- ROR A --
B SEB 0, A CLB 0, A SEB 1, A CLB 1, A SEB 2, A CLB 2, A SEB 3, A CLB 3, A SEB 4, A CLB 4, A SEB 5, A CLB 5, A SEB 6, A CLB 6, A SEB 7, A CLB 7, A
C
D ORA ABS
E ASL ABS
F SEB 0, ZP
0000
BRK
BBS ORA JSR IND, X ZP, IND 0, A ORA IND, Y AND IND, X AND IND, Y EOR IND, X EOR IND, Y CLT JSR SP SET BBC 0, A BBS 1, A BBC 1, A BBS 2, A BBC 2, A BBS 3, A BBC 3, A BBS 4, A BBC 4, A BBS 5, A
--
PHP
--
0001
1
BPL JSR ABS BMI
-- BIT ZP -- COM ZP -- TST ZP -- STY ZP STY ZP, X LDY ZP LDY ZP, X CPY ZP -- CPX ZP --
CLC
-- BIT ABS
ASL CLB ORA ABS, X ABS, X 0, ZP AND ABS ROL ABS SEB 1, ZP
0010
2
PLP
0011
3
SEC
ROL CLB AND LDM ZP ABS, X ABS, X 1, ZP JMP ABS -- JMP IND -- STY ABS -- LDY ABS EOR ABS LSR ABS SEB 2, ZP
0100
4
RTI
STP
PHA
0101
5
BVC
--
CLI
LSR CLB EOR ABS, X ABS, X 2, ZP ADC ABS ROR ABS SEB 3, ZP
0110
6
RTS
MUL ADC IND, X ZP, X ADC IND, Y STA IND, X STA IND, Y LDA IND, X -- RRF ZP -- LDX IMM
PLA
0111
7
BVS
SEI
ROR CLB ADC ABS, X ABS, X 3, ZP STA ABS STA ABS, X LDA ABS STX ABS -- LDX ABS SEB 4, ZP CLB 4, ZP SEB 5, ZP
1000
8
BRA
DEY
TXA
1001
9
BCC LDY IMM BCS CPY IMM BNE CPX IMM BEQ
TYA
TXS
1010
A
TAY
TAX
1011
B
JMP BBC LDA IND, Y ZP, IND 5, A CMP IND, X CMP IND, Y WIT BBS 6, A BBC 6, A BBS 7, A BBC 7, A
CLV
TSX
LDX CLB LDY LDA ABS, X ABS, X ABS, Y 5, ZP CPY ABS -- CPX ABS -- CMP ABS DEC ABS SEB 6, ZP
1100
C
INY
DEX
1101
D
--
CLD
--
DEC CLB CMP ABS, X ABS, X 6, ZP SBC ABS INC ABS SEB 7, ZP
1110
E
DIV SBC IND, X ZP, X SBC IND, Y --
INX
NOP
1111
F
SED
--
INC CLB SBC ABS, X ABS, X 7, ZP
: 3-byte instruction : 2-byte instruction : 1-byte instruction
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-93
APPENDIX 3804 Group (Spec.H) 3.9 SFR memory map
3.9 SFR memory map
000016 000116 000216 000316 000416 000516 000616 000716 000816 000916 000A16 000B16 000C16 000D16 000E16 000F16 001016 001116 001216 001316 001416 001516 001616 001716 001816 001916 001A16 001B16 001C16 001D16 001E16 001F16 Port P0 (P0) Port P0 direction register (P0D) Port P1 (P1) Port P1 direction register (P1D) Port P2 (P2) Port P2 direction register (P2D) Port P3 (P3) Port P3 direction register (P3D) Port P4 (P4) Port P4 direction register (P4D) Port P5 (P5) Port P5 direction register (P5D) Port P6 (P6) Port P6 direction register (P6D) Timer 12, X count source selection register (T12XCSS) Timer Y, Z count source selection register (TYZCSS) MISRG I2C data shift register (S0) I2C special mode status register (S3) I2C status register (S1) I2C control register (S1D) I2C clock control register (S2) I2C START/STOP condition control register (S2D) I2C special mode control register (S3D) Transmit/Receive buffer register 1 (TB1/RB1) Serial I/O1 status register (SIO1STS) Serial I/O1 control register (SIO1CON) UART1 control register (UART1CON) Baud rate generator 1 (BRG1) Serial I/O2 control register (SIO2CON) Watchdog timer control register (WDTCON) Serial I/O2 register (SIO2) 002016 002116 002216 002316 002416 002516 002616 002716 002816 002916 002A16 002B16 002C16 002D16 002E16 002F16 003016 003116 003216 003316 003416 003516 003616 003716 003816 003916 003A16 003B16 003C16 003D16 003E16 003F16 Baud rate generator 3 (BRG3) Transmit/Receive buffer register 3 (TB3/RB3) Serial I/O3 status register (SIO3STS) Serial I/O3 control register (SIO3CON) UART3 control register (UART3CON) AD/DA control register (ADCON) AD conversion register 1 (AD1) DA1 conversion register (DA1) DA2 conversion register (DA2) AD conversion register 2 (AD2) Interrupt source selection register (INTSEL) Interrupt edge selection register (INTEDGE) CPU mode register (CPUM) Interrupt request register 1 (IREQ1) Interrupt request register 2 (IREQ2) Interrupt control register 1 (ICON1) Interrupt control register 2 (ICON2) Prescaler 12 (PRE12) Timer 1 (T1) Timer 2 (T2) Timer XY mode register (TM) Prescaler X (PREX) Timer X (TX) Prescaler Y (PREY) Timer Y (TY) Timer Z low-order (TZL) Timer Z high-order (TZH) Timer Z mode register (TZM) PWM control register (PWMCON) PWM prescaler (PREPWM) PWM register (PWM)
0FE016 0FE116 0FE216 0FE316 0FE416 0FE516 0FE616 0FE716 0FE816 0FE916 0FEA16 0FEB16 0FEC16 0FED16 0FEE16 0FEF16
Flash memory control register 0 (FMCR0) Flash memory control register 1 (FMCR1) Flash memory control register 2 (FMCR2) Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved
0FF016 0FF116 0FF216 0FF316 0FF416 0FF516 0FF616 0FF716 0FF816 0FF916
Port P0 pull-up control register (PULL0) Port P1 pull-up control register (PULL1) Port P2 pull-up control register (PULL2) Port P3 pull-up control register (PULL3) Port P4 pull-up control register (PULL4) Port P5 pull-up control register (PULL5) Port P6 pull-up control register (PULL6) I2C slave address register 0 (S0D0) I2C slave address register 1 (S0D1) I2C slave address register 2 (S0D2)
Reserved area: Do not write any data to these addresses, because these areas are reserved.
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-94
APPENDIX 3804 Group (Spec.H) 3.10 Pin configurations
3.10 Pin configurations
(TOP VIEW)
P01/AN9 P02/AN10 P07/AN15 P10/INT41 P11/INT01 P03/AN11 P04/AN12 P00/AN8 P05/AN13 P06/AN14 P13 P14 P15 35 P16 34 P12 P17 33
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17
44
40
41
45
48
P37/SRDY3 P36/SCLK3 P35/TXD3 P34/RXD3 P33/SCL P32/SDA P31/DA2 P30/DA1 VCC VREF AVSS P67/AN7 P66/AN6 P65/AN5 P64/AN4 P63/AN3
49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64
47
46
43
42
39
38
37
36
P20(LED0) P21(LED1) P22(LED2) P23(LED3) P24(LED4) P25(LED5) P26(LED6) P27(LED7) VSS XOUT XIN P40/INT40/XCOUT P41/INT00/XCIN RESET CNVSS P42/INT1
M38049FFHFP/HP/KP
13
12
P62/AN2
P60/AN0
P56/PWM
P54/CNTR0
P51/SOUT2
10
11
P55/CNTR1
P53/SRDY2
P52/SCLK2
P45/TXD1
P57/INT3
P61/AN1
P50/SIN2
14
15 P44/RXD1
P47/SRDY1/CNTR2
Package type : 64P6N-A/64P6Q-A/64P6U-A
(TOP VIEW)
VCC VREF AVSS P67/AN7 P66/AN6 P65/AN5 P64/AN4 P63/AN3 P62/AN2 P61/AN1 P60/AN0 P57/INT3 P56/PWM P55/CNTR1 P54/CNTR0 P53/SRDY2 P52/SCLK2 P51/SOUT2 P50/SIN2 P47/SRDY1/CNTR2 P46/SCLK1 P45/TXD1 P44/RXD1 P43/INT2 P42/INT1 CNVSS RESET P41/INT00/XCIN P40/INT40/XCOUT XIN XOUT VSS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 P30/DA1 P31/DA2 P32/SDA P33/SCL P34/RXD3 P35/TXD3 P36/SCLK3 P37/SRDY3 P00/AN8 P01/AN9 P02/AN10 P03/AN11 P04/AN12 P05/AN13 P06/AN14 P07/AN15 P10/INT41 P11/INT01 P12 P13 P14 P15 P16 P17 P20(LED0) P21(LED1) P22(LED2) P23(LED3) P24(LED4) P25(LED5) P26(LED6) P27(LED7)
Package type : 64P4B
P46/SCLK1
P43/INT2
16
5
4
1
3
2
6
7
8
9
M38049FFHSP
Rev.1.00 Jan 14, 2005 REJ09B0212-0100Z
3-95
3804 Group (Spec. H) User's Manual Publication Data : Published by : Rev.1.00 Jan 14, 2005 Sales Strategic Planning Div. Renesas Technology Corp.
(c) 2005. Renesas Technology Corp., All rights reserved. Printed in Japan.
3804 Group (Spec. H) User's Manual
2-6-2, Ote-machi, Chiyoda-ku, Tokyo, 100-0004, Japan


▲Up To Search▲   

 
Price & Availability of M38043F8FP

All Rights Reserved © IC-ON-LINE 2003 - 2022  
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy]
Mirror Sites :  [www.datasheet.hk]   [www.maxim4u.com]  [www.ic-on-line.cn] [www.ic-on-line.com] [www.ic-on-line.net] [www.alldatasheet.com.cn] [www.gdcy.com]  [www.gdcy.net]
 . . . . .
  We use cookies to deliver the best possible web experience and assist with our advertising efforts. By continuing to use this site, you consent to the use of cookies. For more information on cookies, please take a look at our Privacy Policy. X